GD32F303固件库开发（14）----IIC之配置OLED

已于 2023-02-21 14:51:04 修改
阅读量2.2w 收藏 28
点赞数 9
分类专栏： GD32 单片机 文章标签： 单片机 stm32 嵌入式硬件
于 2022-09-08 15:45:37 首次发布
本文链接：https://blog.csdn.net/qq_24312945/article/details/126764514
版权
单片机 同时被 2 个专栏收录
229 篇文章 138 订阅
订阅专栏
GD32
36 篇文章 119 订阅
订阅专栏

GD32F303固件库开发.13----定时器TIM捕获PWM测量频率与占空比

概述

本章配置GD32F303使用IIC进行驱动SSD1306的12864OLED。
查阅手册可以得知，PB10、PB11为I2C的接口。
需要GD样片的可以加群申请：615061293 。

在这里插入图片描述

在这里插入图片描述

视频教学

https://www.bilibili.com/video/BV1od4y1u7t7/

GD32F303固件库开发（14）----IIC之配置OLED

csdn课程

课程更加详细。
https://download.csdn.net/course/detail/37144

样品申请

https://www.wjx.top/vm/wFGhGPF.aspx#

参考文档

GD官方文档GD32F30x_Firmware_Library_V2.1.4下面IIC的Master_transmitter&slave_receiver

时钟使能

/*!
    \brief      enable the peripheral clock
    \param[in]  none
    \param[out] none
    \retval     none
*/
void rcu_config(void)
{
    /* enable GPIOB clock */
    rcu_periph_clock_enable(RCU_GPIOB);
    /* enable I2C1 clock */
    rcu_periph_clock_enable(RCU_I2C1);
}

初始化IO

/*!
    \brief      cofigure the GPIO ports
    \param[in]  none
    \param[out] none
    \retval     none
*/
void gpio_config(void)
{

    /* connect PB10 to I2C1_SCL */
    /* connect PB11 to I2C1_SDA */
    gpio_init(GPIOB, GPIO_MODE_AF_OD, GPIO_OSPEED_50MHZ,  GPIO_PIN_10 | GPIO_PIN_11);
}

IIC初始化

/*!
    \brief      cofigure the I2C0 and I2C1 interfaces
    \param[in]  none
    \param[out] none
    \retval     none
*/
void i2c_config(void)
{

    i2c_clock_config(I2C1, 100000, I2C_DTCY_2);
    /* I2C address configure */
    i2c_mode_addr_config(I2C1, I2C_I2CMODE_ENABLE, I2C_ADDFORMAT_7BITS, 0x78);
    /* enable I2C1 */
    i2c_enable(I2C1);
    /* enable acknowledge */
    i2c_ack_config(I2C1, I2C_ACK_ENABLE);
}

配置IIC接口

/*!
    \brief      cofigure the  I2C1 interfaces
    \param[in]  none
    \param[out] none
    \retval     none
*/
void i2c_config(void)
{

    /* configure I2C1 clock */
    i2c_clock_config(I2C1, 100000, I2C_DTCY_2);
    /* configure I2C1 address */
    i2c_mode_addr_config(I2C1, I2C_I2CMODE_ENABLE, I2C_ADDFORMAT_7BITS, 0x78);
    /* enable I2C1 */
    i2c_enable(I2C1);
    /* enable acknowledge */
    i2c_ack_config(I2C1, I2C_ACK_ENABLE);
}

修改IIC发送代码

将Master_transmitter&slave_receiver的IIC发送代码进行修改

在这里插入图片描述

/**
  * @brief I2C1写函数
  * @param addr设备地址
  * @param pdata 数据指针
  * @param data_length 数据长度
  */
void i2c_write(uint8_t addr, uint8_t *pdata, uint32_t data_length)
{
    uint32_t i;
    
    /* wait until I2C bus is idle */
    while(i2c_flag_get(I2C1, I2C_FLAG_I2CBSY));//等待总线空闲
    /* send a start condition to I2C bus */
    i2c_start_on_bus(I2C1);//发送start信号
    /* wait until SBSEND bit is set */
    while(!i2c_flag_get(I2C1, I2C_FLAG_SBSEND));    //起始位是否发送
    /* send slave address to I2C bus */
    i2c_master_addressing(I2C1, addr, I2C_TRANSMITTER);//设置从机地址和执行发送操作
    /* wait until ADDSEND bit is set */
    while(!i2c_flag_get(I2C1, I2C_FLAG_ADDSEND));//主机模式下地址是否发送
    /* clear ADDSEND bit */
    i2c_flag_clear(I2C1, I2C_FLAG_ADDSEND);//清除标志位主机模式下地址是否发送
    /* wait until the transmit data buffer is empty */
    while(!i2c_flag_get(I2C1, I2C_FLAG_TBE));//发送期间I2C_DATA为空
    for(i = 0; i < data_length; i++){
        /* data transmission */
        i2c_data_transmit(I2C1, pdata[i]);//发送数据
        /* wait until the TBE bit is set */
        while(!i2c_flag_get(I2C1, I2C_FLAG_TBE));//发送期间I2C_DATA为空
    }
    /* send a stop condition to I2C bus */
    i2c_stop_on_bus(I2C1);//在I2C总线上生成停止位
    /* wait until stop condition generate */ 
    while(I2C_CTL0(I2C1)&0x0200);  //等待直到停止条件生成  
}

OLED

查看文档可以知道地址为b0111100或者b0111101，当R/W位置写0的时候，才能进行写的操作，那么地址默认为0x78(b01111000)或者0x7A(b01111010)
在这里插入图片描述

参考程序

这里使用0.96OLED显示屏_STM32F103C8_IIC_V1.0来进行移植
在这里插入图片描述
在这里插入图片描述
查看工程可以知道主要是有3个文件来进行OLED的驱动，移入OLE.h .c 、oledfont.h 、 bmp.h
移入文件之后要注意导入C文件。
在这里插入图片描述
记得添加路径。
在这里插入图片描述
删除没有用的头文件
删除sys.h文件
在这里插入图片描述
删除delay.h文件
在这里插入图片描述

可以查看stdint.h

在这里插入图片描述
在oled.h中添加u8 u32定义 也可以直接修改

typedef unsigned          char u8;
typedef unsigned           int u32;

在这里插入图片描述
先把oled.h添加主程序中。
在这里插入图片描述

查看oled.h，可以看到IIC定义，同时也是模拟IIC，可以注释掉
在这里插入图片描述
查看oled.c，可以看到是模拟iic，这些都可以注释不要，我们使用的是iIC，不是模拟。
在这里插入图片描述
将IIC写放入oled.c中。
记得导入#include "gd32f30x_i2c.h"头文件
在这里插入图片描述

记得在oled.h中申明
要使用uint8和uint32，导入头文件#include “stdint.h”

