6.4.1.4.3 Handling of network rejection not due to congestion control

If the 5GSM cause value is different from #26 "insufficient resources", #28 "unknown PDU session type", #39 "reactivation requested", #46 "out of LADN service area", #50 "PDU session type IPv4 only allowed", #51 "PDU session type IPv6 only allowed", #54 "PDU session does not exist", #57 "PDU session type IPv4v6 only allowed", #58 "PDU session type Unstructured only allowed", #61 "PDU session type Ethernet only allowed", #67 "insufficient resources for specific slice and DNN", #68 "not supported SSC mode", and #69 "insufficient resources for specific slice", and #33 "requested service option not subscribed" upon sending PDU SESSION ESTABLISHMENT REQUEST to establish an MA PDU session, and the Back-off timer value IE is included, the UE shall behave as follows: (if the UE is a UE configured for high priority access in selected PLMN, exceptions are specified in subclause 6.2.12):

如果5GSM原因值不同于#26“资源不足”、#28“未知PDU会话类型”、#39“请求重新激活”、#46“超出LADN服务区域”、#50“只允许IPv4的PDU会话类型”、#51“只允许IPv6的PDU会话类型”、#54“PDU会话不存在”、#57“只允许IPv4v6的PDU会话类型”、#58“只允许非结构化的PDU会话类型”，#61“仅允许PDU会话类型以太网”、#67“特定切片和DNN的资源不足”、#68“不支持SSC模式”、#69“特定切片的资源不足”和#33“未订阅请求的服务选项”发送PDU会话建立请求以建立MA PDU会话，并包括退避计时器值IE，UE的行为如下：（如果UE是为选定PLMN中的高优先级访问配置的UE，则第6.2.12款规定了例外情况）：
a)    if the timer value indicates neither zero nor deactivated and:
a） 如果计时器值既不指示零也不指示停用，并且：

1)    if the UE provided a DNN and S-NSSAI to the network during the PDU session establishment and the 5GSM cause value is different from #27 "missing or unknown DNN", the UE shall start the back-off timer with the value provided in the Back-off timer value IE for the PDU session establishment procedure and [PLMN, DNN, (mapped) HPLMN S-NSSAI] combination. The UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message for the same DNN and (mapped) HPLMN S-NSSAI in the current PLMN, until the back-off timer expires, the UE is switched off, the USIM is removed, or the entry in the "list of subscriber data" for the current SNPN is updated if the UE does not support access to an SNPN using credentials from a credentials holder, or the selected entry of the "list of subscriber data" is updated if the UE supports access to an SNPN using credentials from a credentials holder;

1） 如果UE在PDU会话建立期间向网络提供DNN和S-NSSAI，并且5GSM原因值不同于#27“缺失或未知DNN”，则UE应使用用于PDU会话建立过程的退避计时器值IE和[PLMN，DNN，（映射）HPLMN S-NSSAI]组合中提供的值启动退避计时器。如果UE不支持使用来自凭证持有人的凭证接入SNPN，则UE不得为当前PLMN中的同一DNN和（映射）HPLMN S-NSSAI发送另一个PDU会话建立请求消息，直到退避计时器过期、UE关闭、USIM删除或更新当前SNPN的“订户数据列表”中的条目，或者，如果UE支持使用来自凭证持有人的凭证接入SNPN，则更新“用户数据列表”的所选条目；

2)    if the UE provided a DNN to the network during the PDU session establishment and the 5GSM cause value is #27 "missing or unknown DNN", the UE shall start the back-off timer with the value provided in the Back-off timer value IE for the PDU session establishment procedure and [PLMN, DNN] combination. The UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message for the same DNN in the current PLMN, until the back-off timer expires, the UE is switched off, the USIM is removed, or the entry in the "list of subscriber data" for the current SNPN is updated if the UE does not support access to an SNPN using credentials from a credentials holder, or the selected entry of the "list of subscriber data" is updated if the UE supports access to an SNPN using credentials from a credentials holder;

2） 如果UE在PDU会话建立期间向网络提供了DNN，并且5GSM原因值为#27“缺失或未知DNN”，则UE应使用用于PDU会话建立过程和[PLMN，DNN]组合的退避计时器值IE中提供的值启动退避计时器。如果UE不支持使用来自凭证持有人的凭证接入SNPN，则UE不得为当前PLMN中的同一DNN发送另一PDU会话建立请求消息，直到退避计时器过期、UE关闭、USIM删除或更新当前SNPN的“用户数据列表”中的条目，或者，如果UE支持使用来自凭证持有人的凭证接入SNPN，则更新“用户数据列表”的所选条目；

3)    if the UE did not provide a DNN or S-NSSAI or any of the two parameters to the network during the PDU session establishment and the 5GSM cause value is different from #27 "missing or unknown DNN", it shall start the back-off timer accordingly for the PDU session establishment procedure and the [PLMN, DNN, no S-NSSAI], [PLMN, no DNN, (mapped) HPLMN S-NSSAI] or [PLMN, no DNN, no S-NSSAI] combination. Dependent on the combination, the UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message for the same [PLMN, DNN, no S-NSSAI], [PLMN, no DNN, (mapped) HPLMN S-NSSAI] or [PLMN, no DNN, no S-NSSAI] combination in the current PLMN, until the back-off timer expires, the UE is switched off, the USIM is removed, or the entry in the "list of subscriber data" for the current SNPN is updated if the UE does not support access to an SNPN using credentials from a credentials holder, or the selected entry of the "list of subscriber data" is updated if the UE supports access to an SNPN using credentials from a credentials holder; or
3） 如果UE在PDU会话建立期间未向网络提供DNN或S-NSSAI或这两个参数中的任何一个，并且5GSM原因值不同于#27“缺失或未知DNN”，则它应相应地启动PDU会话建立过程和[PLMN，DNN，无S-NSSAI]的退避计时器，[PLMN，无DNN，（映射）HPLMN S-NSSAI]或[PLMN，无DNN，无S-NSSAI]组合。根据该组合，UE不得为当前PLMN中的相同[PLMN，DNN，无S-NSSAI]、[PLMN，无DNN，（映射）HPLMN S-NSSAI]或[PLMN，无DNN，无S-NSSAI]组合发送另一PDU会话建立请求消息，直到退避计时器到期，UE关闭，USIM移除，或者，如果UE不支持使用来自凭证持有人的凭证接入SNPN，则更新当前SNPN的“用户数据列表”中的条目，或者如果UE支持使用来自凭证持有人的凭证接入SNPN，则更新“用户数据列表”的所选条目；或

