imx6Q/6dl的GPIO宏定义

imx6dl的管脚定义

其IO口宏定义在\arch\arm\plat-mxc\include\mach\iomux-mx6dl.h中，如CSI0_DAT10的定义。

/*管脚模式的命名规则为：MX6Q_PAD_<padname>__<padmode>_  padname为管脚名，padmode为管脚模式。*/
#define MX6DL_PAD_CSI0_DAT10__IPU1_CSI0_D_10                                   \
		IOMUX_PAD(0x0360, 0x004C, 0, 0x0000, 0, NO_PAD_CTRL)
#define MX6DL_PAD_CSI0_DAT10__AUDMUX_AUD3_RXC                                  \
		IOMUX_PAD(0x0360, 0x004C, 1, 0x0000, 0, NO_PAD_CTRL)
#define MX6DL_PAD_CSI0_DAT10__ECSPI2_MISO                                      \
		IOMUX_PAD(0x0360, 0x004C, 2, 0x07F8, 0, MX6DL_ECSPI_PAD_CTRL)
#define MX6DL_PAD_CSI0_DAT10__UART1_TXD                                        \
		IOMUX_PAD(0x0360, 0x004C, 3, 0x0000, 0, MX6DL_UART_PAD_CTRL)
#define MX6DL_PAD_CSI0_DAT10__UART1_RXD                                        \
		IOMUX_PAD(0x0360, 0x004C, 3, 0x08FC, 0, MX6DL_UART_PAD_CTRL)
#define MX6DL_PAD_CSI0_DAT10__SDMA_DEBUG_PC_4                                  \
		IOMUX_PAD(0x0360, 0x004C, 4, 0x0000, 0, NO_PAD_CTRL)
#define MX6DL_PAD_CSI0_DAT10__GPIO_5_28                                        \
		IOMUX_PAD(0x0360, 0x004C, 5, 0x0000, 0, NO_PAD_CTRL)
#define MX6DL_PAD_CSI0_DAT10__MMDC_MMDC_DEBUG_33                               \
		IOMUX_PAD(0x0360, 0x004C, 6, 0x0000, 0, NO_PAD_CTRL)
#define MX6DL_PAD_CSI0_DAT10__SIMBA_TRACE_7                                    \
		IOMUX_PAD(0x0360, 0x004C, 7, 0x0000, 0, NO_PAD_CTRL)

具体的可参考EthanYYYY的博客

board-mx6q_sabresd.c

在iomux-mx6dl.h定义的宏定义最终会在board-mx6q_sabresd.c进行调用。	

static void __init mx6_sabresd_board_init(void)
{
	int i;
	int ret;
	struct clk *clko2;
	struct clk *new_parent;
	int rate;
     /*判断ｃｐｕ类型和ｐａｄ初始化*/
	if (cpu_is_mx6q())
		mxc_iomux_v3_setup_multiple_pads(mx6q_sabresd_pads,
			ARRAY_SIZE(mx6q_sabresd_pads));
	else if (cpu_is_mx6dl()) {
		mxc_iomux_v3_setup_multiple_pads(mx6dl_sabresd_pads,
			ARRAY_SIZE(mx6dl_sabresd_pads));
		num_cpu_idle_lock = 0xffff0000;
	}

#ifdef CONFIG_FEC_1588
	/* Set GPIO_16 input for IEEE-1588 ts_clk and RMII reference clock
	 * For MX6 GPR1 bit21 meaning:
	 * Bit21:       0 - GPIO_16 pad output
	 *              1 - GPIO_16 pad input
	 */
	 mxc_iomux_set_gpr_register(1, 21, 1, 1);
#endif

#ifdef CONFIG_FEC_1588
	/* Set GPIO_16 input for IEEE-1588 ts_clk and RMII reference clock
	 * For MX6 GPR1 bit21 meaning:
	 * Bit21:       0 - GPIO_16 pad output
	 *              1 - GPIO_16 pad input
	 */
	 mxc_iomux_set_gpr_register(1, 21, 1, 1);
#endif

	gp_reg_id = sabresd_dvfscore_data.reg_id;
	mx6q_sabresd_init_uart();