在这里插入图片描述
IIC写一个字节可以修改为如下所示。
在这里插入图片描述

/**********************************************
// IIC Write byte
**********************************************/

void Write_IIC_Byte(unsigned char IIC_Byte)
{
//	unsigned char i;
//	unsigned char m,da;
//	da=IIC_Byte;
//	OLED_SCLK_Clr();
//	for(i=0;i<8;i++)		
//	{
//			m=da;
//		//	OLED_SCLK_Clr();
//		m=m&0x80;
//		if(m==0x80)
//		{OLED_SDIN_Set();}
//		else OLED_SDIN_Clr();
//			da=da<<1;
//		OLED_SCLK_Set();
//		OLED_SCLK_Clr();
//		}

uint8_t byte[1] = {};	
byte[0]=IIC_Byte;
i2c_write(0x78,byte, 1);			
}

IIC写指令
向0x78设备写命令0x00的IIC_Command指令。
在这里插入图片描述

/**********************************************
// IIC Write Command
**********************************************/
void Write_IIC_Command(unsigned char IIC_Command)
{
//   IIC_Start();
//   Write_IIC_Byte(0x78);            //Slave address,SA0=0
//	IIC_Wait_Ack();	
//   Write_IIC_Byte(0x00);			//write command
//	IIC_Wait_Ack();	
//   Write_IIC_Byte(IIC_Command); 
//	IIC_Wait_Ack();	
//   IIC_Stop();
	
	
	uint8_t byte[2] = {};	
	byte[0]	=0x00;
	byte[1]	=IIC_Command;	
	i2c_write(0x78,byte, 2);				
}

IIC写数据
向0x78设备写数据0x40的IIC_Data指令。
在这里插入图片描述

/**********************************************
// IIC Write Data
**********************************************/
void Write_IIC_Data(unsigned char IIC_Data)
{
//   IIC_Start();
//   Write_IIC_Byte(0x78);			//D/C#=0; R/W#=0
//	IIC_Wait_Ack();	
//   Write_IIC_Byte(0x40);			//write data
//	IIC_Wait_Ack();	
//   Write_IIC_Byte(IIC_Data);
//	IIC_Wait_Ack();	
//   IIC_Stop();
	
	
	uint8_t byte[2] = {};	
	byte[0]	=0x40;
	byte[1]	=IIC_Data;	
	i2c_write(0x78,byte, 2);		
	
}

在oled.c中，OLED_Init初始化可以注释掉gpio初始化
在这里插入图片描述

在oled.c中，OLED_Init初始化中有个延时800ms。
导入
#include “systick.h”
可以使用delay_1ms(800);
在这里插入图片描述

取模

在这里插入图片描述
在这里插入图片描述

在oledfont.h中放入字库
在这里插入图片描述

char Hzk[][32]={

// 记(0) 帖(1) 年(2) 月(3) 日(4)

{0x40,0x40,0x42,0xCC,0x00,0x00,0x00,0x84,0x84,0x84,0x84,0x84,0xFC,0x00,0x00,0x00},
{0x00,0x00,0x00,0x7F,0x20,0x10,0x00,0x3F,0x40,0x40,0x40,0x40,0x41,0x40,0x70,0x00},/*"记",0*/
/* (16 X 16 , 宋体 )*/

{0x00,0xF8,0x08,0xFF,0x08,0xF8,0x00,0x00,0x00,0x00,0xFF,0x10,0x10,0x10,0x10,0x00},
{0x00,0x0F,0x00,0xFF,0x08,0x0F,0x00,0xFF,0x41,0x41,0x41,0x41,0x41,0xFF,0x00,0x00},/*"帖",1*/
/* (16 X 16 , 宋体 )*/

{0x00,0x20,0x18,0xC7,0x44,0x44,0x44,0x44,0xFC,0x44,0x44,0x44,0x44,0x04,0x00,0x00},
{0x04,0x04,0x04,0x07,0x04,0x04,0x04,0x04,0xFF,0x04,0x04,0x04,0x04,0x04,0x04,0x00},/*"年",2*/
/* (16 X 16 , 宋体 )*/

{0x00,0x00,0x00,0xFE,0x22,0x22,0x22,0x22,0x22,0x22,0x22,0x22,0xFE,0x00,0x00,0x00},
{0x80,0x40,0x30,0x0F,0x02,0x02,0x02,0x02,0x02,0x02,0x42,0x82,0x7F,0x00,0x00,0x00},/*"月",3*/
/* (16 X 16 , 宋体 )*/

{0x00,0x00,0x00,0xFE,0x82,0x82,0x82,0x82,0x82,0x82,0x82,0xFE,0x00,0x00,0x00,0x00},
{0x00,0x00,0x00,0xFF,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0xFF,0x00,0x00,0x00,0x00},/*"日",4*/
/* (16 X 16 , 宋体 )*/




};

在main.c中添加显示

			OLED_Init();			//初始化OLED  
		OLED_Clear()  	; 
		OLED_ShowCHinese(0,0,0);//记
		OLED_ShowCHinese(16,0,1);//帖
		
		
		OLED_ShowNum(0,2,2022,4,16);//显示ASCII字符的码值 			
		OLED_ShowCHinese(32,2,2);//年	
		OLED_ShowNum(48,2,9,1,16);//显示ASCII字符的码值 		
		OLED_ShowCHinese(64,2,3);//月
		OLED_ShowNum(80,2,10,2,16);//显示ASCII字符的码值 				
		OLED_ShowCHinese(96,2,4);//日

字体大小只有2个
在这里插入图片描述

显示字符

OLED_ShowString(40,2,"ZXY",8);

在这里插入图片描述

图片

在这里插入图片描述
图片放在bmp.h中。

#ifndef __BMP_H
#define __BMP_H		

unsigned char BMP1[]={
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x1F,0x1F,0x1F,0x7F,0xFF,0xFF,
0xFF,0xFF,0xFF,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x0F,0x0F,
0x0F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,
0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xC7,0xC7,0xC7,0xC4,0x04,0x04,0x04,0x07,0xFF,
0xFF,0xFF,0xFF,0x0F,0x0F,0x0F,0x0F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x8F,0x80,0x80,
0x80,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xE3,0xE3,0xE3,0xE3,0xE3,0xE3,
0xE3,0xE3,0xE3,0xE3,0xE3,0xE3,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x00,0x00,0x00,0x00,0x1F,
0x1F,0x1F,0xFF,0x00,0x00,0x00,0x00,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x8F,0x8F,0x8F,
0x8F,0x8F,0x8F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x0F,0x0F,0x0F,
0x0F,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFE,0x06,0x06,0x07,0x0F,
0xFF,0xFF,0xFF,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0xF8,0x00,0x00,
0x00,0x00,0xF8,0xF8,0xF8,0xF8,0xF8,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x00,0x00,0x00,
0x00,0xC7,0xC7,0xC7,0xC7,0xC7,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x00,0x00,0x00,0x00,
0xFF,0x00,0x00,0x00,0xFF,0xFF,0x0F,0x0F,0x0F,0xFF,0xFF,0xFF,0xFF,0xFF,0x00,0x00,
0x00,0x00,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0x03,0x03,0x03,0x03,0xE3,0xE0,0xE0,0xE0,
0xE0,0xE3,0xE3,0x03,0x03,0x03,0x03,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xF0,0xF0,0xF0,0xF0,
0xFF,0xF0,0xF0,0xF0,0xFF,0xFF,0xF0,0xF0,0xF0,0xFF,0xFF,0xFF,0xFF,0xFF,0xF0,0xF0,
0xF0,0xF0,0xF0,0xF8,0xF8,0xF8,0xFF,0xFF,0xF0,0xF0,0xF0,0xF0,0xF1,0xF1,0xF1,0xF1,
0xF1,0xF1,0xF1,0xF0,0xF0,0xF0,0xF0,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,
0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,/*"D:\GD32F303\GD32F30x_Firmware_Library_V2.1.4_iic_oled\记帖.bmp",0*/
/* (64 X 64 )*/