4)    if the UE did not provide a DNN to the network during the PDU session establishment and the 5GSM cause value is #27 "missing or unknown DNN", it shall start the back-off timer accordingly for the PDU session establishment procedure and the [PLMN, no DNN] combination. The UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message for the same [PLMN, no DNN] in the current PLMN, until the back-off timer expires, the UE is switched off, the USIM is removed, or the entry in the "list of subscriber data" for the current SNPN is updated if the UE does not support access to an SNPN using credentials from a credentials holder, or the selected entry of the "list of subscriber data" is updated if the UE supports access to an SNPN using credentials from a credentials holder;

4） 如果UE在PDU会话建立期间未向网络提供DNN，并且5GSM原因值为#27“缺失或未知DNN”，则其应相应地启动用于PDU会话建立过程和[PLMN，无DNN]组合的退避计时器。如果UE不支持使用来自凭证持有人的凭证接入SNPN，则UE不得为当前PLMN中的相同[PLMN，无DNN]发送另一个PDU会话建立请求消息，直到退避计时器过期、UE关闭、USIM删除或更新当前SNPN的“用户数据列表”中的条目，或者，如果UE支持使用来自凭证持有人的凭证接入SNPN，则更新“用户数据列表”的所选条目；
b)    if the timer value indicates that this timer is deactivated and:
b） 如果计时器值指示此计时器已停用，并且：

1)    if the UE provided a DNN and S-NSSAI to the network during the PDU session establishment and the 5GSM cause value is different from #27 "missing or unknown DNN", the UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message for the same DNN and (mapped) HPLMN S-NSSAI in the current PLMN, until the UE is switched off, the USIM is removed, or the entry in the "list of subscriber data" for the current SNPN is updated if the UE does not support access to an SNPN using credentials from a credentials holder, or the selected entry of the "list of subscriber data" is updated if the UE supports access to an SNPN using credentials from a credentials holder;

1） 如果UE在PDU会话建立期间向网络提供了DNN和S-NSSAI，并且5GSM原因值不同于#27“缺失或未知DNN”，则UE不得为当前PLMN中的相同DNN和（映射）HPLMN S-NSSAI发送另一个PDU会话建立请求消息，直到UE关闭，USIM被移除，或者，如果UE不支持使用来自凭证持有人的凭证访问SNPN，则更新当前SNPN的“用户数据列表”中的条目，或者如果UE支持使用来自凭证持有人的凭证访问SNPN，则更新“用户数据列表”的所选条目；

2)    if the UE provided a DNN to the network during the PDU session establishment and the 5GSM cause value is #27 "missing or unknown DNN", the UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message for the same DNN in the current PLMN, until the UE is switched off, the USIM is removed, or the entry in the "list of subscriber data" for the current SNPN is updated if the UE does not support access to an SNPN using credentials from a credentials holder, or the selected entry of the "list of subscriber data" is updated if the UE supports access to an SNPN using credentials from a credentials holder;

2） 如果UE在PDU会话建立期间向网络提供了DNN，并且5GSM原因值为#27“缺失或未知DNN”，则UE不得为当前PLMN中的同一DNN发送另一个PDU会话建立请求消息，直到UE关闭，USIM被移除，或者，如果UE不支持使用来自凭证持有人的凭证访问SNPN，则更新当前SNPN的“用户数据列表”中的条目，或者如果UE支持使用来自凭证持有人的凭证访问SNPN，则更新“用户数据列表”的所选条目；

3)    if the UE did not provide a DNN or S-NSSAI or any of the two parameters to the network during the PDU session establishment and the 5GSM cause value is different from #27 "missing or unknown DNN", the UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message for the same [PLMN, DNN, no S-NSSAI], [PLMN, no DNN, (mapped) HPLMN S-NSSAI] or [PLMN, no DNN, no S-NSSAI] combination in the current PLMN, until the UE is switched off, the USIM is removed, or the entry in the "list of subscriber data" for the current SNPN is updated if the UE does not support access to an SNPN using credentials from a credentials holder, or the selected entry of the "list of subscriber data" is updated if the UE supports access to an SNPN using credentials from a credentials holder; or

3） 如果UE在PDU会话建立期间未向网络提供DNN或S-NSSAI或这两个参数中的任何一个，并且5GSM原因值不同于#27“缺失或未知DNN”，则UE不得为同一[PLMN，DNN，无S-NSSAI]发送另一个PDU会话建立请求消息，当前PLMN中的[PLMN，无DNN，（映射）HPLMN S-NSSAI]或[PLMN，无DNN，无S-NSSAI]组合，直到UE关闭、USIM删除，或者如果UE不支持使用来自凭据持有人的凭据访问SNPN，则更新当前SNPN的“订户数据列表”中的条目，或者，如果UE支持使用来自凭证持有人的凭证访问SNPN，则更新“用户数据列表”的所选条目；或

4)    if the UE did not provide a DNN to the network during the PDU session establishment and the 5GSM cause value is #27 "missing or unknown DNN", the UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message for the same [PLMN, no DNN] in the current PLMN, until the UE is switched off, the USIM is removed, or the entry in the "list of subscriber data" for the current SNPN is updated if the UE does not support access to an SNPN using credentials from a credentials holder, or the selected entry of the "list of subscriber data" is updated if the UE supports access to an SNPN using credentials from a credentials holder; and

4） 如果UE在PDU会话建立期间没有向网络提供DNN，并且5GSM原因值为#27“缺失或未知DNN”，则UE不得为当前PLMN中的相同[PLMN，无DNN]发送另一个PDU会话建立请求消息，直到UE关闭，USIM被移除，或者，如果UE不支持使用来自凭证持有人的凭证访问SNPN，则更新当前SNPN的“用户数据列表”中的条目，或者如果UE支持使用来自凭证持有人的凭证访问SNPN，则更新“用户数据列表”的所选条目；和

c)    if the timer value indicates zero and the 5GSM cause value is different from #27 "missing or unknown DNN", the UE may send another PDU SESSION ESTABLISHMENT REQUEST message for the same combination of [PLMN, DNN, (mapped) HPLMN S-NSSAI], [PLMN, DNN, no S-NSSAI], [PLMN, no DNN, (mapped) HPLMN S-NSSAI], or [PLMN, no DNN, no S-NSSAI] in the current PLMN. If the timer value indicates zero and the 5GSM cause value is #27 "missing or unknown DNN", the UE may send another PDU SESSION ESTABLISHMENT REQUEST message for the same combination of [PLMN, DNN], or [PLMN, no DNN] in the current PLMN.

