GD32f350输出PWM配置

void gpio_config_led(void)
{
    rcu_periph_clock_enable(RCU_GPIOB);    //使能GPIOB时钟
    /*Configure PB1 (TIM13-CH0 as alternate function*/
    gpio_mode_set(GPIOB, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO_PIN_1);
    gpio_output_options_set(GPIOB, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ,GPIO_PIN_1);
    gpio_af_set(GPIOB, GPIO_AF_0, GPIO_PIN_1);//这条语句需要特别注意，GPIO_AF_0需要注意
}

void led_config(unsigned short arr, unsigned short psc)//timer2-ch1
{
    timer_oc_parameter_struct timer_ocinitpara;
    timer_parameter_struct timer_initpara;

    rcu_periph_clock_enable(RCU_TIMER13);   //使能TIMER1时钟
    timer_channel_remap_config(TIMER13,TIMER13_CI0_RMP_GPIO);
    timer_deinit(TIMER13);                    //总清

    /* TIMER1 configuration */
    
     timer_initpara.prescaler         = psc;                //设置预分频值
     timer_initpara.alignedmode       = TIMER_COUNTER_EDGE; //设置对齐模式
     timer_initpara.counterdirection  = TIMER_COUNTER_UP;   //设置向上计数
     timer_initpara.period            = arr;                //设置重装载值
     timer_initpara.clockdivision     = TIMER_CKDIV_DIV1;   //设置时钟分频因子
    
//     timer_initpara.repetitioncounter = 0;                  //设置重复计数值
    
    timer_init(TIMER13, &timer_initpara);                   //初始化定时器
    
     
    
    timer_ocinitpara.outputstate  = TIMER_CCX_ENABLE;                    //设置通道输出状态
    timer_ocinitpara.outputnstate = TIMER_CCXN_DISABLE;                  //设置互补通道输出状态
    timer_ocinitpara.ocpolarity   = TIMER_OC_POLARITY_HIGH;              //设置通道输出极性
    timer_ocinitpara.ocnpolarity  = TIMER_OCN_POLARITY_HIGH;             //设置互补通道输出极性
    timer_ocinitpara.ocidlestate  = TIMER_OC_IDLE_STATE_LOW;             //设置空闲状态下通道输出极性
    timer_ocinitpara.ocnidlestate = TIMER_OCN_IDLE_STATE_LOW;            //设置空闲状态下互补通道输出极性

    timer_channel_output_config(TIMER13,TIMER_CH_0,&timer_ocinitpara);
    
    timer_channel_output_polarity_config(TIMER13,TIMER_CH_0,TIMER_OC_POLARITY_HIGH);

    timer_channel_output_pulse_value_config(TIMER13,TIMER_CH_0,0);                  //设置占空比
    timer_channel_output_mode_config(TIMER13,TIMER_CH_0,TIMER_OC_MODE_PWM0);        //设置通道比较模式
    timer_channel_output_shadow_config(TIMER13,TIMER_CH_0,TIMER_OC_SHADOW_DISABLE);    //失能比较影子寄存器
    timer_primary_output_config(TIMER13, ENABLE);

    timer_auto_reload_shadow_enable(TIMER13);                        //自动重载影子使能
    timer_automatic_output_enable(TIMER13);
    timer_enable(TIMER13);                                            //使能定时器
}