};


#endif

显示图片

		delay_1ms(2000);
		OLED_Clear();  	
		OLED_DrawBMP(0,0,64,8,BMP1);  //图片显示(图片显示慎用，生成的字表较大，会占用较多空间，FLASH空间8K以下慎用)

在这里插入图片描述

OLED.C

//	 
//本程序只供学习使用，未经作者许可，不得用于其它任何用途
//记帖Q群:615061293
//B站视频：https://space.bilibili.com/26152390
//CSDN:https://blog.csdn.net/qq_24312945/
//  文 件 名   : main.c
//  版 本 号   : v2.0
//  作    者   : Evk123
//  生成日期   : 2014-0101
//  最近修改   : 
//  功能描述   : 0.69寸OLED 接口演示例程(STM32F103ZE系列IIC)
//              说明: 
//              ----------------------------------------------------------------
//              GND   电源地
//              VCC   接5V或3.3v电源
//              SCL   接PA5（SCL）
//              SDA   接PA7（SDA）            
//              ----------------------------------------------------------------
//记帖Q群:615061293
//All rights reserved
//
#include "oled.h"
#include "stdlib.h"
#include "oledfont.h"  	 

#include "gd32f30x_i2c.h"
#include "systick.h"
//#include "delay.h"
//OLED的显存
//存放格式如下.
//[0]0 1 2 3 ... 127	
//[1]0 1 2 3 ... 127	
//[2]0 1 2 3 ... 127	
//[3]0 1 2 3 ... 127	
//[4]0 1 2 3 ... 127	
//[5]0 1 2 3 ... 127	
//[6]0 1 2 3 ... 127	
//[7]0 1 2 3 ... 127 			   
/**********************************************
//IIC Start
**********************************************/
/**********************************************
//IIC Start
**********************************************/
//void IIC_Start()
//{

//	OLED_SCLK_Set() ;
//	OLED_SDIN_Set();
//	OLED_SDIN_Clr();
//	OLED_SCLK_Clr();
//}

///**********************************************
IIC Stop
//**********************************************/
//void IIC_Stop()
//{
//OLED_SCLK_Set() ;
	OLED_SCLK_Clr();
//	OLED_SDIN_Clr();
//	OLED_SDIN_Set();
//	
//}

//void IIC_Wait_Ack()
//{

//	//GPIOB->CRH &= 0XFFF0FFFF;	//设置PB12为上拉输入模式
//	//GPIOB->CRH |= 0x00080000;
	OLED_SDA = 1;
	delay_us(1);
//	//OLED_SCL = 1;
//	//delay_us(50000);
///*	while(1)
//	{
//		if(!OLED_SDA)				//判断是否接收到OLED 应答信号
//		{
//			//GPIOB->CRH &= 0XFFF0FFFF;	//设置PB12为通用推免输出模式
//			//GPIOB->CRH |= 0x00030000;
//			return;
//		}
//	}
//*/
//	OLED_SCLK_Set() ;
//	OLED_SCLK_Clr();
//}





/**
  * @brief I2C1写函数
  * @param addr设备地址
  * @param pdata 数据指针
  * @param data_length 数据长度
  */
void i2c_write(uint8_t addr, uint8_t *pdata, uint32_t data_length)
{
    uint32_t i;
    
    /* wait until I2C bus is idle */
    while(i2c_flag_get(I2C1, I2C_FLAG_I2CBSY));//等待总线空闲
    /* send a start condition to I2C bus */
    i2c_start_on_bus(I2C1);//发送start信号
    /* wait until SBSEND bit is set */
    while(!i2c_flag_get(I2C1, I2C_FLAG_SBSEND));    //起始位是否发送
    /* send slave address to I2C bus */
    i2c_master_addressing(I2C1, addr, I2C_TRANSMITTER);//设置从机地址和执行发送操作
    /* wait until ADDSEND bit is set */
    while(!i2c_flag_get(I2C1, I2C_FLAG_ADDSEND));//主机模式下地址是否发送
    /* clear ADDSEND bit */
    i2c_flag_clear(I2C1, I2C_FLAG_ADDSEND);//清除标志位主机模式下地址是否发送
    /* wait until the transmit data buffer is empty */
    while(!i2c_flag_get(I2C1, I2C_FLAG_TBE));//发送期间I2C_DATA为空
    for(i = 0; i < data_length; i++){
        /* data transmission */
        i2c_data_transmit(I2C1, pdata[i]);//发送数据
        /* wait until the TBE bit is set */
        while(!i2c_flag_get(I2C1, I2C_FLAG_TBE));//发送期间I2C_DATA为空
    }
    /* send a stop condition to I2C bus */
    i2c_stop_on_bus(I2C1);//在I2C总线上生成停止位
    /* wait until stop condition generate */ 
    while(I2C_CTL0(I2C1)&0x0200);  //等待直到停止条件生成  
}


/**********************************************
// IIC Write byte
**********************************************/

void Write_IIC_Byte(unsigned char IIC_Byte)
{
//	unsigned char i;
//	unsigned char m,da;
//	da=IIC_Byte;
//	OLED_SCLK_Clr();
//	for(i=0;i<8;i++)		
//	{
//			m=da;
//		//	OLED_SCLK_Clr();
//		m=m&0x80;
//		if(m==0x80)
//		{OLED_SDIN_Set();}
//		else OLED_SDIN_Clr();
//			da=da<<1;
//		OLED_SCLK_Set();
//		OLED_SCLK_Clr();
//		}


uint8_t byte[1] = {};	
byte[0]=IIC_Byte;
i2c_write(0x78,byte, 1);

}




/**********************************************
// IIC Write Command
**********************************************/
void Write_IIC_Command(unsigned char IIC_Command)
{
//   IIC_Start();
//   Write_IIC_Byte(0x78);            //Slave address,SA0=0
//	IIC_Wait_Ack();	
//   Write_IIC_Byte(0x00);			//write command
//	IIC_Wait_Ack();	
//   Write_IIC_Byte(IIC_Command); 
//	IIC_Wait_Ack();	
//   IIC_Stop();

	uint8_t byte[2] = {};	
	byte[0]	=0x00;
	byte[1]	=IIC_Command;	
	i2c_write(0x78,byte, 2);	