c） 如果计时器值指示零并且5GSM原因值不同于#27“缺失或未知DNN”，则UE可以针对当前PLMN中的[PLMN，DNN，（映射）HPLMN S-NSSAI]、[PLMN，DNN，no S-NSSAI]、[PLMN，no DNN，（映射）HPLMN S-NSSAI]或[PLMN，no DNN，no S-NSSAI]的相同组合发送另一PDU会话建立请求消息。如果计时器值指示零，并且5GSM原因值为#27“缺失或未知DNN”，则UE可以针对当前PLMN中的[PLMN，DNN]或[PLMN，no DNN]的相同组合发送另一PDU会话建立请求消息。
If the Back-off timer value IE is not included, then the UE shall ignore the Re-attempt indicator IE provided by the network in the PDU SESSION ESTABLISHMENT REJECT message, if any.
如果不包括退避计时器值IE，则UE应忽略PDU会话建立拒绝消息中由网络提供的重试指示器IE（如果有）。

a)    Additionally, if the 5GSM cause value is #8 "operator determined barring", #32 "service option not supported", #33 "requested service option not subscribed" upon sending PDU SESSION ESTABLISHMENT REQUEST not to establish an MA PDU session, or #70 "missing or unknown DNN in a slice", then:
a） 此外，如果在发送PDU会话建立请求以不建立MA PDU会话时，5GSM原因值为#8“运营商确定的限制”、#32“服务选项不受支持”、#33“请求的服务选项未订阅”或#70“切片中的DNN缺失或未知”，则：
1)    the UE not operating in SNPN access operation mode shall proceed as follows:
1） 不在SNPN接入操作模式下运行的UE应按以下方式进行：
i)    if the UE is registered in the HPLMN or in a PLMN that is within the EHPLMN list, the UE shall behave as described above in the present subclause using the configured SM Retry Timer value as specified in 3GPP TS 24.368 [17] or in USIM file NASCONFIG as specified in 3GPP TS 31.102 [22], if available, as back-off timer value; and
i） 如果UE在HPLMN或EHPLMN列表内的PLMN中注册，则UE应使用3GPP TS 24.368[17]中指定的配置SM重试计时器值或3GPP TS 31.102[22]中指定的USIM文件NASCONFIG（如果可用）作为退避计时器值，按照本节中的描述行事；和

NOTE 1:    The way to choose one of the configured SM Retry Timer values for back-off timer value is up to UE implementation if the UE is configured with:
-    an SM Retry Timer value in ME as specified in 3GPP TS 24.368 [17]; and
-    an SM Retry Timer value in USIM file NASCONFIG as specified in 3GPP TS 31.102 [22].
注1：如果UE配置了以下各项，则为退避计时器值选择一个已配置的SM重试计时器值的方法取决于UE实现：
-3GPP TS 24.368[17]中规定的ME中的SM重试计时器值；和
-3GPP TS 31.102[22]中规定的USIM文件NASCONFIG中的SM重试计时器值。
ii)    otherwise, if the UE is not registered in its HPLMN or in a PLMN that is within the EHPLMN list, or if the SM Retry Timer value is not configured, the UE shall behave as described above in the present subclause, using the default value of 12 minutes for the back-off timer; or
ii）否则，如果UE未在其HPLMN或EHPLMN列表内的PLMN中注册，或者如果未配置SM重试计时器值，则UE应按照本节中的上述操作，使用12分钟的默认值作为退避计时器；或

2)    the UE operating in SNPN access operation mode shall proceed as follows:
2） 在SNPN接入操作模式下运行的UE应如下进行：
i)    if:
A)    the SM Retry Timer value for the current SNPN as specified in 3GPP TS 24.368 [17] is available; or
B)    the UE used the USIM for registration to the current SNPN and the SM Retry Timer value in USIM file NASCONFIG as specified in 3GPP TS 31.102 [22] is available;
i） 如果：
A） 3GPP TS 24.368[17]中规定的当前SNPN的SM重试计时器值可用；或
B） UE使用USIM注册到当前SNPN，并且可以使用3GPP TS 31.102[22]中指定的USIM文件NASCONFIG中的SM重试计时器值；
then the UE shall behave as described above in the present subclause using the configured SM Retry Timer value as back-off timer value; or
然后，UE应使用配置的SM重试计时器值作为退避计时器值，如本节中所述；或
NOTE 2:    The way to choose one of the configured SM Retry Timer values for back-off timer value is up to UE implementation if both conditions in bullets A) and B) above are satisfied.
注2：如果上述项目符号A）和B）中的两个条件都满足，则为后退计时器值选择配置的SM重试计时器值之一的方法取决于UE实现。
ii)    otherwise, the UE shall behave as described above in the present subclause, using the default value of 12 minutes for the back-off timer.
ii）否则，UE的行为应如本节所述，使用12分钟的默认值作为退避计时器。
b)    For 5GSM cause value #27 "missing or unknown DNN", then:
b） 对于5GSM原因值#27“缺失或未知DNN”，则：
1)    the UE not operating in SNPN access operation mode shall proceed as follows:
1） 不在SNPN接入操作模式下运行的UE应按以下方式进行：
i)    if the UE is registered in the HPLMN or in a PLMN that is within the EHPLMN list, the UE shall start the back-off timer with the configured SM Retry Timer value as specified in 3GPP TS 24.368 [17] or in USIM file NASCONFIG as specified in 3GPP TS 31.102 [22], if available, as back-off timer value for the PDU session establishment procedure and the [PLMN, DNN] or [PLMN, no DNN] combination. The UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message for the same DNN in the current PLMN, until the back-off timer expires, the UE is switched off or the USIM is removed; and

i） 如果UE在HPLMN或EHPLMN列表内的PLMN中注册，则UE应使用3GPP TS 24.368[17]中规定的配置SM重试计时器值或3GPP TS 31.102[22]中规定的USIM文件NASCONFIG（如果可用）启动后退计时器，作为PDU会话建立过程和[PLMN，DNN]或[PLMN，no DNN]组合的退避计时器值。在退避计时器到期、UE关闭或USIM删除之前，UE不得为当前PLMN中的同一DNN发送另一个PDU会话建立请求消息；和
NOTE 3:    The way to choose one of the configured SM Retry Timer values for back-off timer value is up to UE implementation if the UE is configured with:
-    an SM Retry Timer value in ME as specified in 3GPP TS 24.368 [17]; and
-    an SM Retry Timer value in USIM file NASCONFIG as specified in 3GPP TS 31.102 [22].
注3：如果UE配置了以下各项，则为退避计时器值选择一个已配置的SM重试计时器值的方法取决于UE实现：
-3GPP TS 24.368[17]中规定的ME中的SM重试计时器值；和
-3GPP TS 31.102[22]中规定的USIM文件NASCONFIG中的SM重试计时

