HCIP第三次实验

1配ip写缺省

[r1]ip route-static 0.0.0.0 0 13.1.1.2

[r1]ip route-static 0.0.0.0 0 63.1.1.2

[r2]ip route-static 0.0.0.0 0 53.1.1.2

[r4]ip route-static 0.0.0.0 0 33.1.1.1

测试：

2能访问ar6环回

[r1]acl 2000

[r1-acl-basic-2000]rule permit source 192.168.1.0 0.0.0.255

[r1-acl-basic-2000]q

[r1]int g0/0/1

[r1-GigabitEthernet0/0/1]nat outbound 2000

[r1-GigabitEthernet0/0/0]nat outbound 2000

3 r1 r4 r5为全连的mgre结构

先建立全连网状mgre

[r1]int t0/0/1

[r1-Tunnel0/0/1]ip add 14.1.1.1 24

[r1-Tunnel0/0/1]tunnel-protocol gre p2mp

[r1-Tunnel0/0/1]source 13.1.1.1

Jan 3 2023 13:12:29-08:00 r1 %%01IFNET/4/LINK_STATE(l)[23]:The line protocol IP

on the interface Tunnel0/0/1 has entered the UP state.

[r1-Tunnel0/0/1]nhrp entry multicast dynamic

[r4]int t0/0/1

[r4-Tunnel0/0/1]ip add 14.1.1.2 2

Error: The specified IP address is invalid.

[r4-Tunnel0/0/1]ip add 14.1.1.2 24

[r4-Tunnel0/0/1]tunnel-protocol gre p2mp

[r4-Tunnel0/0/1]source 33.1.1.2

[r4-Tunnel0/0/1]nhrp entry 14.1.1.1 13.1.1.1 register

[r4-Tunnel0/0/1]nhrp entry 14.1.1.3 23.1.1.2 register

[r5]int t0/0/1

[r5-Tunnel0/0/1]ip add 14.1.1.3 24

[r5-Tunnel0/0/1]tunnel-protocol gre p2mp

[r5-Tunnel0/0/1]source 23.1.1.2

Jan 3 2023 13:17:40-08:00 r5 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP

on the interface Tunnel0/0/1 has entered the UP state.

[r5-Tunnel0/0/1]nhrp entry 14.1.1.1 13.1.1.1 register

[r5-Tunnel0/0/1]nhrp entry multicast dynamic

测试：

再把接口改为broadcast

[r1-GigabitEthernet0/0/1]ospf network-type broadcast

再写ospf

[r1]ospf 1

[r1-ospf-1]area 0

[r1-ospf-1-area-0.0.0.0]netw

[r1-ospf-1-area-0.0.0.0]network 14.1.1.0 0.0.0.255

[r1-ospf-1-area-0.0.0.0]netw

[r1-ospf-1-area-0.0.0.0]network 192.168.1.0 0.0.0.255

测试：

4 r1 r2 r3为星型结构

[r2]int Tunnel 0/0/0

[r2-Tunnel0/0/0]ip add 15.1.1.2 24

[r2-Tunnel0/0/0]tunnel-protocol gre p2mp

[r2-Tunnel0/0/0]source 53.1.1.1

Jan 3 2023 12:37:25-08:00 r2 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP

on the interface Tunnel0/0/0 has entered the UP state.

[r2-Tunnel0/0/0]nhrp entry 15.1.1.1 63.1.1.1 register

[r2-Tunnel0/0/0]nhrp network-id 100

先把mgre建立起来

再把接口改为broadcast

[r1-Tunnel0/0/0]ospf network-type broadcast

[r3-Tunnel0/0/0]ospf network-type broadcast

再写ospf

[r1]ospf 1

[r1-ospf-1]area 0

[r1-ospf-1-area-0.0.0.0]network 192.168.1.0 0.0.0.255

[r1-ospf-1-area-0.0.0.0]network 15.1.1.0 0.0.0.255

[r2]ospf 1

[r2-ospf-1]area 0

[r2-ospf-1-area-0.0.0.0]network 15.1.1.0 0.0.0.255

[r2-ospf-1-area-0.0.0.0]netw

[r2-ospf-1-area-0.0.0.0]network 192.168.2.0 0.0.0.255

三个都写完以后测试：

4 全网通测试