}
/**********************************************
// IIC Write Data
**********************************************/
void Write_IIC_Data(unsigned char IIC_Data)
{
//   IIC_Start();
//   Write_IIC_Byte(0x78);			//D/C#=0; R/W#=0
//	IIC_Wait_Ack();	
//   Write_IIC_Byte(0x40);			//write data
//	IIC_Wait_Ack();	
//   Write_IIC_Byte(IIC_Data);
//	IIC_Wait_Ack();	
//   IIC_Stop();
//	 
	 
	uint8_t byte[2] = {};	
	byte[0]	=0x40;
	byte[1]	=IIC_Data;	
	i2c_write(0x78,byte, 2);		 
	 
	 
}
void OLED_WR_Byte(unsigned dat,unsigned cmd)
{
	if(cmd)
			{

   Write_IIC_Data(dat);
   
		}
	else {
   Write_IIC_Command(dat);
		
	}


}


/********************************************
// fill_Picture
********************************************/
void fill_picture(unsigned char fill_Data)
{
	unsigned char m,n;
	for(m=0;m<8;m++)
	{
		OLED_WR_Byte(0xb0+m,0);		//page0-page1
		OLED_WR_Byte(0x00,0);		//low column start address
		OLED_WR_Byte(0x10,0);		//high column start address
		for(n=0;n<128;n++)
			{
				OLED_WR_Byte(fill_Data,1);
			}
	}
}


/***********************Delay****************************************/
void Delay_50ms(unsigned int Del_50ms)
{
	unsigned int m;
	for(;Del_50ms>0;Del_50ms--)
		for(m=6245;m>0;m--);
}

void Delay_1ms(unsigned int Del_1ms)
{
	unsigned char j;
	while(Del_1ms--)
	{	
		for(j=0;j<123;j++);
	}
}

//坐标设置

	void OLED_Set_Pos(unsigned char x, unsigned char y) 
{ 	OLED_WR_Byte(0xb0+y,OLED_CMD);
	OLED_WR_Byte(((x&0xf0)>>4)|0x10,OLED_CMD);
	OLED_WR_Byte((x&0x0f),OLED_CMD); 
}   	  
//开启OLED显示    
void OLED_Display_On(void)
{
	OLED_WR_Byte(0X8D,OLED_CMD);  //SET DCDC命令
	OLED_WR_Byte(0X14,OLED_CMD);  //DCDC ON
	OLED_WR_Byte(0XAF,OLED_CMD);  //DISPLAY ON
}
//关闭OLED显示     
void OLED_Display_Off(void)
{
	OLED_WR_Byte(0X8D,OLED_CMD);  //SET DCDC命令
	OLED_WR_Byte(0X10,OLED_CMD);  //DCDC OFF
	OLED_WR_Byte(0XAE,OLED_CMD);  //DISPLAY OFF
}		   			 
//清屏函数,清完屏,整个屏幕是黑色的!和没点亮一样!!!	  
void OLED_Clear(void)  
{  
	u8 i,n;		    
	for(i=0;i<8;i++)  
	{  
		OLED_WR_Byte (0xb0+i,OLED_CMD);    //设置页地址（0~7）
		OLED_WR_Byte (0x00,OLED_CMD);      //设置显示位置—列低地址
		OLED_WR_Byte (0x10,OLED_CMD);      //设置显示位置—列高地址   
		for(n=0;n<128;n++)OLED_WR_Byte(0,OLED_DATA); 
	} //更新显示
}
void OLED_On(void)  
{  
	u8 i,n;		    
	for(i=0;i<8;i++)  
	{  
		OLED_WR_Byte (0xb0+i,OLED_CMD);    //设置页地址（0~7）
		OLED_WR_Byte (0x00,OLED_CMD);      //设置显示位置—列低地址
		OLED_WR_Byte (0x10,OLED_CMD);      //设置显示位置—列高地址   
		for(n=0;n<128;n++)OLED_WR_Byte(1,OLED_DATA); 
	} //更新显示
}
//在指定位置显示一个字符,包括部分字符
//x:0~127
//y:0~63
//mode:0,反白显示;1,正常显示				 
//size:选择字体 16/12 
void OLED_ShowChar(u8 x,u8 y,u8 chr,u8 Char_Size)
{      	
	unsigned char c=0,i=0;	
		c=chr-' ';//得到偏移后的值			
		if(x>Max_Column-1){x=0;y=y+2;}
		if(Char_Size ==16)
			{
			OLED_Set_Pos(x,y);	
			for(i=0;i<8;i++)
			OLED_WR_Byte(F8X16[c*16+i],OLED_DATA);
			OLED_Set_Pos(x,y+1);
			for(i=0;i<8;i++)
			OLED_WR_Byte(F8X16[c*16+i+8],OLED_DATA);
			}
			else {	
				OLED_Set_Pos(x,y);
				for(i=0;i<6;i++)
				OLED_WR_Byte(F6x8[c][i],OLED_DATA);
				
			}
}
//m^n函数
u32 oled_pow(u8 m,u8 n)
{
	u32 result=1;	 
	while(n--)result*=m;    
	return result;
}				  
//显示2个数字
//x,y :起点坐标	 
//len :数字的位数
//size:字体大小
//mode:模式	0,填充模式;1,叠加模式
//num:数值(0~4294967295);	 		  
void OLED_ShowNum(u8 x,u8 y,u32 num,u8 len,u8 size2)
{         	
	u8 t,temp;
	u8 enshow=0;						   
	for(t=0;t<len;t++)
	{
		temp=(num/oled_pow(10,len-t-1))%10;
		if(enshow==0&&t<(len-1))
		{
			if(temp==0)
			{
				OLED_ShowChar(x+(size2/2)*t,y,' ',size2);
				continue;
			}else enshow=1; 
		 	 
		}
	 	OLED_ShowChar(x+(size2/2)*t,y,temp+'0',size2); 
	}
} 
//显示一个字符号串
void OLED_ShowString(u8 x,u8 y,u8 *chr,u8 Char_Size)
{
	unsigned char j=0;
	while (chr[j]!='\0')
	{		OLED_ShowChar(x,y,chr[j],Char_Size);
			x+=8;
		if(x>120){x=0;y+=2;}
			j++;
	}
}
//显示汉字
void OLED_ShowCHinese(u8 x,u8 y,u8 no)
{      			    
	u8 t,adder=0;
	OLED_Set_Pos(x,y);	
    for(t=0;t<16;t++)
		{
				OLED_WR_Byte(Hzk[2*no][t],OLED_DATA);
				adder+=1;
     }	
		OLED_Set_Pos(x,y+1);	
    for(t=0;t<16;t++)
			{	
				OLED_WR_Byte(Hzk[2*no+1][t],OLED_DATA);
				adder+=1;
      }					
}
/***********功能描述：显示显示BMP图片128×64起始点坐标(x,y),x的范围0～127，y为页的范围0～7*****************/
void OLED_DrawBMP(unsigned char x0, unsigned char y0,unsigned char x1, unsigned char y1,unsigned char BMP[])
{ 	
 unsigned int j=0;
 unsigned char x,y;
  
  if(y1%8==0) y=y1/8;      
  else y=y1/8+1;
	for(y=y0;y<y1;y++)
	{
		OLED_Set_Pos(x0,y);
    for(x=x0;x<x1;x++)
	    {      
	    	OLED_WR_Byte(BMP[j++],OLED_DATA);	    	
	    }
	}
} 

