stm32f030定时器中断LED闪烁程序代码

程序代码

#include "stm32f0xx.h"

//初始化LED,GPIO.GPIOA第四pin是连接的LED,
void GPIO_Config(void)
{
    GPIO_InitTypeDef GPIO_InitStructure;
    RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA,ENABLE);

    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_4;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_10MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
	GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
    GPIO_Init(GPIOA,&GPIO_InitStructure);
    GPIO_SetBits(GPIOA,GPIO_Pin_4); //关闭LED
}

//初始化定时器和中断
void TIM3_Int_Init(uint16_t arr,uint16_t psc)
{
    TIM_TimeBaseInitTypeDef  TIM_TimeBaseStructure;
	NVIC_InitTypeDef NVIC_InitStructure;
 
	RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE); //时钟使能
	
	//定时器TIM3初始化
	TIM_TimeBaseStructure.TIM_Period = arr; //设置在下一个更新事件装入活动的自动重装载寄存器周期的值	
	TIM_TimeBaseStructure.TIM_Prescaler =psc; //设置用来作为TIMx时钟频率除数的预分频值
	TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1; //设置时钟分割:TDTS = Tck_tim
	TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;  //TIM向上计数模式
	TIM_TimeBaseInit(TIM3, &TIM_TimeBaseStructure); //根据指定的参数初始化TIMx的时间基数单位
 
	TIM_ITConfig(TIM3,TIM_IT_Update,ENABLE ); //使能指定的TIM3中断,允许更新中断
 
	//中断优先级NVIC设置
	NVIC_InitStructure.NVIC_IRQChannel = TIM3_IRQn;  //TIM3中断
	NVIC_InitStructure.NVIC_IRQChannelPriority = 0;  //先占优先级0级
	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; //IRQ通道被使能
	NVIC_Init(&NVIC_InitStructure);  //初始化NVIC寄存器
 
	TIM_Cmd(TIM3, ENABLE);  //使能TIMx					 
}

//主函数
int main(void)
{
    GPIO_Config();
    //((1+arr )/72M)*(1+psc )=((1+1999)/72M)*(1+35999)=1秒
    TIM3_Int_Init(4999,7199);
    while(1);

}



//--------------------stm32f0xx_.c------------------------
//中断函数中需要完成的事情自己去编写
//本例是定时器1秒中断发生后，对LED进行取反操作。
void TIM3_IRQHandler(void)
{
    //判断TIM3更新中断是否发生
    if(TIM_GetITStatus(TIM3,TIM_IT_Update)!=RESET)
    {
    //必须清楚标志位
    TIM_ClearITPendingBit(TIM3,TIM_IT_Update);
    //状态取反
    GPIO_WriteBit(GPIOA,GPIO_Pin_4,(BitAction)(!GPIO_ReadOutputDataBit(GPIOA,GPIO_Pin_4)));
    }

}