STM32F103C8T6基本功能代码

点亮一个LED灯（A 13）

LED.c

#include "led.h"

void LED_Init(void)
{
    GPIO_InitTypeDef GPIO_InitStructure;

    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA);//使能PA端口时钟
    GPIO_InitStructure.GPIO_Mode=GPIO_Mode_Out_PP;//推挽输出
    GPIO_InitStructure.GPIO_Speed=GPIO_Speed_50MHz;

    GPIO_InitStructure.GPIO_Pin=GPIO_Pin_13;//LED1-->PE1推挽输出
    GPIO_Init(GPIOA,&GPIO_InitStructure);
    GPIO_ResetBits(GPIOA,GPIO_Pin_13);//PE1 输出低

}

LED.h

#ifndef __LED__H
#define __LED__H

#include "stm32f10x.h"

#define LED_OFF     GPIO_SetBits(GPIOA, GPIO_Pin_13)
#define LED_ON         GPIO_ResetBits(GPIOA, GPIO_Pin_13)


void LED_Init(void);

#endif 

串口使用（A 9,A 10），串口的中断函数

多个串口使用时，更改引脚即可。

Usart.c

void USART1_Init(u32 bound)
{
	GPIO_InitTypeDef 	GPIO_InitStructure;
	USART_InitTypeDef 	USART_InitStructure;
	NVIC_InitTypeDef 	NVIC_InitStructure;
	/* config USART1 clock */
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1 | RCC_APB2Periph_GPIOA, ENABLE);
	NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);	
	
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;//USART1 Tx (PA.09)
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_Init(GPIOA, &GPIO_InitStructure);    

	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;//USART1 Rx (PA.10)
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
	GPIO_Init(GPIOA, &GPIO_InitStructure);
	/* USART1 mode config */
	USART_InitStructure.USART_BaudRate = bound;
	USART_InitStructure.USART_WordLength = USART_WordLength_8b;
	USART_InitStructure.USART_StopBits = USART_StopBits_1;
	USART_InitStructure.USART_Parity = USART_Parity_No ;
	USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
	USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
	USART_Init(USART1, &USART_InitStructure); 
	USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);
	USART_Cmd(USART1, ENABLE);
	
	NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn;	
	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
	NVIC_Init(&NVIC_InitStructure);
}

void USART1_IRQHandler(void)                
{	
	u32 i;
	
	if(USART_GetITStatus(USART1, USART_IT_RXNE) != RESET)  
	{
		i=USART_ReceiveData(USART1);
		USART_SendData(USART1,i);			
//		while(USART_GetFlagStatus(USART1,USART_FLAG_TC) != SET);

	} 
//	USART_ClearFlag(USART1,USART_FLAG_TC);

} 	

Usart.h

#ifndef _usart_H
#define _usart_H

#include "stm32f10x.h"

void USART1_Init(u32 bound);
void USART2_Init(u32 bound);

void USART1_IRQHandler(void);
void USART2_IRQHandler(void);

#endif

sys.h

#ifndef __SYS_H
#define __SYS_H	
#include "stm32f10x.h"

//0,不支持ucos
//1,支持ucos
#define SYSTEM_SUPPORT_OS		0		//定义系统文件夹是否支持UCOS
																	    
	 
//位带操作,实现51类似的GPIO控制功能
//具体实现思想,参考<<CM3权威指南>>第五章(87页~92页).
//IO口操作宏定义
#define BITBAND(addr, bitnum) ((addr & 0xF0000000)+0x2000000+((addr &0xFFFFF)<<5)+(bitnum<<2)) 
#define MEM_ADDR(addr)  *((volatile unsigned long  *)(addr)) 
#define BIT_ADDR(addr, bitnum)   MEM_ADDR(BITBAND(addr, bitnum)) 
//IO口地址映射
#define GPIOA_ODR_Addr    (GPIOA_BASE+12) //0x4001080C 
#define GPIOB_ODR_Addr    (GPIOB_BASE+12) //0x40010C0C 
#define GPIOC_ODR_Addr    (GPIOC_BASE+12) //0x4001100C 
#define GPIOD_ODR_Addr    (GPIOD_BASE+12) //0x4001140C 
#define GPIOE_ODR_Addr    (GPIOE_BASE+12) //0x4001180C 
#define GPIOF_ODR_Addr    (GPIOF_BASE+12) //0x40011A0C    
#define GPIOG_ODR_Addr    (GPIOG_BASE+12) //0x40011E0C    