//初始化SSD1306					    
void OLED_Init(void)
{ 	
 
 	 

 	 
// 	GPIO_InitTypeDef  GPIO_InitStructure;
// 	

//	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);	 //使能A端口时钟
//	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5|GPIO_Pin_7;	 
// 	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP; 		 //推挽输出
//	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;//速度50MHz
// 	GPIO_Init(GPIOA, &GPIO_InitStructure);	  //初始化GPIOD3,6
// 	GPIO_SetBits(GPIOA,GPIO_Pin_5|GPIO_Pin_7);	


//delay_ms(800);
delay_1ms(800);


OLED_WR_Byte(0xAE,OLED_CMD);//--display off
	OLED_WR_Byte(0x00,OLED_CMD);//---set low column address
	OLED_WR_Byte(0x10,OLED_CMD);//---set high column address
	OLED_WR_Byte(0x40,OLED_CMD);//--set start line address  
	OLED_WR_Byte(0xB0,OLED_CMD);//--set page address
	OLED_WR_Byte(0x81,OLED_CMD); // contract control
	OLED_WR_Byte(0xFF,OLED_CMD);//--128   
	OLED_WR_Byte(0xA1,OLED_CMD);//set segment remap 
	OLED_WR_Byte(0xA6,OLED_CMD);//--normal / reverse
	OLED_WR_Byte(0xA8,OLED_CMD);//--set multiplex ratio(1 to 64)
	OLED_WR_Byte(0x3F,OLED_CMD);//--1/32 duty
	OLED_WR_Byte(0xC8,OLED_CMD);//Com scan direction
	OLED_WR_Byte(0xD3,OLED_CMD);//-set display offset
	OLED_WR_Byte(0x00,OLED_CMD);//
	
	OLED_WR_Byte(0xD5,OLED_CMD);//set osc division
	OLED_WR_Byte(0x80,OLED_CMD);//
	
	OLED_WR_Byte(0xD8,OLED_CMD);//set area color mode off
	OLED_WR_Byte(0x05,OLED_CMD);//
	
	OLED_WR_Byte(0xD9,OLED_CMD);//Set Pre-Charge Period
	OLED_WR_Byte(0xF1,OLED_CMD);//
	
	OLED_WR_Byte(0xDA,OLED_CMD);//set com pin configuartion
	OLED_WR_Byte(0x12,OLED_CMD);//
	
	OLED_WR_Byte(0xDB,OLED_CMD);//set Vcomh
	OLED_WR_Byte(0x30,OLED_CMD);//
	
	OLED_WR_Byte(0x8D,OLED_CMD);//set charge pump enable
	OLED_WR_Byte(0x14,OLED_CMD);//
	
	OLED_WR_Byte(0xAF,OLED_CMD);//--turn on oled panel
}

OLED.h

//	 
//本程序只供学习使用，未经作者许可，不得用于其它任何用途

//
//  文 件 名   : main.c
//  版 本 号   : v2.0
//  作    者   : Evk123
//  生成日期   : 2014-0101
//  最近修改   : 
//  功能描述   : 0.69寸OLED 接口演示例程(STM32F103ZE系列IIC)
//              说明: 
//              ----------------------------------------------------------------
//              GND   电源地
//              VCC   接5V或3.3v电源
//              SCL   接PA5（SCL）
//              SDA   接PA7（SDA）            
//              ----------------------------------------------------------------
//记帖Q群:615061293
//B站视频：https://space.bilibili.com/26152390
//CSDN:https://blog.csdn.net/qq_24312945/
//All rights reserved
//
#ifndef __OLED_H
#define __OLED_H			  	 
//#include "sys.h"
#include "stdlib.h"	 
#include "stdint.h"	
   	
#define OLED_MODE 0
#define SIZE 8
#define XLevelL		0x00
#define XLevelH		0x10
#define Max_Column	128
#define Max_Row		64
#define	Brightness	0xFF 
#define X_WIDTH 	128
#define Y_WIDTH 	64	  




  						  
//-----------------OLED IIC端口定义----------------  					   

//#define OLED_SCLK_Clr() GPIO_ResetBits(GPIOA,GPIO_Pin_5)//SCL
//#define OLED_SCLK_Set() GPIO_SetBits(GPIOA,GPIO_Pin_5)

//#define OLED_SDIN_Clr() GPIO_ResetBits(GPIOA,GPIO_Pin_7)//SDA
//#define OLED_SDIN_Set() GPIO_SetBits(GPIOA,GPIO_Pin_7)

 		     
#define OLED_CMD  0	//写命令
#define OLED_DATA 1	//写数据


typedef unsigned          char u8;
typedef unsigned           int u32;

//OLED控制用函数
void OLED_WR_Byte(unsigned dat,unsigned cmd);  
void OLED_Display_On(void);
void OLED_Display_Off(void);	   							   		    
void OLED_Init(void);
void OLED_Clear(void);
void OLED_DrawPoint(u8 x,u8 y,u8 t);
void OLED_Fill(u8 x1,u8 y1,u8 x2,u8 y2,u8 dot);
void OLED_ShowChar(u8 x,u8 y,u8 chr,u8 Char_Size);
void OLED_ShowNum(u8 x,u8 y,u32 num,u8 len,u8 size);
void OLED_ShowString(u8 x,u8 y, u8 *p,u8 Char_Size);	 
void OLED_Set_Pos(unsigned char x, unsigned char y);
void OLED_ShowCHinese(u8 x,u8 y,u8 no);
void OLED_DrawBMP(unsigned char x0, unsigned char y0,unsigned char x1, unsigned char y1,unsigned char BMP[]);
void Delay_50ms(unsigned int Del_50ms);
void Delay_1ms(unsigned int Del_1ms);
void fill_picture(unsigned char fill_Data);
//void Picture();
//void IIC_Start();
//void IIC_Stop();
void Write_IIC_Command(unsigned char IIC_Command);
void Write_IIC_Data(unsigned char IIC_Data);
void Write_IIC_Byte(unsigned char IIC_Byte);

//void IIC_Wait_Ack();




void i2c_write(uint8_t addr, uint8_t *pdata, uint32_t data_length);