	/*
	 * MX6DL/Solo only supports single IPU
	 * The following codes are used to change ipu id
	 * and display id information for MX6DL/Solo. Then
	 * register 1 IPU device and up to 2 displays for
	 * MX6DL/Solo
	 */
	if (cpu_is_mx6dl()) {
		ldb_data.ipu_id = 0;
		ldb_data.disp_id = 1;
		hdmi_core_data.disp_id = 0;
		mipi_dsi_pdata.ipu_id = 0;
		mipi_dsi_pdata.disp_id = 1;
	}
	imx6q_add_mxc_hdmi_core(&hdmi_core_data);

	imx6q_add_ipuv3(0, &ipu_data[0]);
	if (cpu_is_mx6q())
		imx6q_add_ipuv3(1, &ipu_data[1]);
	for (i = 0; i < ARRAY_SIZE(sabresd_fb_data); i++)
		imx6q_add_ipuv3fb(i, &sabresd_fb_data[i]);

	imx6q_add_vdoa();
	imx6q_add_mipi_dsi(&mipi_dsi_pdata);
	imx6q_add_lcdif(&lcdif_data);
	if (!disable_ldb)
		imx6q_add_ldb(&ldb_data);
	imx6q_add_v4l2_output(0);
	imx6q_add_v4l2_capture(0);
	imx6q_add_mipi_csi2(&mipi_csi2_pdata);
	imx6q_add_imx_snvs_rtc();

	if (board_is_mx6_reva()) {
		strcpy(mxc_i2c0_board_info[0].type, "wm8958");
		mxc_i2c0_board_info[0].platform_data = &wm8958_config_data;
	} else {
		strcpy(mxc_i2c0_board_info[0].type, "wm8962");
		mxc_i2c0_board_info[0].platform_data = &wm8962_config_data;
	}
	imx6q_add_device_gpio_leds();

	imx6q_add_imx_i2c(0, &mx6q_sabresd_i2c_data);
	imx6q_add_imx_i2c(1, &mx6q_sabresd_i2c_data);
	imx6q_add_imx_i2c(2, &mx6q_sabresd_i2c_data);
	i2c_register_board_info(0, mxc_i2c0_board_info,
			ARRAY_SIZE(mxc_i2c0_board_info));
	i2c_register_board_info(1, mxc_i2c1_board_info,
			ARRAY_SIZE(mxc_i2c1_board_info));
	i2c_register_board_info(2, mxc_i2c2_board_info,
			ARRAY_SIZE(mxc_i2c2_board_info));
	ret = gpio_request(SABRESD_PFUZE_INT, "pFUZE-int");
	if (ret) {
		printk(KERN_ERR"request pFUZE-int error!!\n");
		return;
	} else {
		gpio_direction_input(SABRESD_PFUZE_INT);
		mx6q_sabresd_init_pfuze100(SABRESD_PFUZE_INT);
	}

	/* SPI */
	imx6q_add_ecspi(0, &mx6q_sabresd_spi_data);
	spi_device_init();

	imx6q_add_mxc_hdmi(&hdmi_data);

	imx6q_add_anatop_thermal_imx(1, &mx6q_sabresd_anatop_thermal_data);
	imx6_init_fec(fec_data);
	imx6q_add_pm_imx(0, &mx6q_sabresd_pm_data);
	/* Move sd4 to first because sd4 connect to emmc.
	   Mfgtools want emmc is mmcblk0 and other sd card is mmcblk1.
	*/
	imx6q_add_sdhci_usdhc_imx(3, &mx6q_sabresd_sd4_data);
	imx6q_add_sdhci_usdhc_imx(2, &mx6q_sabresd_sd3_data);
	imx6q_add_sdhci_usdhc_imx(1, &mx6q_sabresd_sd2_data);
	imx_add_viv_gpu(&imx6_gpu_data, &imx6q_gpu_pdata);
	imx6q_sabresd_init_usb();
	/* SATA is not supported by MX6DL/Solo */
	if (cpu_is_mx6q())
		imx6q_add_ahci(0, &mx6q_sabresd_sata_data);
	imx6q_add_vpu();
	imx6q_init_audio();
	platform_device_register(&sabresd_vmmc_reg_devices);
	imx_asrc_data.asrc_core_clk = clk_get(NULL, "asrc_clk");
	imx_asrc_data.asrc_audio_clk = clk_get(NULL, "asrc_serial_clk");
	imx6q_add_asrc(&imx_asrc_data);