#define GPIOA_IDR_Addr    (GPIOA_BASE+8) //0x40010808 
#define GPIOB_IDR_Addr    (GPIOB_BASE+8) //0x40010C08 
#define GPIOC_IDR_Addr    (GPIOC_BASE+8) //0x40011008 
#define GPIOD_IDR_Addr    (GPIOD_BASE+8) //0x40011408 
#define GPIOE_IDR_Addr    (GPIOE_BASE+8) //0x40011808 
#define GPIOF_IDR_Addr    (GPIOF_BASE+8) //0x40011A08 
#define GPIOG_IDR_Addr    (GPIOG_BASE+8) //0x40011E08 
 
//IO口操作,只对单一的IO口!
//确保n的值小于16!
#define PAout(n)   BIT_ADDR(GPIOA_ODR_Addr,n)  //输出 
#define PAin(n)    BIT_ADDR(GPIOA_IDR_Addr,n)  //输入 

#define PBout(n)   BIT_ADDR(GPIOB_ODR_Addr,n)  //输出 
#define PBin(n)    BIT_ADDR(GPIOB_IDR_Addr,n)  //输入 

#define PCout(n)   BIT_ADDR(GPIOC_ODR_Addr,n)  //输出 
#define PCin(n)    BIT_ADDR(GPIOC_IDR_Addr,n)  //输入 

#define PDout(n)   BIT_ADDR(GPIOD_ODR_Addr,n)  //输出 
#define PDin(n)    BIT_ADDR(GPIOD_IDR_Addr,n)  //输入 

#define PEout(n)   BIT_ADDR(GPIOE_ODR_Addr,n)  //输出 
#define PEin(n)    BIT_ADDR(GPIOE_IDR_Addr,n)  //输入

#define PFout(n)   BIT_ADDR(GPIOF_ODR_Addr,n)  //输出 
#define PFin(n)    BIT_ADDR(GPIOF_IDR_Addr,n)  //输入

#define PGout(n)   BIT_ADDR(GPIOG_ODR_Addr,n)  //输出 
#define PGin(n)    BIT_ADDR(GPIOG_IDR_Addr,n)  //输入

//以下为汇编函数
void WFI_SET(void);		//执行WFI指令
void INTX_DISABLE(void);//关闭所有中断
void INTX_ENABLE(void);	//开启所有中断
void MSR_MSP(u32 addr);	//设置堆栈地址

#endif

STM32滴答定时器（Systick）

SysTick.c

#include "SysTick.h"

static u8  fac_us=0;
static u16 fac_ms=0;

void SysTick_Init (u8 SYSCLK)
{
	SysTick_CLKSourceConfig(SysTick_CLKSource_HCLK_Div8); 
    fac_us = SystemCoreClock/8000000;  					
	fac_ms=(u16)fac_us*1000;				   
}

void delay_us (u32 nus)
{		
	u32 temp;	    	 
	SysTick->LOAD=nus*fac_us; 							 
	SysTick->VAL=0x00;        			
	SysTick->CTRL|=SysTick_CTRL_ENABLE_Msk ; 
	do
	{
		temp=SysTick->CTRL;
	}
	while((temp&0x01)&&!(temp&(1<<16)));		
	SysTick->CTRL&=~SysTick_CTRL_ENABLE_Msk;
	SysTick->VAL =0X00;  
}

void delay_ms (u16 nms)
{	 		  	  
	u32 temp;		   
	SysTick->LOAD=(u32)nms*fac_ms;	
	SysTick->VAL =0x00;	
	SysTick->CTRL|=SysTick_CTRL_ENABLE_Msk ;
	do
	{
		temp=SysTick->CTRL;
	}
	while((temp&0x01)&&!(temp&(1<<16)));
	SysTick->CTRL&=~SysTick_CTRL_ENABLE_Msk;
	SysTick->VAL =0X00;   	    
}

SysTick.h

#ifndef _SysTick_H
#define _SysTick_H


#include "stm32f10x.h"


#define u8   unsigned char
#define u16  unsigned short 
#define u32  unsigned int
	
	
void SysTick_Init (u8 SYSCLK);
void delay_us (u32 nus);
void delay_ms (u16 nms);


#endif