#endif

OLEDFONT.H

#ifndef __OLEDFONT_H
#define __OLEDFONT_H 	   
//常用ASCII表
//偏移量32
//ASCII字符集
//偏移量32
//大小:12*6
/************************************6*8的点阵************************************/
const unsigned char F6x8[][6] =		
{
0x00, 0x00, 0x00, 0x00, 0x00, 0x00,// sp
0x00, 0x00, 0x00, 0x2f, 0x00, 0x00,// !
0x00, 0x00, 0x07, 0x00, 0x07, 0x00,// "
0x00, 0x14, 0x7f, 0x14, 0x7f, 0x14,// #
0x00, 0x24, 0x2a, 0x7f, 0x2a, 0x12,// $
0x00, 0x62, 0x64, 0x08, 0x13, 0x23,// %
0x00, 0x36, 0x49, 0x55, 0x22, 0x50,// &
0x00, 0x00, 0x05, 0x03, 0x00, 0x00,// '
0x00, 0x00, 0x1c, 0x22, 0x41, 0x00,// (
0x00, 0x00, 0x41, 0x22, 0x1c, 0x00,// )
0x00, 0x14, 0x08, 0x3E, 0x08, 0x14,// *
0x00, 0x08, 0x08, 0x3E, 0x08, 0x08,// +
0x00, 0x00, 0x00, 0xA0, 0x60, 0x00,// ,
0x00, 0x08, 0x08, 0x08, 0x08, 0x08,// -
0x00, 0x00, 0x60, 0x60, 0x00, 0x00,// .
0x00, 0x20, 0x10, 0x08, 0x04, 0x02,// /
0x00, 0x3E, 0x51, 0x49, 0x45, 0x3E,// 0
0x00, 0x00, 0x42, 0x7F, 0x40, 0x00,// 1
0x00, 0x42, 0x61, 0x51, 0x49, 0x46,// 2
0x00, 0x21, 0x41, 0x45, 0x4B, 0x31,// 3
0x00, 0x18, 0x14, 0x12, 0x7F, 0x10,// 4
0x00, 0x27, 0x45, 0x45, 0x45, 0x39,// 5
0x00, 0x3C, 0x4A, 0x49, 0x49, 0x30,// 6
0x00, 0x01, 0x71, 0x09, 0x05, 0x03,// 7
0x00, 0x36, 0x49, 0x49, 0x49, 0x36,// 8
0x00, 0x06, 0x49, 0x49, 0x29, 0x1E,// 9
0x00, 0x00, 0x36, 0x36, 0x00, 0x00,// :
0x00, 0x00, 0x56, 0x36, 0x00, 0x00,// ;
0x00, 0x08, 0x14, 0x22, 0x41, 0x00,// <
0x00, 0x14, 0x14, 0x14, 0x14, 0x14,// =
0x00, 0x00, 0x41, 0x22, 0x14, 0x08,// >
0x00, 0x02, 0x01, 0x51, 0x09, 0x06,// ?
0x00, 0x32, 0x49, 0x59, 0x51, 0x3E,// @
0x00, 0x7C, 0x12, 0x11, 0x12, 0x7C,// A
0x00, 0x7F, 0x49, 0x49, 0x49, 0x36,// B
0x00, 0x3E, 0x41, 0x41, 0x41, 0x22,// C
0x00, 0x7F, 0x41, 0x41, 0x22, 0x1C,// D
0x00, 0x7F, 0x49, 0x49, 0x49, 0x41,// E
0x00, 0x7F, 0x09, 0x09, 0x09, 0x01,// F
0x00, 0x3E, 0x41, 0x49, 0x49, 0x7A,// G
0x00, 0x7F, 0x08, 0x08, 0x08, 0x7F,// H
0x00, 0x00, 0x41, 0x7F, 0x41, 0x00,// I
0x00, 0x20, 0x40, 0x41, 0x3F, 0x01,// J
0x00, 0x7F, 0x08, 0x14, 0x22, 0x41,// K
0x00, 0x7F, 0x40, 0x40, 0x40, 0x40,// L
0x00, 0x7F, 0x02, 0x0C, 0x02, 0x7F,// M
0x00, 0x7F, 0x04, 0x08, 0x10, 0x7F,// N
0x00, 0x3E, 0x41, 0x41, 0x41, 0x3E,// O
0x00, 0x7F, 0x09, 0x09, 0x09, 0x06,// P
0x00, 0x3E, 0x41, 0x51, 0x21, 0x5E,// Q
0x00, 0x7F, 0x09, 0x19, 0x29, 0x46,// R
0x00, 0x46, 0x49, 0x49, 0x49, 0x31,// S
0x00, 0x01, 0x01, 0x7F, 0x01, 0x01,// T
0x00, 0x3F, 0x40, 0x40, 0x40, 0x3F,// U
0x00, 0x1F, 0x20, 0x40, 0x20, 0x1F,// V
0x00, 0x3F, 0x40, 0x38, 0x40, 0x3F,// W
0x00, 0x63, 0x14, 0x08, 0x14, 0x63,// X
0x00, 0x07, 0x08, 0x70, 0x08, 0x07,// Y
0x00, 0x61, 0x51, 0x49, 0x45, 0x43,// Z
0x00, 0x00, 0x7F, 0x41, 0x41, 0x00,// [
0x00, 0x55, 0x2A, 0x55, 0x2A, 0x55,// 55
0x00, 0x00, 0x41, 0x41, 0x7F, 0x00,// ]
0x00, 0x04, 0x02, 0x01, 0x02, 0x04,// ^
0x00, 0x40, 0x40, 0x40, 0x40, 0x40,// _
0x00, 0x00, 0x01, 0x02, 0x04, 0x00,// '
0x00, 0x20, 0x54, 0x54, 0x54, 0x78,// a
0x00, 0x7F, 0x48, 0x44, 0x44, 0x38,// b
0x00, 0x38, 0x44, 0x44, 0x44, 0x20,// c
0x00, 0x38, 0x44, 0x44, 0x48, 0x7F,// d
0x00, 0x38, 0x54, 0x54, 0x54, 0x18,// e
0x00, 0x08, 0x7E, 0x09, 0x01, 0x02,// f
0x00, 0x18, 0xA4, 0xA4, 0xA4, 0x7C,// g
0x00, 0x7F, 0x08, 0x04, 0x04, 0x78,// h
0x00, 0x00, 0x44, 0x7D, 0x40, 0x00,// i
0x00, 0x40, 0x80, 0x84, 0x7D, 0x00,// j
0x00, 0x7F, 0x10, 0x28, 0x44, 0x00,// k
0x00, 0x00, 0x41, 0x7F, 0x40, 0x00,// l
0x00, 0x7C, 0x04, 0x18, 0x04, 0x78,// m
0x00, 0x7C, 0x08, 0x04, 0x04, 0x78,// n
0x00, 0x38, 0x44, 0x44, 0x44, 0x38,// o
0x00, 0xFC, 0x24, 0x24, 0x24, 0x18,// p
0x00, 0x18, 0x24, 0x24, 0x18, 0xFC,// q
0x00, 0x7C, 0x08, 0x04, 0x04, 0x08,// r
0x00, 0x48, 0x54, 0x54, 0x54, 0x20,// s
0x00, 0x04, 0x3F, 0x44, 0x40, 0x20,// t
0x00, 0x3C, 0x40, 0x40, 0x20, 0x7C,// u
0x00, 0x1C, 0x20, 0x40, 0x20, 0x1C,// v
0x00, 0x3C, 0x40, 0x30, 0x40, 0x3C,// w
0x00, 0x44, 0x28, 0x10, 0x28, 0x44,// x
0x00, 0x1C, 0xA0, 0xA0, 0xA0, 0x7C,// y
0x00, 0x44, 0x64, 0x54, 0x4C, 0x44,// z
0x14, 0x14, 0x14, 0x14, 0x14, 0x14,// horiz lines
};
/****************************************8*16的点阵************************************/
const unsigned char F8X16[]=	  
{
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,// 0
  0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00,//! 1
  0x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//" 2
  0x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00,//# 3
  0x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00,//$ 4
  0xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00,//% 5
  0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10,//& 6
  0x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//' 7
  0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00,//( 8
  0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00,//) 9
  0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00,//* 10
  0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00,//+ 11
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00,//, 12
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//- 13
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,//. 14
  0x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00,/// 15
  0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,//0 16
  0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//1 17
  0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,//2 18
  0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00,//3 19
  0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00,//4 20
  0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,//5 21
  0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00,//6 22
  0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,//7 23
  0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00,//8 24
  0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00,//9 25
  0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,//: 26
  0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00,//; 27
  0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00,//< 28
  0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00,//= 29
  0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00,//> 30
  0x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00,//? 31
  0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00,//@ 32
  0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,//A 33
  0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,//B 34
  0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00,//C 35
  0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00,//D 36
  0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00,//E 37
  0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00,//F 38
  0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00,//G 39
  0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20,//H 40
  0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//I 41
  0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00,//J 42
  0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00,//K 43
  0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00,//L 44
  0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00,//M 45
  0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00,//N 46
  0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00,//O 47
  0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00,//P 48
  0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00,//Q 49
  0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20,//R 50
  0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00,//S 51
  0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//T 52
  0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//U 53
  0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,//V 54
  0xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00,//W 55
  0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20,//X 56
  0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//Y 57
  0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00,//Z 58
  0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00,//[ 59
  0x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00,//\ 60
  0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00,//] 61
  0x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^ 62
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,//_ 63
  0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//` 64
  0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,//a 65
  0x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00,//b 66
  0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,//c 67
  0x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20,//d 68
  0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,//e 69
  0x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//f 70
  0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00,//g 71
  0x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//h 72
  0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//i 73
  0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,//j 74
  0x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00,//k 75
  0x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//l 76
  0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,//m 77
  0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//n 78
  0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//o 79
  0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00,//p 80
  0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80,//q 81
  0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00,//r 82
  0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00,//s 83
  0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,//t 84
  0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20,//u 85
  0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00,//v 86
  0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,//w 87
  0x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00,//x 88
  0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00,//y 89
  0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00,//z 90
  0x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40,//{ 91
  0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,//| 92
  0x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00,//} 93
  0x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//~ 94
};
char Hzk[][32]={