ii)    otherwise, if the UE is not registered in its HPLMN or in a PLMN that is within the EHPLMN list, or if the SM Retry Timer value is not configured, the UE shall start the back-off timer with the default value of 12 minutes as back-off timer value for the PDU session establishment procedure and the [PLMN, DNN] or [PLMN, no DNN] combination. The UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message for the same DNN in the current PLMN, until the back-off timer expires, the UE is switched off or the USIM is removed; or
ii）否则，如果UE未在其HPLMN或EHPLMN列表内的PLMN中注册，或者如果未配置SM重试计时器值，则UE应启动退避计时器，默认值为12分钟，作为PDU会话建立过程和[PLMN，DNN]或[PLMN，no DNN]组合的退避计时器值。在退避计时器到期、UE关闭或USIM删除之前，UE不得为当前PLMN中的同一DNN发送另一个PDU会话建立请求消息；或

2)    the UE operating in SNPN access operation mode shall proceed as follows:
i)    if:
A)    the SM Retry Timer value for the current SNPN as specified in 3GPP TS 24.368 [17] is available; or
B)    the UE used the USIM for registration to the current SNPN and the SM Retry Timer value in USIM file NASCONFIG as specified in 3GPP TS 31.102 [22] is available;
2） 在SNPN接入操作模式下运行的UE应如下进行：
i） 如果：
A） 3GPP TS 24.368[17]中规定的当前SNPN的SM重试计时器值可用；或
B） UE使用USIM注册到当前SNPN，并且可以使用3GPP TS 31.102[22]中指定的USIM文件NASCONFIG中的SM重试计时器值；
then:

-    if the UE does not support access to an SNPN using credentials from a credentials holder, the UE shall start the back-off timer with the configured SM Retry Timer value as back-off timer value for the PDU session establishment procedure and the [SNPN, DNN] or [SNPN, no DNN] combination. The UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message for the same DNN in the current SNPN, until the back-off timer expires, the UE is switched off, or the entry in the "list of subscriber data" for the current SNPN is updated; and

-    if the UE supports access to an SNPN using credentials from a credentials holder, the UE shall start the back-off timer with the configured SM Retry Timer value as back-off timer value for the PDU session establishment procedure and the [SNPN, selected entry of the "list of subscriber data" or selected PLMN subscription, DNN] or [SNPN, selected entry of the "list of subscriber data" or selected PLMN subscription, no DNN] combination. The UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message for the same DNN in the current SNPN using the selected entry in the "list of subscriber data" or selected PLMN subscription, until the back-off timer expires, the UE is switched off, the UICC containing the USIM is removed or the selected entry of the "list of subscriber data" is updated; or

然后：
-如果UE不支持使用来自凭证持有人的凭证访问SNPN，则UE应使用配置的SM重试计时器值作为PDU会话建立过程的退避计时器值以及[SNPN，DNN]或[SNPN，no DNN]组合启动退避计时器。在退避计时器到期、UE关闭或更新当前SNPN的“用户数据列表”中的条目之前，UE不得为当前SNPN中的同一DNN发送另一个PDU会话建立请求消息；和
-如果UE支持使用来自凭证持有人的凭证访问SNPN，UE应使用配置的SM重试计时器值作为PDU会话建立过程的退避计时器值和[SNPN，选择的“用户数据列表”条目或选择的PLMN订阅，DNN]或[SNPN，选择的“用户数据列表”条目或选择的PLMN订阅，无DNN]组合来启动退避计时器。在退避计时器到期、UE关闭、包含USIM的UICC删除或“用户数据列表”的选定条目更新之前，UE不得使用“用户数据列表”中的选定条目或选定PLMN订阅为当前SNPN中的同一DNN发送另一PDU会话建立请求消息；或

NOTE 4:    The way to choose one of the configured SM Retry Timer values for back-off timer value is up to UE implementation if both conditions in bullets A) and B) above are satisfied.
注4：如果上述项目符号A）和B）中的两个条件都满足，则为退避计时器值选择一个配置的SM重试计时器值的方法取决于UE实现。
ii)    otherwise:
-    if the UE does not support access to an SNPN using credentials from a credentials holder,  the UE shall start the back-off timer with the default value of 12 minutes as back-off timer value for the PDU session establishment procedure and the [SNPN, DNN] or [SNPN, no DNN] combination. The UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message for the same DNN in the current SNPN, until the back-off timer expires, the UE is switched off, or the entry in the "list of subscriber data" for the current SNPN is updated; and

-    if the UE supports access to an SNPN using credentials from a credentials holder, the UE shall start the back-off timer with the default value of 12 min as back-off timer value for the PDU session establishment procedure and the [SNPN, selected entry of the "list of subscriber data" or selected PLMN subscription, DNN] or [SNPN, selected entry in the "list of subscriber data" or selected PLMN subscription, no DNN] combination. The UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message for the same DNN in the current SNPN using the selected entry of the "list of subscriber data", until the back-off timer expires, the UE is switched off, the UICC containing the USIM is removed or the selected entry of the "list of subscriber data" is updated; and

ii）否则：
-如果UE不支持使用来自凭证持有人的凭证访问SNPN，则UE应启动退避计时器，默认值为12分钟，作为PDU会话建立过程和[SNPN，DNN]或[SNPN，no DNN]组合的退避计时器值。在退避计时器到期、UE关闭或更新当前SNPN的“用户数据列表”中的条目之前，UE不得为当前SNPN中的同一DNN发送另一个PDU会话建立请求消息；和
-如果UE支持使用来自凭证持有人的凭证访问SNPN，UE应启动退避计时器，默认值为12分钟，作为PDU会话建立过程的退避计时器值和[SNPN，选择的“用户数据列表”条目或选择的PLMN订阅，DNN]或[SNPN，选择的“用户数据列表”条目或选择的PLMN订阅，无DNN]组合。在退避计时器到期、UE关闭、包含USIM的UICC移除或“用户数据列表”的选定条目更新之前，UE不得使用“用户数据列表”的选定条目为当前SNPN中的同一DNN发送另一PDU会话建立请求消息；和

c)    For 5GSM cause values different from #8 "operator determined barring",  #27 "missing or unknown DNN", #32 "service option not supported", #33 "requested service option not subscribed" and #70 "missing or unknown DNN in a slice", the UE behaviour regarding the start of a back-off timer is unspecified.
c） 对于不同于#8“运营商确定的限制”、#27“缺失或未知DNN”、#32“不支持服务选项”、#33“请求的服务选项未订阅”和#70“切片中缺失或未知DNN”的5GSM原因值，未指定UE关于启动退避计时器的行为。
The UE shall not stop any back-off timer:
a)    upon a PLMN change;
b)    upon an inter-system change; or
c)    upon registration over another access type.

