USRP_B210的FPGA代码分析之：B210顶层接口分析

接下来我要研究USRP B210的FPGA驱动，用来移植到自己的软件无线电产品上。看顶层接口代码：

/***********************************************************
 * B200 Module Declaration
 **********************************************************/
module b200 (
   // SPI Interfaces
   output 	 cat_ce,
   input 	 cat_miso,
   output 	 cat_mosi,
   output 	 cat_sclk,

   input 	 fx3_ce,
   output 	 fx3_miso,
   input 	 fx3_mosi,
   input 	 fx3_sclk,

   output 	 pll_ce,
   output 	 pll_mosi,
   output 	 pll_sclk,

   // UART
   // By default these provide an FX3 UART console output. Under compile time control they can alternatively
   // provide 2 (1.8V) GPIO pins which are logically bits [9:8] of the fp_gpio bus.
   // Used as a UART RXD is an input and TXD an output electrically.
  // input 	 FPGA_RXD0, // These pins goto 3 pin 0.1" header on B2x0 and
  // output 	 FPGA_TXD0, // carry FX3 UART.
   inout 	 FPGA_RXD0, // These pins goto 3 pin 0.1" header J400 on B2x0 and
   inout 	 FPGA_TXD0, // carry FX3 UART.

   // Catalina Controls
   output 	 codec_enable,
   output 	 codec_en_agc,
   output 	 codec_reset,
   output 	 codec_sync,
   output 	 codec_txrx,
   output [3:0]  codec_ctrl_in, // These should be outputs
   input [7:0] 	 codec_ctrl_out, // MUST BE INPUT

   // Catalina Data
   input 	 codec_data_clk_p, // Clock from CAT (RX)
   output 	 codec_fb_clk_p, // Clock to CAT (TX)
   input [11:0]  rx_codec_d,
   output [11:0] tx_codec_d,
   input 	 rx_frame_p,
   output 	 tx_frame_p,

   input 	 cat_clkout_fpga,

   //always on 40MHz clock
   input 	 codec_main_clk_p,
   input 	 codec_main_clk_n,

   // Debug Bus
 //  output [31:0] debug,
  // output [1:0]  debug_clk,

   // GPIF, FX3 Slave FIFO
   output 	 IFCLK, // pclk
   input 	 FX3_EXTINT,
   output 	 GPIF_CTL0, // n_slcs
   output 	 GPIF_CTL1, // n_slwr
   output 	 GPIF_CTL2, // n_sloe
   output 	 GPIF_CTL3, // n_slrd
   output 	 GPIF_CTL7, // n_pktend
   input 	 GPIF_CTL4, // slfifo_flags[0]
   input 	 GPIF_CTL5, // slfifo_flags[1]
   input 	 GPIF_CTL6, // Serial settings bus from FX3. SDA
   input 	 GPIF_CTL8, // Serial settings bus from FX3. SCL
   output 	 GPIF_CTL11, // slfifo_addr[1]
   output 	 GPIF_CTL12, // slfifo_addr[0]
   inout [31:0]  GPIF_D,
   input 	 GPIF_CTL9, // global_reset

   // GPS
   //input 	 gps_lock,
   output 	 gps_rxd,
   input 	 gps_txd, // FPGA has pullup for unpopulated GPS
   //input 	 gps_txd_nmea, // FPGA has pullup for unpopulated GPS

   // LEDS
   output 	 LED_RX1,
   output 	 LED_RX2,
   output 	 LED_TXRX1_RX,
   output 	 LED_TXRX1_TX,
   output 	 LED_TXRX2_RX,
   output 	 LED_TXRX2_TX,

   // GPIO Header J504  - 10 pin 0.1" 3.3V.
   // Only present on Rev6 and later boards...these pins unused on Rev5 and earlier.
   // NOTE: These pins are allocated from complimentry pairs and could potentially be used
   // as differential style I/O.
  `ifdef TARGET_B210
   inout [7:0] 	 fp_gpio,
  `endif
   // Misc Hardware Control
   output 	 ref_sel,
   input 	 pll_lock,
   input 	 FPGA_CFG_CS, // Driven by FX3 gpio.
   input 	 AUX_PWR_ON, // Driven by FX3 gpio.

   // PPS
   input 	 PPS_IN_EXT,
   input 	 PPS_IN_INT,

   // RF Hardware Control
   output 	 SFDX1_RX,
   output 	 SFDX1_TX,
   output 	 SFDX2_RX,
   output 	 SFDX2_TX,
   output 	 SRX1_RX,
   output 	 SRX1_TX,
   output 	 SRX2_RX,
   output 	 SRX2_TX,
   output 	 tx_bandsel_a,
   output 	 tx_bandsel_b,
   output 	 tx_enable1,
   output 	 tx_enable2,
   output 	 rx_bandsel_a,
   output 	 rx_bandsel_b,
   output 	 rx_bandsel_c
   );
		

我们一点点的品一下：

 

 

 

 

对于适当了解USRP B210硬件的，能很容易对应起来上述的接口和实际芯片的连接。内部的各个模块以及连接和各自之间的逻辑我们接下来再分析。