外部中断(库函数)

/*
    头文件
*/


#ifndef EXTI_H
#define EXTI_H
#include "stm32f10x.h"
#include "led.h"
void exti_init(void);

#endif

/*
1.配置模式:
    a.GPIO模式
    b.EXTI模式
    c.NVIC模式
2.使能时钟
    a.对应GPIO时钟
    b.AFIO时钟,作为管脚复用,一定要开启这个时钟
    c.打开对应的中断线

3.这里不像串口要使能串口,不过打开对应的中断线与之类似,也不用开中断.



*/

#include "exti.h"

void exti_init(void)
{
	EXTI_InitTypeDef EXTI_InitStructure;
 	NVIC_InitTypeDef NVIC_InitStructure;
 	GPIO_InitTypeDef GPIO_InitStructure;
	//开启GPIO时钟
 	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_GPIOE,ENABLE);
	//开启AFIO时钟
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO,ENABLE);
	
	//打开对应的中断线
	GPIO_EXTILineConfig(GPIO_PortSourceGPIOE,GPIO_PinSource3);
	GPIO_EXTILineConfig(GPIO_PortSourceGPIOE,GPIO_PinSource4);
	GPIO_EXTILineConfig(GPIO_PortSourceGPIOA,GPIO_PinSource0);

	
	//配置GPIO模式
	GPIO_InitStructure.GPIO_Pin  = GPIO_Pin_4|GPIO_Pin_3;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU; 
 	GPIO_Init(GPIOE, &GPIO_InitStructure);

	
	GPIO_InitStructure.GPIO_Pin  = GPIO_Pin_0;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPD;   
	GPIO_Init(GPIOA, &GPIO_InitStructure);
    
	
	
	  
	//配置外部中断模式
  	EXTI_InitStructure.EXTI_Line=EXTI_Line3;
  	EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;	
  	EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;
  	EXTI_Init(&EXTI_InitStructure);	  	

 	
  	EXTI_InitStructure.EXTI_Line=EXTI_Line4;
  	EXTI_Init(&EXTI_InitStructure);	  	

   
  	EXTI_InitStructure.EXTI_Line=EXTI_Line0;
  	EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
  	EXTI_Init(&EXTI_InitStructure);		




	//配置中断模式
  	NVIC_InitStructure.NVIC_IRQChannel = EXTI0_IRQn;			
  	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x02;	
  	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x03;				
  	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;						
  	NVIC_Init(&NVIC_InitStructure); 

  	NVIC_InitStructure.NVIC_IRQChannel = EXTI3_IRQn;			
  	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x02;	
  	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x01;					
  	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;							
  	NVIC_Init(&NVIC_InitStructure);  	  

  	NVIC_InitStructure.NVIC_IRQChannel = EXTI4_IRQn;			
  	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x02;	
  	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x00;					
  	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;							
  	NVIC_Init(&NVIC_InitStructure);  	  

  
}


/*
中断服务函数:
    1.有人进入中断还像按键输入那样消抖,我认为没必要,有抖动的话又会产生中断
    2.一定要清除中断标志位,这个有一个方法不用清就是我们改变触发方式,我们通常不这么做

*/



void EXTI0_IRQHandler(void)
{
	LED1(OFF);
	LED0(OFF);
	EXTI_ClearITPendingBit(EXTI_Line0); //清除LINE0上的中断标志位  
}

void EXTI3_IRQHandler(void)
{

	LED1(ON);
EXTI_ClearITPendingBit(EXTI_Line3);  //清除LINE3上的中断标志位 
}

void EXTI4_IRQHandler(void)
{

	LED0(ON);
EXTI_ClearITPendingBit(EXTI_Line4);  //清除LINE4上的中断标志位  
}

/*主函数*/

#include "stm32f10x.h"
#include "led.h"
#include "beep.h"
#include "key.h"
#include "usart.h"
#include "exti.h"


void delay(u32 i){while(i--);}
u8 i=0;

int main(void)
{
	NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
	led_init();
	beep_init();
	exti_init();

	while(1)
	{
		

	}


}