UE不得停止任何后退计时器：
a） PLMN变更时；
b） 系统间变更时；或
c） 通过另一种接入类型注册时。
If the network indicates that a back-off timer for the PDU session establishment procedure is deactivated, then it remains deactivated;
a)    upon a PLMN change;
b)    upon an inter-system change; or
c)    upon registration over another access type.

如果网络指示PDU会话建立过程的退避计时器被停用，则其保持停用状态；
a） PLMN变更时；
b） 系统间变更时；或
c） 通过另一种接入类型注册时。
NOTE 5:    This means the back-off timer can still be running or be deactivated for the given 5GSM procedure when the UE returns to the PLMN or when it performs inter-system change back from S1 mode to N1 mode. Thus, the UE can still be prevented from sending another PDU SESSION ESTABLISHMENT REQUEST message for the combination of [PLMN, DNN, (mapped) HPLMN S-NSSAI], [PLMN, DNN, no S-NSSAI], [PLMN, no DNN, (mapped) HPLMN S-NSSAI], [PLMN, no DNN, no S-NSSAI] , [PLMN, DNN], or [PLMN, no DNN] in the PLMN.
注5：这意味着当UE返回PLMN或当其执行系统间从S1模式切换回N1模式时，对于给定的5GSM过程，退避计时器仍然可以运行或停用。因此，仍然可以防止UE为PLMN中的[PLMN，DNN，（映射）HPLMN S-NSSAI]、[PLMN，DNN，no S-NSSAI]、[PLMN，no DNN，（映射）HPLMN S-NSSAI]、[PLMN，no DNN，no S-NSSAI]、[PLMN，no DNN]或[PLMN，no DNN]的组合发送另一个PDU会话建立请求消息。

If the back-off timer is started upon receipt of a PDU SESSION ESTABLISHMENT REJECT (i.e. the timer value was provided by the network, a configured value is available or the default value is used as explained above) or the back-off timer is deactivated, the UE behaves as follows:
如果在接收到PDU会话建立拒绝时启动退避计时器（即，计时器值由网络提供，配置值可用或如上所述使用默认值），或者退避计时器被停用，则UE的行为如下：
a)    after a PLMN change:
a） PLMN变更后：

1)    the UE may send a PDU SESSION ESTABLISHMENT REQUEST message for the combination of [new PLMN, DNN, (mapped) HPLMN S-NSSAI], [new PLMN, DNN, no S-NSSAI], [new PLMN, no DNN, (mapped) HPLMN S-NSSAI], or [new PLMN, no DNN, no S-NSSAI] in the new PLMN, if the back-off timer is not running and is not deactivated for the PDU session establishment procedure and the combination of [new PLMN, DNN, (mapped) HPLMN S-NSSAI], [new PLMN, DNN, no S-NSSAI], [new PLMN, no DNN, (mapped) HPLMN S-NSSAI], or [new PLMN, no DNN, no S-NSSAI];

1） UE可以发送PDU会话建立请求消息，用于在新PLMN中组合[新PLMN，DNN，（映射）HPLMN S-NSSAI]、[新PLMN，DNN，无S-NSSAI]、[新PLMN，无DNN，（映射）HPLMN S-NSSAI]或[新PLMN，无DNN，无S-NSSAI]，如果退避计时器未运行且未针对PDU会话建立过程和[new PLMN，DNN，（mapped）HPLMN S-NSSAI]、[new PLMN，DNN，no S-NSSAI]、[new PLMN，no DNN，（mapped）HPLMN S-NSSAI]或[new PLMN，no DNN，no S-NSSAI]的组合停用；

2)    as an implementation option, for the 5GSM cause value #8 "operator determined barring", #32 "service option not supported", #33 "requested service option not subscribed" and #70 "missing or unknown DNN in a slice", if the network does not include a Re-attempt indicator IE, the UE may decide not to automatically send another PDU SESSION ESTABLISHMENT REQUEST message for the same combination of [PLMN, DNN, (mapped) HPLMN S-NSSAI], [PLMN, DNN, no S-NSSAI], [PLMN, no DNN, (mapped) HPLMN S-NSSAI], or [PLMN, no DNN, no S-NSSAI] using the same PDU session type if the UE is registered to a new PLMN which is in the list of equivalent PLMNs; and

2） 作为实现选项，对于5GSM原因值#8“操作员确定的限制”、#32“服务选项不受支持”、#33“请求的服务选项未订阅”和#70“切片中缺少或未知DNN”，如果网络不包括重试指示符IE，如果UE注册到等效PLMN列表中的新PLMN，则UE可以决定不使用相同的PDU会话类型为[PLMN，DNN，（映射）HPLMN S-NSSAI]、[PLMN，DNN，no S-NSSAI]、[PLMN，no DNN，（映射）HPLMN S-NSSAI]或[PLMN，no DNN，no S-NSSAI]的相同组合自动发送另一个PDU会话建立请求消息；和

3)    as an implementation option, for the 5GSM cause value #27 "missing or unknown DNN", if the network does not include a Re-attempt indicator IE, the UE may decide not to automatically send another PDU SESSION ESTABLISHMENT REQUEST message for the same combination of [PLMN, DNN] or [PLMN, no DNN] using the same PDU session type if the UE is registered to a new PLMN which is in the list of equivalent PLMNs;
3） 作为实现选项，对于5GSM原因值#27“缺失或未知DNN”，如果网络不包括重试指示器IE，如果UE注册到等效PLMN列表中的新PLMN，则UE可以决定不使用相同的PDU会话类型为[PLMN，DNN]或[PLMN，no DNN]的相同组合自动发送另一个PDU会话建立请求消息；

b)    if the network does not include the Re-attempt indicator IE to indicate whether re-attempt in S1 mode is allowed, or the UE ignores the Re-attempt indicator IE, e.g. because the Back-off timer value IE is not included, then:
b） 如果网络不包括指示是否允许在S1模式下重新尝试的重新尝试指示符IE，或者UE忽略重新尝试指示符IE，例如，因为不包括退避计时器值IE，则：

