rv1126-rv1109-读取mipi摄像头ID

1.有那个一个需求，需要读取mipi摄像头ID

起初，我以为很简单，实际非常复杂；

2.移植原有的逻辑，就是操作I2C函数读取ID寄存器，但是一直失败；

3.然后发现是电源没有打开；然后电源又是在DTS里面配置的

 4.配置电源后发现要配置时钟

5.配置时钟后发现还要配置摄像头的上电时序

最后是自己构建了一个lbdrv_data的结构体存储这些数据,然后自己定制的驱动里面实现控制

补丁:

diff --git a/sysdrv/source/kernel/drivers/lonbon/lbdrv/lbdrv_probe.c b/sysdrv/source/kernel/drivers/lonbon/lbdrv/lbdrv_probe.c
old mode 100644
new mode 100755
index 2a2d9689c..b432a6d7d
--- a/sysdrv/source/kernel/drivers/lonbon/lbdrv/lbdrv_probe.c
+++ b/sysdrv/source/kernel/drivers/lonbon/lbdrv/lbdrv_probe.c
@@ -42,19 +42,20 @@

 static struct i2c_client *sensor_client;
 static struct proc_dir_entry *proc_lbdrv;
+struct lbdrv_data *lbdrv_power_data;^M

 static reg_table gc2053_sensor_id_table[] =
 {
        {0xf0, 0x20},
        {0xf1, 0x53},
 };
-#if 0
+^M
 static reg_table gc4653_sensor_id_table[] =
 {
        {0x03f0, 0x46},
        {0x03f1, 0x53},
 };
-
+#if 0^M
 static reg_table sc200ai_sensor_id_table[] =
 {
     {0x3107, 0xCB},
@@ -72,7 +73,7 @@ static reg_table ov2710_sensor_id_table[] =
 static const struct sensor_info sensor_list[] = {
        /* name | slave addr | reg addr | reg value | reg addr bytes | reg value bytes */
        {"gc2053", 0x6e, gc2053_sensor_id_table, ARRAY_SIZE(gc2053_sensor_id_table), 0x01, 0x01,LBDRV_MCLK_72M},        // for galaxycore gc2053
-       //{"gc4653", 0x52, gc4653_sensor_id_table, ARRAY_SIZE(gc4653_sensor_id_table), 0x02, 0x01,LBDRV_MCLK_72M},      // for galaxycore gc2053
+       {"gc4653", 0x52, gc4653_sensor_id_table, ARRAY_SIZE(gc4653_sensor_id_table), 0x02, 0x01,LBDRV_MCLK_72M},        // for galaxycore gc4653^M
        //{"sc200ai",0x60, sc200ai_sensor_id_table, ARRAY_SIZE(sc200ai_sensor_id_table), 0x02, 0x01,SNR_MCLK_27M},      // for smartsens sc200ai
        //{"ov2710", 0x6c, ov2710_sensor_id_table, ARRAY_SIZE(ov2710_sensor_id_table), 0x02, 0x01,SNR_MCLK_24M},   // for omnivision ov2710
 };
@@ -95,6 +96,190 @@ static void lbdrv_set_i2c_addr_idle(struct i2c_client *cli)
        }
 }

+static inline u32 lbdrv_cal_delay(u32 cycles)^M
+{^M
+       return DIV_ROUND_UP(cycles, LBDRV_XVCLK_FREQ / 1000 / 1000);^M
+}^M
+^M
+int lbdrv_power_on_gc2053(void){^M
+       int ret;^M
+       u32 delay_us;^M
+^M
+       ret = clk_set_rate(lbdrv_power_data->xvclk, LBDRV_XVCLK_FREQ);^M
+       if (ret < 0)^M
+               lbdrv_info("Failed to set xvclk rate (24MHz)\n");^M
+       if (clk_get_rate(lbdrv_power_data->xvclk) != LBDRV_XVCLK_FREQ)^M
+               lbdrv_info("xvclk mismatched, modes are based on 24MHz\n");^M
+       ret = clk_prepare_enable(lbdrv_power_data->xvclk);^M
+       if (ret < 0) {^M
+               lbdrv_err("Failed to enable xvclk\n");^M
+               return ret;^M
+       }^M
+^M
+       ret = regulator_bulk_enable(LBDRV_NUM_SUPPLIES, lbdrv_power_data->supplies);^M
+       if (ret < 0) {^M
+               lbdrv_info("Failed to enable regulators\n");^M
+               goto disable_clk;^M
+       }^M
+       if (!IS_ERR(lbdrv_power_data->power_gpio)) {^M
+               gpiod_set_value_cansleep(lbdrv_power_data->power_gpio, 1);^M
+               usleep_range(100, 200);^M
+       }^M
+       if (!IS_ERR(lbdrv_power_data->reset_gpio)) {^M
+               gpiod_set_value_cansleep(lbdrv_power_data->reset_gpio, 1);^M
+               usleep_range(100, 200);^M
+       }^M
+       if (!IS_ERR(lbdrv_power_data->pwdn_gpio))^M
+               gpiod_set_value_cansleep(lbdrv_power_data->pwdn_gpio, 0);^M
+^M
+       if (!IS_ERR(lbdrv_power_data->reset_gpio))^M
+               gpiod_set_value_cansleep(lbdrv_power_data->reset_gpio, 0);^M
+       usleep_range(3000, 6000);^M
+       /* 8192 cycles prior to first SCCB transaction */^M
&