esp32

最新推荐文章于 2024-09-22 23:06:59 发布

GKoSon

最新推荐文章于 2024-09-22 23:06:59 发布

阅读量617

点赞数

文章标签： stm32 spring boot

本文链接：https://blog.csdn.net/weixin_42381351/article/details/120655907

版权

idf.py set-target esp32
idf.py menuconfig

无需修改

idf.py build

+++++++++++++++++++

新板子岔开自动的LOG 一直在复位

ets Jun  8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:7180
ho 0 tail 12 room 4
load:0x40078000,len:13200
load:0x40080400,len:4564
entry 0x400806f4
[0;32mI (29) boot: ESP-IDF v4.2.1-64-gd9ec7df39 2nd stage bootloader[0m
[0;32mI (29) boot: compile time 13:51:21[0m
[0;32mI (29) boot: chip revision: 1[0m
[0;32mI (33) boot_comm: chip revision: 1, min. bootloader chip revision: 0[0m
[0;32mI (40) boot.esp32: SPI Speed      : 40MHz[0m
[0;32mI (44) boot.esp32: SPI Mode       : DIO[0m
[0;32mI (49) boot.esp32: SPI Flash Size : 4MB[0m
[0;32mI (53) boot: Enabling RNG early entropy source...[0m
[0;32mI (59) boot: Partition Table:[0m
[0;32mI (62) boot: ## Label            Usage          Type ST Offset   Length[0m
[0;32mI (70) boot:  0 phy_init         RF data          01 01 0000f000 00001000[0m
[0;32mI (77) boot:  1 otadata          OTA data         01 00 00010000 00002000[0m
[0;32mI (85) boot:  2 nvs              WiFi data        01 02 00012000 0000e000[0m
[0;32mI (92) boot:  3 at_customize     unknown          40 00 00020000 000e0000[0m
[0;32mI (100) boot:  4 ota_0            OTA app          00 10 00100000 00180000[0m
[0;32mI (107) boot:  5 ota_1            OTA app          00 11 00280000 00180000[0m
[0;32mI (115) boot: End of partition table[0m
[0;32mI (119) boot_comm: chip revision: 1, min. application chip revision: 0[0m
[0;32mI (126) esp_image: segment 0: paddr=0x00100020 vaddr=0x3f400020 size=0x1c3e0 (115680) map[0m
[0;32mI (179) esp_image: segment 1: paddr=0x0011c408 vaddr=0x3ffbdb60 size=0x0371c ( 14108) load[0m
[0;32mI (185) esp_image: segment 2: paddr=0x0011fb2c vaddr=0x40080000 size=0x004ec (  1260) load[0m
[0;32mI (187) esp_image: segment 3: paddr=0x00120020 vaddr=0x400d0020 size=0x1032c8 (1061576) map[0m
[0;32mI (599) esp_image: segment 4: paddr=0x002232f0 vaddr=0x400804ec size=0x1d090 (118928) load[0m
[0;32mI (652) esp_image: segment 5: paddr=0x00240388 vaddr=0x400c0000 size=0x00064 (   100) load[0m
[0;32mI (667) boot: Loaded app from partition at offset 0x100000[0m
[0;32mI (668) boot: Disabling RNG early entropy source...[0m

使用工具试试前面C3是不行这里直接OK 不需要按键就开始了

D:\迅雷下载\esp_hosted_firmware_esp32_sdio_uart_v0.3\esp_hosted_bootloader_esp32_sdio_uart_v0.3.bin
D:\迅雷下载\esp_hosted_firmware_esp32_sdio_uart_v0.3\esp_hosted_firmware_esp32_sdio_uart_v0.3.bin
D:\迅雷下载\esp_hosted_firmware_esp32_sdio_uart_v0.3\esp_hosted_partition-table_esp32_sdio_uart_v0.3.bin
参考 https://github.com/espressif/esp-hosted/blob/master/docs/Linux_based_host/UART_setup.md
$ python esptool.py --chip esp32 --port <serial_port> --baud 960000 --before default_reset \
--after hard_reset write_flash -z --flash_mode dio --flash_freq 40m --flash_size detect \
0x1000 esp_hosted_bootloader_esp32_<transport>_uart_v<release_version>.bin \
0x10000 esp_hosted_firmware_esp32_<transport>_uart_v<release_version>.bin \
0x8000 esp_hosted_partition-table_esp32_<transport>_uart_v<release_version>.bin