// 记(0) 帖(1) 年(2) 月(3) 日(4)

{0x40,0x40,0x42,0xCC,0x00,0x00,0x00,0x84,0x84,0x84,0x84,0x84,0xFC,0x00,0x00,0x00},
{0x00,0x00,0x00,0x7F,0x20,0x10,0x00,0x3F,0x40,0x40,0x40,0x40,0x41,0x40,0x70,0x00},/*"记",0*/
/* (16 X 16 , 宋体 )*/

{0x00,0xF8,0x08,0xFF,0x08,0xF8,0x00,0x00,0x00,0x00,0xFF,0x10,0x10,0x10,0x10,0x00},
{0x00,0x0F,0x00,0xFF,0x08,0x0F,0x00,0xFF,0x41,0x41,0x41,0x41,0x41,0xFF,0x00,0x00},/*"帖",1*/
/* (16 X 16 , 宋体 )*/

{0x00,0x20,0x18,0xC7,0x44,0x44,0x44,0x44,0xFC,0x44,0x44,0x44,0x44,0x04,0x00,0x00},
{0x04,0x04,0x04,0x07,0x04,0x04,0x04,0x04,0xFF,0x04,0x04,0x04,0x04,0x04,0x04,0x00},/*"年",2*/
/* (16 X 16 , 宋体 )*/

{0x00,0x00,0x00,0xFE,0x22,0x22,0x22,0x22,0x22,0x22,0x22,0x22,0xFE,0x00,0x00,0x00},
{0x80,0x40,0x30,0x0F,0x02,0x02,0x02,0x02,0x02,0x02,0x42,0x82,0x7F,0x00,0x00,0x00},/*"月",3*/
/* (16 X 16 , 宋体 )*/

{0x00,0x00,0x00,0xFE,0x82,0x82,0x82,0x82,0x82,0x82,0x82,0xFE,0x00,0x00,0x00,0x00},
{0x00,0x00,0x00,0xFF,0x40,0x40,0x40,0x40,0x40,0x40,0x40,0xFF,0x00,0x00,0x00,0x00},/*"日",4*/
/* (16 X 16 , 宋体 )*/


};