1)    if the UE is registered in its HPLMN or in a PLMN that is within the EHPLMN list and the back-off timer is running for the combination of [PLMN, DNN, (mapped) HPLMN S-NSSAI] or [PLMN, DNN, no S-NSSAI], the UE shall apply the configured SM_RetryAtRATChange value as specified in 3GPP TS 24.368 [17] or in USIM file NASCONFIG as specified in 3GPP TS 31.102 [22], if available, to determine whether the UE may attempt a PDN connectivity procedure for the same [PLMN, DNN] combination in S1 mode. If the back-off timer is running for the combination of [PLMN, no DNN, (mapped) HPLMN S-NSSAI] or [PLMN, no DNN, no S-NSSAI], the same applies for the PDN connectivity procedure for the [PLMN, no DNN] combination in S1 mode accordingly; and

1） 如果UE在其HPLMN或EHPLMN列表内的PLMN中注册，并且退避计时器正在为[PLMN，DNN，（映射）HPLMN S-NSSAI]或[PLMN，DNN，no S-NSSAI]的组合运行，则UE应应用3GPP TS 24.368[17]或3GPP TS 31.102[22]中指定的USIM文件NASCONFIG（如果可用）中指定的配置SM_ RetryATChange值，确定UE是否可以在S1模式下为相同的[PLMN，DNN]组合尝试PDN连接过程。如果回退计时器正在为[PLMN，无DNN，（映射）HPLMN S-NSSAI]或[PLMN，无DNN，无S-NSSAI]的组合运行，则同样适用于S1模式下[PLMN，无DNN]组合的PDN连接过程；和

NOTE 6:    The way to choose one of the configured SM_RetryAtRATChange values for back-off timer value is up to UE implementation if the UE is configured with:
-    an SM_RetryAtRATChange value in ME as specified in 3GPP TS 24.368 [17]; and
-    an SM_RetryAtRATChange value in USIM file NASCONFIG as specified in 3GPP TS 31.102 [22].
注6：如果UE配置了以下各项，则为后退计时器值选择一个配置的SM_RetryAtRATChange值的方法取决于UE实现：
-3GPP TS 24.368[17]中规定的ME中的SM_RetryAtRATChange值；和
-3GPP TS 31.102[22]中规定的USIM文件NASCONFIG中的SM_RetryAtRATChange值。

2)    if the UE is not registered in its HPLMN or in a PLMN that is within the EHPLMN list, or if the NAS configuration MO as specified in 3GPP TS 24.368 [17] is not available and the value for inter-system change is not configured in the USIM file NASCONFIG, then the UE behaviour regarding a PDN connectivity procedure for the same [PLMN, DNN] or [PLMN, no DNN] combination in S1 mode is unspecified; and
2） 如果UE未在其HPLMN或EHPLMN列表内的PLMN中注册，或者如果3GPP TS 24.368[17]中指定的NAS配置MO不可用，并且USIM文件NASCONFIG中未配置系统间更改的值，然后，未指定关于S1模式中相同[PLMN，DNN]或[PLMN，no DNN]组合的PDN连接过程的UE行为；和

c)    if the network includes the Re-attempt indicator IE indicating that re-attempt in an equivalent PLMN is not allowed, then depending on the timer value received in the Back-off timer value IE, for each combination of a PLMN from the equivalent PLMN list and the respective [DNN, (mapped) HPLMN S-NSSAI], [DNN, no S-NSSAI], [no DNN, (mapped) HPLMN S-NSSAI], or [no DNN, no S-NSSAI] combination, the UE shall start a back-off timer for the PDU session establishment procedure with the value provided by the network, or deactivate the respective back-off timer as follows:

c） 如果网络包括指示不允许在等效PLMN中重新尝试的重新尝试指示符IE，则根据退避计时器值IE中接收到的计时器值，对于来自等效PLMN列表的PLMN的每个组合和相应的[DNN，（映射）HPLMN S-NSSAI]、[DNN，无S-NSSAI]、[DNN，（映射）HPLMN S-NSSAI]或[no DNN，无S-NSSAI]组合，UE应使用网络提供的值启动PDU会话建立过程的退避计时器，或按如下方式停用相应的后退计时器：
1)    if the Re-attempt indicator IE additionally indicates that re-attempt in S1 mode is allowed, the UE shall start or deactivate the back-off timer for N1 mode only; and
1） 如果重新尝试指示器IE额外指示允许在S1模式下重新尝试，则UE应仅为N1模式启动或停用退避计时器；和
2)    otherwise, the UE shall start or deactivate the back-off timer for S1 and N1 mode.
2） 否则，UE应启动或停用S1和N1模式的退避计时器。

If the back-off timer for a [PLMN, DNN] or [PLMN, no DNN] combination, was started or deactivated in S1 mode upon receipt of PDN CONNECTIVITY REJECT message (see 3GPP TS 24.301 [15]) and the network indicated that re-attempt in N1 mode is allowed, then this back-off timer does not prevent the UE from sending a PDU SESSION ESTABLISHMENT REQUEST message in this PLMN for the same DNN, or without DNN, after inter-system change to N1 mode. If the network indicated that re-attempt in N1 mode is not allowed, the UE shall not send any PDU SESSION ESTABLISHMENT REQUEST message in this PLMN for the same DNN in combination with any S-NSSAI or without S-NSSAI, or in this PLMN without DNN in combination with any S-NSSAI or without S-NSSAI, after inter-system change to N1 mode until the timer expires, the UE is switched off or the USIM is removed.

