蓝桥杯嵌入式扩展板模块之两路采集

关于这个模块其实我在前面的博客中已经写的比较详细了，因此我在这只是放一下代码而已。
传送门：STM32ADC模块-温度传感器的单通道采集与多通道采集
关于DMA参数中文详解参考：STM32DMA使用详解

硬件背景

双通道的实现

adc.c

#include "adc_DMA.h"

uint16_t Adc_Number[30][3];
uint16_t After_filter[3];

void Adc_DMA_Init(void){
	ADC_InitTypeDef ADC_InitStructure;
	DMA_InitTypeDef DMA_InitStructure;	
	GPIO_InitTypeDef GPIO_InitStructure;
	NVIC_InitTypeDef NVIC_InitStructure;
	
	RCC_ADCCLKConfig(RCC_PCLK2_Div6); 
	RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1 | RCC_APB2Periph_GPIOA| RCC_APB2Periph_GPIOB, ENABLE);	

	NVIC_InitStructure.NVIC_IRQChannel = DMA1_Channel1_IRQn; 
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1; 
    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0; 
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; 
    NVIC_Init(&NVIC_InitStructure);         				 
	
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_4 | GPIO_Pin_5;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
	GPIO_Init(GPIOA, &GPIO_InitStructure);	
	
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN;
	GPIO_Init(GPIOB, &GPIO_InitStructure);	

	/* DMA1 channel1 configuration ----------------------------------------------*/
	DMA_DeInit(DMA1_Channel1);
	DMA_InitStructure.DMA_PeripheralBaseAddr = ADC1_DR_Address;
	DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)&Adc_Number;
	DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
	DMA_InitStructure.DMA_BufferSize = 90;
	DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
	DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
	DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord;
	DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_HalfWord;
	DMA_InitStructure.DMA_Mode = DMA_Mode_Circular;
	DMA_InitStructure.DMA_Priority = DMA_Priority_High;
	DMA_InitStructure.DMA_M2M = DMA_M2M_Disable;
	DMA_Init(DMA1_Channel1, &DMA_InitStructure);  
	/* Enable DMA1 channel1 */
	DMA_Cmd(DMA1_Channel1, ENABLE);	
	DMA_ITConfig(DMA1_Channel1,DMA_IT_TC, ENABLE); 	//使能DMA传输完成中断 
	
	
	/* ADC1 configuration ------------------------------------------------------*/
	ADC_InitStructure.ADC_Mode = ADC_Mode_Independent;
	ADC_InitStructure.ADC_ScanConvMode = ENABLE ;
	ADC_InitStructure.ADC_ContinuousConvMode = ENABLE;
	ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None;
	ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
	ADC_InitStructure.ADC_NbrOfChannel = 3;
	ADC_Init(ADC1, &ADC_InitStructure);
	/* ADC1 regular channels configuration */ 
	ADC_RegularChannelConfig(ADC1, ADC_Channel_4, 1, ADC_SampleTime_239Cycles5);
	ADC_RegularChannelConfig(ADC1, ADC_Channel_5, 2, ADC_SampleTime_239Cycles5);
	ADC_RegularChannelConfig(ADC1, ADC_Channel_8, 3, ADC_SampleTime_239Cycles5);     
	/* Enable ADC1 DMA */
	ADC_DMACmd(ADC1, ENABLE);	
	/* Enable ADC1 */
	ADC_Cmd(ADC1, ENABLE);
	/* Enable ADC1 reset calibration register */   
	ADC_ResetCalibration(ADC1);
	/* Check the end of ADC1 reset calibration register */
	while(ADC_GetResetCalibrationStatus(ADC1));
	/* Start ADC1 calibration */
	ADC_StartCalibration(ADC1);
	/* Check the end of ADC1 calibration */
	while(ADC_GetCalibrationStatus(ADC1));
	  /* Start ADC1 Software Conversion */ 
	ADC_SoftwareStartConvCmd(ADC1, ENABLE);
	
}

void DMA1_Channel1_IRQHandler(void)
{
	if(DMA_GetITStatus(DMA1_IT_TC1) != RESET)
	{
		int sum = 0;
		u8 i,j;
		for(i=0;i<3;i++)
		{
			for (j=0;j<30;j++)
			{
				sum += Adc_Number[j][i];
			}
			After_filter[i]=sum/30;
			sum=0;
		}
		DMA_ClearITPendingBit(DMA1_IT_TC1);
	}
}

float GetVolt(u16 advalue)   
{
   
    return advalue*3.3/4095;   
} 

adc.h

#ifndef __ADC_DMA_H
#define __ADC_DMA_H

#include "main.h"	

extern uint16_t After_filter[3];

#define ADC1_DR_Address    ((uint32_t)0x4001244C)

void Adc_DMA_Init(void);
void DMA1_Channel1_IRQHandler(void);
float GetVolt(u16 advalue);

#endif