stm32定时器

第一个现象使oled上面显示数字计数：

.h:

#ifndef __TIMER_H
#define __TIMER_H
void Timer_Init(void);





#endif

.c:

#include "stm32f10x.h"                  // Device header

extern uint16_t Num;

void Timer_Init(void){
	//rCC
	RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2,ENABLE);
	//select internal timer
	TIM_InternalClockConfig(TIM2);
	//init time-based units
	TIM_TimeBaseInitTypeDef TIM_TimeBaseInitStructure;
	TIM_TimeBaseInitStructure.TIM_ClockDivision=TIM_CKD_DIV1;
	TIM_TimeBaseInitStructure.TIM_CounterMode=TIM_CounterMode_Up;
	//How many numbers count as a second 
	TIM_TimeBaseInitStructure.TIM_Period=10000-1;
	TIM_TimeBaseInitStructure.TIM_Prescaler=7200-1;
	TIM_TimeBaseInitStructure.TIM_RepetitionCounter=0;
	TIM_TimeBaseInit(TIM2,&TIM_TimeBaseInitStructure);
	
	TIM_ClearFlag(TIM2,TIM_FLAG_Update);
	
	
	//Enable interrupts
	TIM_ITConfig(TIM2,TIM_IT_Update,ENABLE);
	//nvic
	NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
	NVIC_InitTypeDef NVIC_InitStructure;
	NVIC_InitStructure.NVIC_IRQChannel = TIM2_IRQn;
	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 2;
	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
	NVIC_Init(&NVIC_InitStructure);
	//Start the timer
	TIM_Cmd(TIM2, ENABLE);	
}
//Interrupt function of timer 2
void TIM2_IRQHandler(void){
	//Check the break flag bit
	if(TIM_GetITStatus(TIM2,TIM_IT_Update)==SET){
		Num++;
		TIM_ClearITPendingBit(TIM2, TIM_IT_Update);
	}
}
	

第二个现象：外部定时器中断:

.h:

#ifndef __TIMER_H
#define __TIMER_H
void Timer_Init(void);
uint16_t Timer_GetCounter(void);





#endif

.c:

#include "stm32f10x.h"                  // Device header

extern uint16_t Num;

void Timer_Init(void){
	//rCC
	RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2,ENABLE);
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
	
	GPIO_InitTypeDef GPIO_InitStructure;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_Init(GPIOA, &GPIO_InitStructure);

	
	
	TIM_ETRClockMode2Config(TIM2,TIM_ExtTRGPSC_OFF,TIM_ExtTRGPolarity_NonInverted,0x00);
	
	//init time-based units
	TIM_TimeBaseInitTypeDef TIM_TimeBaseInitStructure;
	TIM_TimeBaseInitStructure.TIM_ClockDivision=TIM_CKD_DIV1;
	TIM_TimeBaseInitStructure.TIM_CounterMode=TIM_CounterMode_Up;
	//How many numbers count as a second 
	TIM_TimeBaseInitStructure.TIM_Period=10-1;
	TIM_TimeBaseInitStructure.TIM_Prescaler=1-1;
	TIM_TimeBaseInitStructure.TIM_RepetitionCounter=0;
	TIM_TimeBaseInit(TIM2,&TIM_TimeBaseInitStructure);
	
	TIM_ClearFlag(TIM2,TIM_FLAG_Update);
	
	
	//Enable interrupts
	TIM_ITConfig(TIM2,TIM_IT_Update,ENABLE);
	//nvic
	NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
	NVIC_InitTypeDef NVIC_InitStructure;
	NVIC_InitStructure.NVIC_IRQChannel = TIM2_IRQn;
	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 2;
	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
	NVIC_Init(&NVIC_InitStructure);
	//Start the timer
	TIM_Cmd(TIM2, ENABLE);	
}

uint16_t Timer_GetCounter(void)
{
	return TIM_GetCounter(TIM2);
}



//Interrupt function of timer 2
void TIM2_IRQHandler(void){
	//Check the break flag bit
	if(TIM_GetITStatus(TIM2,TIM_IT_Update)==SET){
		Num++;
		TIM_ClearITPendingBit(TIM2, TIM_IT_Update);
	}
}
		

以前还觉得能做出来点小玩意还沾沾自喜，现在觉得真是人外有人，天外有天，学的太少了，不够谦虚…