CELT编码解码 - 实例

直接上源码，希望可以帮到各位

#ifdef HAVE_CONFIG_H
#include "config.h"
#endif

#include "celt.h"
#include "arch.h"
#include <stdio.h>

#ifndef _MSC_VER
#include <unistd.h>
#endif

//当前libcelt的版本是 0.11.1

/**
* @brief 注意：libcet中需要加一下 CUSTOM_MODES 的预定义，不然celt_mode_create只支持mode48000_960_120的编解码
* 另外如果存在对 HAVE_CONFIG_H 的预定义的话，可以先屏蔽掉
*/

//{960,512,480,256,240,128,120,64} 一般用这些值，值越大时编解码越快但导致最后会丢弃的原始数据长度可能越长
#define FRAME_SIZE 960 //表示一次处理960个字节的数据
const unsigned int g_channel = 2; //当前pcm的声道数

void CeltCodec(celt_int16* sAudio, int nLen)/* sAudio需要编码的数据 */
{
	//初始化
	int err = 0;
	int samplingrate = 44100;
	int channl = g_channel;
	int nEncodingAudioLength = 0;//编码后的音频数据长度
	unsigned char cEncodingAudioContainer[FRAME_SIZE];//编码后的音频数据

	//初始化CELT模型
	CELTMode * mode = celt_mode_create(samplingrate, FRAME_SIZE, &err);
	CELTEncoder * enc_state = celt_encoder_create_custom(mode, channl, &err);
	CELTDecoder * dec_state = celt_decoder_create_custom(mode, channl, &err);

	FILE* fp_en;
	fopen_s(&fp_en, "E:\\input_en.data", "wb+");
	for (int i = 0; i < nLen; i = i + (FRAME_SIZE * channl))
	{
		if ( (i + FRAME_SIZE * channl) >= (nLen - FRAME_SIZE * channl) )
			break;
		//开始编码
		nEncodingAudioLength = celt_encode(enc_state, (celt_int16*)(sAudio + i), FRAME_SIZE, cEncodingAudioContainer, FRAME_SIZE);
		//把编码后的中间数据保存起来
		fwrite(cEncodingAudioContainer, nEncodingAudioLength, sizeof(unsigned char), fp_en);
	}
	fclose(fp_en);

	/**
	* 假设此处有传输，即input_en.data数据需要传给其他端进行解码
	*/

	//读取编码后的中间数据
	FILE* fp_read;
	fopen_s(&fp_read, "E:\\input_en.data", "rb");
	fseek(fp_read, 0, SEEK_END);
	long nFileLen = ftell(fp_read);
	fseek(fp_read, 0, SEEK_SET);
	char* pBuff_read = (char*)malloc(nFileLen + 1);
	memset(pBuff_read, 0, nFileLen + 1);
	fread(pBuff_read, nFileLen, 1, fp_read);
	fclose(fp_read);

	FILE* fp;
	fopen_s(&fp, "E:\\output.pcm", "wb+");
	//celt解码
	for (int i = 0; i < nFileLen; i = i + nEncodingAudioLength)
	{
		if (i + nEncodingAudioLength >= nFileLen)
			break;
		//分配内存
		int nDecSize = FRAME_SIZE * channl * sizeof(celt_int16);
		celt_int16 * out = (celt_int16*)malloc(nDecSize);
		memset(out, 0, nDecSize);
		//开始解码
		int ret = celt_decode(dec_state, pBuff_read + i, nEncodingAudioLength, out, FRAME_SIZE);
		//类型转换
		fwrite(out, FRAME_SIZE * channl, sizeof(celt_int16), fp);
	}
	fclose(fp);

	//播放声音
	//这里我用的ffmpeg命令进行验证
	//具体命令：ffplay.exe -ar 44100 -ac 2 -f s16le -i "E:\\output.pcm"
}

int main()
{
	FILE* fp;
	fopen_s(&fp, "E:\\input.pcm", "rb");
	fseek(fp, 0, SEEK_END);
	long nFileLen = ftell(fp);
	fseek(fp, 0, SEEK_SET);
	char* pBuff = (char*)malloc(nFileLen + 1);
	memset(pBuff, 0, nFileLen + 1);
	fread(pBuff, nFileLen, 1, fp);
	fclose(fp);

	if(g_channel == 2) // 此处需要知道声道数是多少(目前只处理双声道)
		CeltCodec((celt_int16*)pBuff, nFileLen >> 1);

	free(pBuff);
	return 0;
}