	imx6q_add_mxc_pwm(0);
	imx6q_add_mxc_pwm(1);
	imx6q_add_mxc_pwm(2);
	imx6q_add_mxc_pwm(3);
	imx6q_add_mxc_pwm_backlight(0, &mx6_sabresd_pwm_backlight_data);

	imx6q_add_otp();
	imx6q_add_viim();
	imx6q_add_imx2_wdt(0, NULL);
	imx6q_add_dma();

	imx6q_add_dvfs_core(&sabresd_dvfscore_data);
	mx6_cpu_regulator_init();

	imx6q_add_ion(0, &imx_ion_data,
		sizeof(imx_ion_data) + sizeof(struct ion_platform_heap));
	imx6q_add_device_buttons();

	/* enable sensor 3v3 and 1v8 */
	gpio_request(SABRESD_SENSOR_EN, "sensor-en");
	gpio_direction_output(SABRESD_SENSOR_EN, 1);

	/* enable ecompass intr */
	gpio_request(SABRESD_eCOMPASS_INT, "ecompass-int");
	gpio_direction_input(SABRESD_eCOMPASS_INT);
	/* enable light sensor intr */
	gpio_request(SABRESD_ALS_INT, "als-int");
	gpio_direction_input(SABRESD_ALS_INT);

	imx6q_add_hdmi_soc();
	imx6q_add_hdmi_soc_dai();

	if (cpu_is_mx6dl()) {
		imx6dl_add_imx_pxp();
		imx6dl_add_imx_pxp_client();
		if (epdc_enabled) {
			mxc_register_device(&max17135_sensor_device, NULL);
			imx6dl_add_imx_epdc(&epdc_data);
		}
	}
	/*
	ret = gpio_request_array(mx6q_sabresd_flexcan_gpios,
			ARRAY_SIZE(mx6q_sabresd_flexcan_gpios));
	if (ret)
		pr_err("failed to request flexcan1-gpios: %d\n", ret);
	else
		imx6q_add_flexcan0(&mx6q_sabresd_flexcan0_pdata);
	*/

	clko2 = clk_get(NULL, "clko2_clk");
	if (IS_ERR(clko2))
		pr_err("can't get CLKO2 clock.\n");

	new_parent = clk_get(NULL, "osc_clk");
	if (!IS_ERR(new_parent)) {
		clk_set_parent(clko2, new_parent);
		clk_put(new_parent);
	}
	rate = clk_round_rate(clko2, 24000000);
	clk_set_rate(clko2, rate);
	clk_enable(clko2);

	/* Enable Aux_5V */
	gpio_request(SABRESD_AUX_5V_EN, "aux_5v_en");
	gpio_direction_output(SABRESD_AUX_5V_EN, 1);
	gpio_set_value(SABRESD_AUX_5V_EN, 1);

	pcie_3v3_power(false);
	msleep(10);
	pcie_3v3_power(true);
	msleep(10);
	pcie_3v3_reset();

	gps_power_on(true);

	/* Register charger chips */
	platform_device_register(&sabresd_max8903_charger_1);
	pm_power_off = mx6_snvs_poweroff;
	imx6q_add_busfreq();

	imx6q_add_pcie(&mx6_sabresd_pcie_data);
}

可以看出，初始化的是mx6dl_sabresd_pads这个函数，下面的是各种驱动的初始化。