#endif

以上的代码会在Q_qun里分享。QQ_qun：615061293。
或者关注『记帖』，持续更新文章和学习资料!
在这里插入图片描述

记帖
关注
  • 9
    点赞
  • 踩
  • 28
    收藏
    觉得还不错? 一键收藏
  • 打赏
    打赏
  • 6
    评论
专栏目录
GD32F303通过模拟IIC驱动OLED 采集并显示各种常见类目 多级菜单、图片、文字、字母（测试可行）
12-13
通过GD32F303MCU 利用模拟IIC驱动OLED和SHT30,将采集的数据显示在屏幕上.
【GD32】从0开始学GD32单片机（8）—— I2C外设详解+主机从机发送和接收例程
JackieCoo的博客
09-25 9527
介绍GD32的I2C外设，包含主机从机发送和接收例程
I2C总线时序图： 8位设备地址 16位寄存器地址 16位数据
yhy08090的博客
05-09 9079
有关I2C总线时序，下面的文章写得很好，推荐阅读 https://www.cnblogs.com/BitArt/archive/2013/05/28/3103917.html#commentform 8位设备地址，8位寄存器地址，8位数据的情况完全够了 下面我想补充的是8位设备地址，16位寄存器地址，16位数据的传输时序，如下： ...
i2c-tools读写16位寄存器调试
aa112901a的博客
04-04 1万+
最近在rk3399平台上更换调试了录音小板，原rk3399的es7243 修改新的adc小板，一开始硬件就有问题，但因为对硬件不熟悉，导致做了汗多无用功， 言归正传，换adc录音小板，首先应该用i2ctools 检测寄存器 硬件i2c ok的情况下能使用i2cdetect 能检测到设备，驱动里配置了地址就显示为UU，没有配置地址显示具体值，比如10 一般寄存器都...
GD32F303调试小记(三)之IIC(硬件IIC+PCF8563实时时钟)
欢喜6666的博客
11-15 1万+
前言 前面的文章介绍了在单片机中常用的两种串口通信协议(USART和SPI)，并给出了GD32F303对应的配置流程。这次介绍第三种常见的串口通信协议IIC。 IIC IIC，又名I2C，也是一种串口通信协议。其中包含一根时钟线和一根数据线。 ...
小熊派gd32f303学习之旅（8）— 使用软件模拟I2C读写EEPROM
qq_38113006的博客
10-08 5490
小熊派gd32f303学习之旅（8）— 使用软件模拟I2C读写EEPROM 一、前言 IIC是一种非常常用的低速通信总线，广泛被用于连接微控制器及其外围设备。 关于IIC的介绍可以参考：IIC通信协议详解 这里我们用软件模拟 IIC来读写AT24C02这个EEPROM。芯片AT24C02的总容量是 256 个字节，该芯片通过 IIC 总线与外部连接。 如下所示，是E53_SC1拓展板上AT24C02的硬件连接图，不过这里有一个很大的问题，就是通过其地址设置引脚的接线我们得到其7位地址为0x51，可实际上，三
GD32F303固件库开发
04-24
GD32F303固件库开发由于STM32芯片的费用不断的上升，很多小伙伴都开始做找替代芯片。我们采用兆易创新的GD32F303，记录整个从硬件到软件设计，大家可以持续关注学习。学会使用GD32F303固件包进行开发，使用环境为Keil。使用芯片为GD32F303,是STM32F103的升级版。学完可以对STM32F103切换为GD32F303。  
STM32CUBEMX开发GD32F303（14）----IIC之配置OLED
热门推荐
xh1479的博客
09-18 1万+
本章STM32CUBEMX配置STM32F103，并且在GD32F303中进行开发，同时通过开发板内进行验证。使用IIC进行驱动SSD1306的12864OLED。
GD32f303的硬件IIC.从机配置与接收流程
time_grid的博客
07-11 7267
1、要注意硬件IIC配置相当坑，看起来没关系的两个函数，只要初始化配置化调用写反了就可能导致问题。比如：最终使能IIC的函数< i2c_enable(I2Cx) >与配置应答的函数< i2c_ack_config(I2Cx, I2C_ACK_ENABLE) >写反了就会导致配置失败。非常离谱。 2、在写自己的中断函数时要注意好逻辑，从机发与从机收是两个套路。而且< i2c_interrupt_flag_clear() >函数不是万能的。要注意这个函数只能清除哪些标志位。二、我的硬件IIc.从机
21_GD32F103_I2C_EEPROM.rar
05-26
使用硬件I2C0读写EEPROM
GD32硬件IIC+DMA程序
01-11
GD32硬件IIC+DMA程序，使用的IIC时序如下。 写寄存器操作为： START+ACK（从机的ACK信号）+IIC设备地址+（从机的ACK信号）+START+ACK（从机的ACK信号）+IIC写寄存器地址+ACK（从机的ACK信号）+IIC写数据（4Byte，每个数据后都有ACK）+STOP 读寄存器操作为： START+ACK（从机的ACK信号）+IIC设备地址+（从机的ACK信号）+START+ACK（从机的ACK信号）+IIC读寄存器地址+ACK（从机的ACK信号）+IIC读数据（4Byte，前n个数据后都有（主机发送的）ACK,最后1byte数据后如果发ACK，表示还有数据要读，如果最后1byte数据后为NACK，后面紧接着就是停止位）+STOP
基于STM32F407--OLED--两线IIC显示
04-18
基于正点原子的IIC与OLED 显示，只需要两个接口即可，一根数据线，一根时钟线，内有如何将SPI-OLED改成IIC-OLED ，电路简单，代码少如即可点亮，还有汉字函数！
STM32F103,GD32F3XX等CPU硬件/软件操作IIC（24C01-64）程序
08-10
适用于STM32F103,GD32F3XX等CPU，通过宏定义选择硬件/软件操作IIC（24C01-64）。采用keil标准库，解决了标准库的一些BUG。很多类似资源都不全面，甚至不可用，此程序亲测可用，稳定可靠，对遇到硬件操作IIC问题的...
IIC_LCD1602 STM32-HAL驱动程序-硬件IIC
11-11
STM32F103C8T6驱动LCD(带PCF8574转接板，IIC驱动)，利用CUBEMAX生成，HAL库硬件IIC.
STC15驱动IIC-OLED.rar
11-09
STC15驱动IIC-OLED程序
小熊派gd32f303学习之旅（9）— 使用硬件I2C读写EEPROM
qq_38113006的博客
10-11 7221
小熊派gd32f303学习之旅（9）— 使用硬件I2C读写EEPROM 一、前言 在上一篇中，我们使用软件模拟IIC对AT24C02进行了读写，通过查看GD32F30X的参考手册可以知道，其有2个硬件IIC控制器，现在我们就尝试使用其硬件IIC进行对AT24C02的读写。 查看小熊派的原理图，确定AT24C02其使用的IIC引脚为SCL->PB6、SDA->PB7 查看数据手册可以知道这两个引脚被I2C0控制器复用为I2C引脚了，那么就可以满足我们的使用需求了 二、初始化I2C0控制器 如下
GD32F303移植4针0.96寸OLED显示屏（I2C）
陈师傅的博客
04-03 1140
本文讲解如何在GD32F303中移植0.96寸OLED显示屏
GD32F103硬件I2C0通讯
weixin_42550185的博客
08-08 2140
GD32F103硬件I2C0通讯.
gd32f303固件库开发
最新发布
08-13
GD32F303固件库开发是指使用GD32F303系列芯片进行软件开发的过程。该系列芯片具有丰富的外设资源和强大的性能，可以广泛应用于各种嵌入式系统开发中。 在GD32F303固件库开发中，可以利用官方提供的固件库和开发工具进行软件开发。可以通过前期准备与烧录、GPIO输入输出、USART通信、ADC采集、PWM输出、定时器等功能来实现各种应用需求。 在前期准备与烧录阶段，需要准备好开发环境，并将固件库烧录到芯片中。之后可以根据需要使用GPIO进行输入输出操作，使用USART进行数据收发，使用ADC进行模拟信号采集，使用PWM输出控制电机或灯光，使用定时器进行定时任务的实现等。 在GD32的官方网站和一些技术博客上可以找到大量的DEMO文件和教程，这些资源可以帮助开发者更好地理解和应用GD32F303固件库。 总之，GD32F303固件库开发提供了丰富的外设资源和强大的性能，可以满足各种嵌入式系统的开发需求。开发者可以根据具体的应用需求，使用固件库和相应的开发工具进行软件开发。<span class="em">1</span><span class="em">2</span><span class="em">3</span> #### 引用[.reference_title] - *1* *2* *3* [GD32F303固件库开发](https://blog.csdn.net/qq_24312945/article/details/127648981)[target="_blank" data-report-click={"spm":"1018.2226.3001.9630","extra":{"utm_source":"vip_chatgpt_common_search_pc_result","utm_medium":"distribute.pc_search_result.none-task-cask-2~all~insert_cask~default-1-null.142^v92^chatsearchT3_1"}}] [.reference_item style="max-width: 100%"] [ .reference_list ]

“相关推荐”对你有帮助么？

  • 非常没帮助
  • 没帮助
  • 一般
  • 有帮助
  • 非常有帮助
提交
评论 6
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付：10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包

打赏作者

记帖

你的鼓励将是我创作的最大动力

¥1 ¥2 ¥4 ¥6 ¥10 ¥20
扫码支付：¥1
获取中
扫码支付

您的余额不足，请更换扫码支付或充值

打赏作者

实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明：

1.余额是钱包充值的虚拟货币，按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载，可以购买VIP、付费专栏及课程。

余额充值