GD32F350定时器14PWM输出

最新推荐文章于 2024-07-29 16:42:48 发布

houdezaiwu2020

最新推荐文章于 2024-07-29 16:42:48 发布

阅读量387

点赞数 8

文章标签：单片机 stm32

本文链接：https://blog.csdn.net/liuhfeng21/article/details/135641913

版权

本文详细描述了如何在STM32中配置定时器14，包括时钟设置、计数器方向、周期、PWM通道配置以及中断处理。重点展示了如何将GPIOA的PIN_2用于PWM输出并启用定时器中断。

摘要由CSDN通过智能技术生成

void timer14_config(void)
{
    timer_oc_parameter_struct timer_ocintpara;
    timer_parameter_struct timer_initpara;

    rcu_periph_clock_enable(RCU_TIMER14);
	rcu_periph_clock_enable(RCU_GPIOA);


    gpio_mode_set(GPIOA, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO_PIN_2);
    gpio_output_options_set(GPIOA, GPIO_OTYPE_PP, GPIO_OSPEED_MAX,GPIO_PIN_2);
    gpio_af_set(GPIOA, GPIO_AF_0, GPIO_PIN_2); 

    timer_deinit(TIMER14);

    /* TIMER1 configuration */

    timer_initpara.prescaler         = 0;

    timer_initpara.alignedmode       = TIMER_COUNTER_EDGE;
    timer_initpara.counterdirection  = TIMER_COUNTER_UP;
    timer_initpara.period            = 10800;
    timer_initpara.clockdivision     = TIMER_CKDIV_DIV1;
    timer_initpara.repetitioncounter = 0;
    timer_init(TIMER14,&timer_initpara);

    /* CH1,CH2 and CH3 configuration in PWM mode */
    timer_ocintpara.outputstate  = TIMER_CCX_ENABLE;
    timer_ocintpara.outputnstate = TIMER_CCXN_DISABLE;
    timer_ocintpara.ocpolarity   = TIMER_OC_POLARITY_HIGH;
    timer_ocintpara.ocnpolarity  = TIMER_OCN_POLARITY_HIGH;
    timer_ocintpara.ocidlestate  = TIMER_OC_IDLE_STATE_LOW;
    timer_ocintpara.ocnidlestate = TIMER_OCN_IDLE_STATE_LOW;

    timer_channel_output_config(TIMER14,TIMER_CH_0,&timer_ocintpara);

    timer_channel_output_pulse_value_config(TIMER14,TIMER_CH_0,1);
    timer_channel_output_mode_config(TIMER14,TIMER_CH_0,TIMER_OC_MODE_PWM0);
    timer_channel_output_shadow_config(TIMER14,TIMER_CH_0,TIMER_OC_SHADOW_DISABLE);
	
	
    timer_primary_output_config(TIMER14, ENABLE);
//    timer_interrupt_flag_clear(TIMER14, TIMER_INT_FLAG_CH0);
//    /* enable the TIMER interrupt */
//    timer_interrupt_enable(TIMER14, TIMER_INT_CH0);
//    nvic_irq_enable(TIMER16_IRQn, 0,0);
    /* auto-reload preload enable */
    timer_auto_reload_shadow_enable(TIMER14);
    /* auto-reload preload enable */
    timer_enable(TIMER14);
    
}