数码管显示

本程序对应的开发板为蓝桥杯嵌入式开发板stm32f103rbt6，为中型mcu。嵌入式竞赛开发板上的3位数码管是共阴极静态显示，使用输出锁的8位移位寄存器74LS595驱动，其引脚功能如下

硬件连接

P4.1（PA1）-P3.1（SER）

P4.2（PA2）-P3.2（RCK）

P4.3（PA3）-P3.3（SCK）

同时断开

J1.3（PA3）-J2.3（RXD2）

J1.4（PA2）-J2.4（TXD2）

由于数码管和USART2都使用了PA2和PA3的引脚，使用数码管和USART不能同时使用

初始化程序

void SEG_Init(void)
{
	  GPIO_InitTypeDef GPIO_InitStructure;
	  RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
	  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1 | GPIO_Pin_2| GPIO_Pin_3;
	  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
	  GPIO_Init(GPIOA, &GPIO_InitStructure);



}

数码管显示函数

//入口参数：data1~3显示三个数据，dot 3个小数点
void SEG_Dis(unsigned char data1,unsigned char data2,unsigned char data3,unsigned char dot)
{
unsigned char i;
unsigned long data;
unsigned char code[17]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f,0x77,0x7c,0x39,0x5e,0x79,0x71,0x00};

data=((code[data3]<<16)+(code[data2]<<8)+(code[data1]));

data+=(dot&1)<<23;
data+=(dot&2)<<14;
data+=(dot%4)<<5;

GPIO_ResetBits(GPIOA,GPIO_Pin_2);	   //pa2(rck)=0
for(i=0;i<24;i++)
{
GPIO_ResetBits(GPIOA,GPIO_Pin_3);		//pa3(sck)=0
if(data&0x800000)						//从高位开始送
GPIO_SetBits(GPIOA,GPIO_Pin_1);			//pa1(ser)=1
else
GPIO_ResetBits(GPIOA,GPIO_Pin_1);		//pa1(ser)=0
data<<=1;
GPIO_SetBits(GPIOA,GPIO_Pin_3);			//pa3(sck)=1


}

GPIO_SetBits(GPIOA,GPIO_Pin_2);		   //pa2(sck)=1



}

主程序

#include "stm32f10x.h"
#include "lcd.h"

u32 TimingDelay = 0;

void Delay_Ms(u32 nTime);
void SEG_Init(void);
void SEG_Dis(unsigned char data1,unsigned char data2,unsigned char data3,unsigned char dot);
unsigned int Seg=0;
unsigned char Sec=0,Sec1=0,dot=0;
unsigned Tick_ms=0;

int main(void)
{
  
    STM3210B_LCD_Init();
	LCD_Clear(Blue);
	LCD_SetBackColor(Blue);
	LCD_SetTextColor(White);
	
	SysTick_Config(SystemCoreClock/1000);
	SEG_Init();
	SEG_Dis(0x10,0x10,0x10,0);	//先把三个数码管全部熄灭

	
	LCD_DisplayStringLine(Line0,"                    ");	
	LCD_DisplayStringLine(Line1,"                    ");	
	LCD_DisplayStringLine(Line2,"                    ");
	LCD_DisplayStringLine(Line3,"                    ");
	LCD_DisplayStringLine(Line4,"                    ");
	LCD_DisplayStringLine(Line5,"                    ");
	LCD_DisplayStringLine(Line6,"                    ");
	LCD_DisplayStringLine(Line7,"                    ");	
	LCD_DisplayStringLine(Line8,"                    ");
	LCD_DisplayStringLine(Line9,"                    ");	
	


  //依次显示0-999
  while (1)
  {
   if(Sec1!=Sec)
   {
   Sec1=Sec;
   SEG_Dis((Seg&0xf00)>>8,(Seg&0xf0)>>4,(Seg&0xf),dot++);
   Seg+=0x111;
   if(Seg>0x1000)
   Seg=0;

   
   }
  }
}


void Delay_Ms(u32 nTime)
{
	TimingDelay = nTime;
	while(TimingDelay != 0);	
}