H3C交换机配置实验-交换机堆叠（IRF）+二层LACP聚合+vlan间互通实验

实验拓扑：

需求： 

SW1和SW2做堆叠，分别上联到SW3交换机，vlan网关写在SW3上，使PC1跟PC2能够互通 

实验步骤 

sw1跟sw2先配置堆叠 

1.修改SW2的irf member，重启生效 

[SW2]irf member 1 renumber 2           #修改SW2的irf member为2
[SW2]quit
[SW2]reboot

 2、SW1、SW2分别将IRF物理口shutdown，按照规划加入IRF-PORT。

sw1
[SW1]interface range Ten-GigabitEthernet 1/0/49 to Ten-GigabitEthernet 1/0/50

[SW1-if-range]shutdown
[SW1-if-range]quit
[SW1]irf-port 1/1
[SW1-irf-port1/1]port group interface Ten-GigabitEthernet 1/0/49
[SW1-irf-port1/1]port group interface Ten-GigabitEthernet 1/0/50

sw2
[SW2]interface range Ten-GigabitEthernet 2/0/49 to Ten-GigabitEthernet 2/0/50

[SW2-if-range]shutdown
[SW2-if-range]quit
[SW2]irf-port 2/2
[SW2-irf-port2/2]port group interface Ten-GigabitEthernet 2/0/49
[SW2-irf-port2/2]port group interface Ten-GigabitEthernet 2/0/50

3、SW1、SW2分别将IRF物理口undo shutdown，并保存配置.

SW1配置如下：
[SW1]interface range Ten-GigabitEthernet 1/0/49 to Ten-GigabitEthernet 1/0/52
[SW1]undo shutdown
[SW1]quit
[SW1]save

SW2配置如下：
[SW2]interface range Ten-GigabitEthernet 2/0/49 to Ten-GigabitEthernet 2/0/52
[SW2]undo shutdown
[SW2]quit
[SW2]save

4、SW1、SW2分别激活IRF配置。

2台交换机分别执行以下命令激活配置 

irf-port-configuration active                   #激活IRF配置

 5.验证堆叠配置结果

[SW1]dis irf link

[SW1]dis irf 

6.SW3交换机配置vlan及vlan接口地址，并将连接sw1跟sw2的47跟48口配置lacp,trunk，SW1上1/0/48跟2/0/48同样做lacp，都配置成trunk,放行所有vlan 

sw3上配置如下：
[SW3]vlan 10
[SW3-vlan10]quit
[SW3]vlan 20
[SW3-vlan20]quit
[SW3]interface Vlan-interface 10
[SW3-Vlan-interface10]ip address 192.168.10.254 255.255.255.0
[SW3-Vlan-interface10]quit
[SW3-Vlan-interface20]ip address 192.168.20.254 255.255.255.0
[SW3-Vlan-interface20]quit
[SW3]interface Bridge-Aggregation 24               #创建聚合口24
[SW3-Bridge-Aggregation24]]port link-type trunk                                  #将聚合口设置为trunk
[SW3-Bridge-Aggregation24]] port trunk permit vlan all                        #允许所有vlan通过
[SW3-Bridge-Aggregation24]]link-aggregation mode dynamic             #聚合模式为动态聚合
[SW3]interface range GigabitEthernet1/0/47  to  GigabitEthernet1/0/48        #进入到交换机1/0/47跟1/0/48口
[SW3-if-range]]port link-mode bridge                              # 设置链路模式为二层以太网              
[SW3-if-range]] port link-type trunk                                  #端口类型为trunk
[SW3-if-range]]port trunk permit vlan all                         #允许所有vlan通过
 
[SW3-if-range]] port link-aggregation group 24              #将2个端口加入到聚合组1

 查看vlan及接口配置

 查看接口47和48

查看聚合口 

 sw1上配置如下：

 [SW1]interface Bridge-Aggregation 48                                 #sw1上创建聚合口24
 [SW1-Bridge-Aggregation48]]port link-type trunk                                  #将聚合口设置为trunk
 [SW1-Bridge-Aggregation48]] port trunk permit vlan all                        #允许所有vlan通过
 [SW1-Bridge-Aggregation48]]link-aggregation mode dynamic             #聚合模式为动态聚合
 [SW1-Bridge-Aggregation48]]mad enable                                            #开启mad检测，防止堆叠脑裂
 [SW1]interface  GigabitEthernet1/0/48                             #进入到交换机1/0/48口
 [SW1-if-range]]port link-mode bridge                              # 设置链路模式为二层以太网              
 [SW1-if-range]] port link-type trunk                                  #端口类型为trunk
 [SW1-if-range]]port trunk permit vlan all                         #允许所有vlan通过
 
 [SW1-if-range]] port link-aggregation group 48             #将2个端口加入到聚合组48
 [SW1]interface  GigabitEthernet2/0/48                             #进入到交换机2/0/48口
 [SW1-if-range]]port link-mode bridge                              # 设置链路模式为二层以太网              
 [SW1-if-range]] port link-type trunk                                  #端口类型为trunk
 [SW1-if-range]]port trunk permit vlan all                         #允许所有vlan通过
 
 [SW1-if-range]] port link-aggregation group 48             #将2个端口加入到聚合组48
 [SW1]interface Bridge-Aggregation 48                             #进入聚合口48
 [SW1-Bridge-Aggregation48]]mad enable                                            #开启mad lacp 检测，防止堆叠脑裂  ，需要注意的是之前聚合口已经做了lacp聚合，所以mad检测也只能是lacp,也可以单独在两台交换机之间接一根线，专门配置BFD检测

看到以下图片中sw1跟sw3聚合口速率为2G，说明两端聚合配置成功，2个千兆口做的聚合 

 

7.sw1上配置vlan 10 和vlan20，并将1/0/1加入到vlan10，2/0/1加入到vlan20 

[SW1]vlan 10
[SW1-vlan10]quit
[SW1]vlan 20
[SW1-vlan20]quit
[SW1]interface GigabitEthernet 1/0/1
[SW1-GigabitEthernet1/0/1]port access vlan 10
[SW1-GigabitEthernet1/0/1]quit
[SW1]interface GigabitEthernet 2/0/1
[SW1-GigabitEthernet2/0/1]port access vlan 20
[SW1-GigabitEthernet2/0/1]quit

8.PC配置相应IP地址，进行互通验证 

 

PC1ping vlan10跟vlan20的网关 

 PC1ping PC2的IP