VLAN路由之间的通信

Vlan间路由

方法一:多层交换机---SVI(常用):switch vitual interface

方法二:单臂路由

注意:不同的VLAN间的通信必须要有三层设备做中转(路由器、多层交换机）

 

1.创建vlan

[111]vlan batch 10 20

2.划分接口

[111]int gi0/0/1

[111-GigabitEthernet0/0/1]port link-type access

[111-GigabitEthernet0/0/1]port default vlan 10

[111-GigabitEthernet0/0/1]int gi0/0/2

[111-GigabitEthernet0/0/2]port link-type access

[111-GigabitEthernet0/0/2]port default vlan 20

3.给vlan配置地址

[111]int vlan 10

[111-Vlanif10]ip add

[111-Vlanif10]ip address 192.168.10.1 24

[111-Vlanif10]q

[111]int vlan 20

[111-Vlanif20]ip address 192.168.20.1 24

 

配置主机地址

 

查看路由表

 

成功ping通

 

 

配置LSW2

1.创建vlan

[111]vlan batch 10 20

2.划分接口

[333]vlan batch 10 20

[333]int gi0/0/2

[333-GigabitEthernet0/0/2]int gi0/0/1

[333-GigabitEthernet0/0/1]port link-type trunk

[333-GigabitEthernet0/0/1]port trunk allow-pass vlan all

为vlan10 20配置ip

[333]vlan 10

[333-Vlanif10]ip address 192.168.10.254 24

[333]int vlan 20

[333-Vlanif20]ip address 192.168.20.254 24

 

配置LSW3

[111]vlan batch 10 20

[111]int gi0/0/1

[111-GigabitEthernet0/0/1]port link-type trunk

[111-GigabitEthernet0/0/1]port trunk allow-pass vlan all

[111-GigabitEthernet0/0/1]int gi0/0/2

[111-GigabitEthernet0/0/2]port link-type access

[111-GigabitEthernet0/0/2]port default vlan 10

[111-GigabitEthernet0/0/2]int gi0/0/3

[111-GigabitEthernet0/0/3]port link-type access

[111-GigabitEthernet0/0/3]port default vlan 20

[111-GigabitEthernet0/0/3]q

 

配置LSW4

[222]vlan batch 10 20

[222]int gi0/0/1

[222-GigabitEthernet0/0/1]port link-type trunk

[222-GigabitEthernet0/0/1]port trunk allow-pass vlan all

[222-GigabitEthernet0/0/1]int gi0/0/2

[222-GigabitEthernet0/0/2]port link-type access

[222-GigabitEthernet0/0/2]port default vlan 20

[222-GigabitEthernet0/0/2]int gi0/0/3

[222-GigabitEthernet0/0/3]port link-type access

[222-GigabitEthernet0/0/3]port default vlan 10

[222-GigabitEthernet0/0/3]q

 

 

 

成功ping通