如果[PLMN，DNN]或[PLMN，无DNN]组合的退避计时器在收到PDN连接拒绝消息（参见3GPP TS 24.301[15]）时在S1模式下启动或停用，并且网络指示允许在N1模式下重新尝试，则该退避计时器不会阻止UE在该PLMN中为同一DNN发送PDU会话建立请求消息，或无DNN，在系统间切换到N1模式后。如果网络指示不允许在N1模式下重新尝试，则在系统间切换到N1模式后，UE不得在该PLMN中为相同DNN发送任何PDU会话建立请求消息，包括任何S-NSSAI或不包括S-NSSAI的组合，或在该PLMN中不包括DNN的组合，包括任何S-NSSAI或不包括S-NSSAI的组合，直到计时器过期，UE关闭或USIM移除。

NOTE 7:    The back-off timer is used to describe a logical model of the required UE behaviour. This model does not imply any specific implementation, e.g. as a timer or timestamp.
注7：退避计时器用于描述所需UE行为的逻辑模型。该模型并不意味着任何具体的实现，例如作为计时器或时间戳。
NOTE 8:    Reference to back-off timer in this section can either refer to use of timer T3396 or to use of a different packet system specific timer within the UE. Whether the UE uses T3396 as a back-off timer or it uses different packet system specific timers as back-off timers is left up to UE implementation.
注8：本节中对退避计时器的引用可以是指计时器T3396的使用，也可以是指在UE内使用不同的分组系统特定计时器。UE是使用T3396作为退避计时器，还是使用不同的分组系统特定计时器作为退避计时器，取决于UE实现。
When the back-off timer is running or the timer is deactivated, the UE is allowed to initiate a PDU session establishment procedure if the procedure is for emergency services.
当退避计时器正在运行或计时器被停用时，如果该过程用于紧急服务，则允许UE启动PDU会话建立过程。

If the 5GSM cause value is #28 "unknown PDU session type" and the PDU SESSION ESTABLISHMENT REQUEST message contained a PDU session type IE indicating a PDU session type, the UE shall ignore the Back-off timer value IE and Re-attempt indicator IE provided by the network, if any. The UE may send another PDU SESSION ESTABLISHMENT REQUEST message to establish a new PDU session with the PDU session type IE indicating another PDU session type, e.g. using another value which can be used for the rejected component in the same route selection descriptor as specified in 3GPP TS 24.526 [19]. The behaviour of the UE for 5GSM cause value #28 also applies if the PDU session is a MA PDU Session.

如果5GSM原因值为#28“未知PDU会话类型”，并且PDU会话建立请求消息包含指示PDU会话类型的PDU会话类型IE，则UE应忽略网络提供的退避计时器值IE和重新尝试指示器IE（如果有）。UE可以发送另一个PDU会话建立请求消息，以建立新的PDU会话，其中PDU会话类型IE指示另一个PDU会话类型，例如，使用另一个值，该值可以用于3GPP TS 24.526[19]中指定的相同路由选择描述符中的被拒绝组件。如果PDU会话是MA PDU会话，则5GSM原因值#28的UE行为也适用。

If the 5GSM cause value is #39 "reactivation requested", the UE shall ignore the Back-off timer value IE and Re-attempt indicator IE provided by the network, if any.
如果5GSM原因值为#39“重新激活请求”，UE应忽略网络提供的退避计时器值IE和重新尝试指示器IE（如果有）。
NOTE 9:    Further UE behaviour upon receipt of 5GSM cause value #39 is up to the UE implementation.
注9：收到5GSM原因值#39后的进一步UE行为取决于UE实现。

If the 5GSM cause value is #46 "out of LADN service area", the UE shall ignore the Back-off timer value IE and Re-attempt indicator IE provided by the network, if any. If the UE is not located inside the LADN service area, the UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message or another PDU SESSION MODIFICATION REQUEST message for the LADN DNN provided by the UE during the PDU session establishment procedure until the LADN information for the specific LADN DNN is updated as described in subclause 5.4.4 and subclause 5.5.1. If the UE is not located inside the LADN service area, the UE shall not indicate the PDU session(s) for the LADN DNN provided by the UE during the PDU session establishment procedure in the Uplink data status IE included in the SERVICE REQUEST message until the LADN information for the specific LADN DNN is updated as described in subclause 5.4.4 and subclause 5.5.1.

如果5GSM原因值为#46“超出LADN服务区域”，则UE应忽略网络提供的退避计时器值IE和重新尝试指示器IE（如果有）。如果UE不位于LADN服务区域内，则在PDU会话建立过程中，UE不得为UE提供的LADN DNN发送另一个PDU会话建立请求消息或另一个PDU会话修改请求消息，直到特定LADN DNN的LADN信息按照5.4.4节和5.5.1节中的描述进行更新。如果UE不位于LADN服务区域内，则UE不得在PDU会话建立过程中以上行链路数据状态（包括在服务请求消息中）指示UE提供的LADN DNN的PDU会话，直到特定LADN DNN的LADN信息按照5.4.4节和5.5.1节中所述进行更新。

NOTE 10:    Based on UE implementation, the UE locating inside the LADN service area can send another PDU SESSION ESTABLISHMENT REQUEST message or PDU SESSION MODIFICATION REQUEST message for the LADN DNN which was rejected with the 5GSM cause value #46 "out of LADN service area".
注10：基于UE实现，位于LADN服务区域内的UE可以为被拒绝的LADN DNN发送另一个PDU会话建立请求消息或PDU会话修改请求消息，其5GSM原因值为#46“超出LADN服务区域”。

If the 5GSM cause value is #50 "PDU session type IPv4 only allowed", #51 "PDU session type IPv6 only allowed", #57 "PDU session type IPv4v6 only allowed", #58 "PDU session type Unstructured only allowed", or #61 "PDU session type Ethernet only allowed", the UE shall ignore the Back-off timer value IE provided by the network, if any. The UE shall evaluate the URSP rules if available as specified in 3GPP TS 24.526 [19]. The UE shall not subsequently send another PDU SESSION ESTABLISHMENT REQUEST message for the same DNN (or no DNN, if no DNN was indicated by the UE) and the same (mapped) HPLMN S-NSSAI (or no S-NSSAI, if no S-NSSAI was indicated by the UE) to obtain a PDU session type different from the one allowed by the network until any of the following conditions is fulfilled:

如果5GSM原因值为#50“只允许使用IPv4的PDU会话类型”、#51“仅允许使用IPv6的PDU对话类型”、#57“仅允许的PDU会议类型IPv4v6”、#58“仅允许非结构化的PDU会话类型”或#61“仅允许通过以太网的PDU对话框类型”，则UE应忽略网络提供的后退计时器值IE（如果有）。UE应根据3GPP TS 24.526[19]的规定评估URSP规则（如果可用）。在满足以下任一条件之前，UE不得随后为相同DNN（或无DNN，如果UE未指示DNN）和相同（映射）HPLMN S-NSSAI（或无S-NSSAI，如果UE未指示S-NSSAI）发送另一个PDU会话建立请求消息，以获得不同于网络允许的PDU会话类型：

a)    the UE is registered to a new PLMN which was not in the list of equivalent PLMNs at the time when the PDU SESSION ESTABLISHMENT REJECT message was received;
a） UE注册到新的PLMN，该PLMN在接收到PDU会话建立拒绝消息时不在等效PLMN的列表中；
b)    the UE is registered to a new PLMN which was in the list of equivalent PLMNs at the time when the PDU SESSION ESTABLISHMENT REJECT message was received, and either the network did not include a Re-attempt indicator IE in the PDU SESSION ESTABLISHMENT REJECT message or the Re-attempt indicator IE included in the message indicated that re-attempt in an equivalent PLMN is allowed;
b） UE注册到在接收到PDU会话建立拒绝消息时在等效PLMN列表中的新PLMN，并且网络未在PDU会话创建拒绝消息中包括重新尝试指示符IE，或者包括在指示允许在等效PLMN中重新尝试的消息中的重新尝试指示计IE；

c)    void;
c） 无效；
d)    the UE is switched off; or
d） UE关闭；或
e)    the USIM is removed, the entry in the "list of subscriber data" for the current SNPN is updated if the UE does not support access to an SNPN using credentials from a credentials holder, or the selected entry of the "list of subscriber data" is updated if the UE supports access to an SNPN using credentials from a credentials holder.
e） 如果UE不支持使用来自凭证持有人的凭证访问SNPN，则删除USIM，更新当前SNPN的“订户数据列表”中的条目，或者如果UE支持使用来自凭据持有人的凭据访问SNPN，“订户数据表”的所选条目被更新。

For the 5GSM cause values #50 "PDU session type IPv4 only allowed", #51 "PDU session type IPv6 only allowed", #57 "PDU session type IPv4v6 only allowed", #58 "PDU session type Unstructured only allowed", and #61 "PDU session type Ethernet only allowed", the UE shall ignore the value of the RATC bit in the Re-attempt indicator IE provided by the network, if any.
对于5GSM原因值#50“PDU会话类型IPv4 only allowed”、#51“PDU session type IPv6 only Allow”、#57“PDU session type IPv4v6 only allowed”、#58“PDU session type Unstructured only allowed”和# 61“PDU cession type Ethernet only allow”，UE应忽略网络提供的重试指示符IE中RATC位的值（如果有）。

NOTE 11:    For the 5GSM cause values #50 "PDU session type IPv4 only allowed", #51 "PDU session type IPv6 only allowed", #57 "PDU session type IPv4v6 only allowed", #58 "PDU session type Unstructured only allowed", and #61 "PDU session type Ethernet only allowed", re-attempt in S1 mode for the same DNN (or no DNN, if no DNN was indicated by the UE) is only allowed using the PDU session type(s) indicated by the network using the same PDU session type is not allowed.
注11：对于5GSM原因值#50“PDU会话类型IPv4 only allowed”、#51“PDU session type IPv6 only Allow”、#57“PDU session type IPv4v6 only allowed”、#58“PDU session type Unstructured only allowed”和#61“PDU-session type Ethernet only allow”，仅允许使用网络指示的PDU会话类型在S1模式下重新尝试相同的DNN（或没有DNN，如果UE未指示DNN），不允许使用相同的PDU对话类型。

If the 5GSM cause value is #54 "PDU session does not exist", the UE shall ignore the Back-off timer value IE and Re-attempt indicator IE provided by the network, if any. If the PDU session establishment procedure is to perform handover of an existing PDU session between 3GPP access and non-3GPP access, the UE shall release locally the existing PDU session with the PDU session ID included in the PDU SESSION ESTABLISHMENT REJECT message. The UE may initiate another UE-requested PDU session establishment procedure with the request type set to "initial request" in the subsequent PDU SESSION ESTABLISHMENT REQUEST message to establish a PDU session with the same DNN (or no DNN, if no DNN was indicated by the UE) and the same (mapped) HPLMN S-NSSAI (or no S-NSSAI, if no S-NSSAI was indicated by the UE).

如果5GSM原因值为#54“PDU会话不存在”，则UE应忽略网络提供的后退计时器值IE和重新尝试指示器IE（如果有）。如果PDU会话建立过程是在3GPP接入和非3GPP接入之间执行现有PDU会话的切换，则UE应在本地释放现有的PDU会话，其中PDU会话ID包括在PDU会话创建拒绝消息中。UE可以启动另一个UE请求的PDU会话建立过程，其请求类型在随后的PDU对话建立请求消息中设置为“initial request”，以建立具有相同DNN（或没有DNN，如果UE没有指示DNN）和相同（映射）HPLMN S-NSSAI（或没有S-NSSA，如果UE没有指示S-NSSAI）。

NOTE 12:    User interaction is necessary in some cases when the UE cannot re-establish the PDU session(s) automatically.
注12：在某些情况下，当UE无法自动重新建立PDU会话时，用户交互是必要的。

If the 5GSM cause value is #68 "not supported SSC mode", the UE shall ignore the Back-off timer value IE and Re-attempt indicator IE provided by the network, if any. The UE shall evaluate the URSP rules if available as specified in 3GPP TS 24.526 [19]. The UE shall not subsequently send another PDU SESSION ESTABLISHMENT REQUEST message for the same DNN (or no DNN, if no DNN was indicated by the UE) and the same (mapped) HPLMN S-NSSAI (or no S-NSSAI, if no S-NSSAI was indicated by the UE) using the same SSC mode or an SSC mode which was not included in the Allowed SSC mode IE until any of the following conditions is fulfilled:

如果5GSM原因值为#68“不支持SSC模式”，UE应忽略网络提供的退避计时器值IE和重新尝试指示器IE（如果有）。UE应根据3GPP TS 24.526[19]的规定评估URSP规则（如果可用）。在满足以下任何条件之前，UE不得随后使用相同的SSC模式或不包括在允许的SSC模式IE中的SSC模式，为相同的DNN（或没有DNN，如果UE未指示DNN）和相同（映射）的HPLMN S-NSSAI（或没有S-NSSA，如果UE未指示S-NSSAI）发送另一个PDU会话建立请求消息：

a)    the UE is registered to a new PLMN which was not in the list of equivalent PLMNs at the time when the PDU SESSION ESTABLISHMENT REJECT message was received;
a） UE注册到新的PLMN，该PLMN在接收到PDU会话建立拒绝消息时不在等效PLMN的列表中；
b)    the SSC mode which is used to access to the DNN (or no DNN, if no DNN was indicated by the UE) and the (mapped) HPLMN S-NSSAI (or no S-NSSAI, if no S-NSSAI was indicated by the UE) is changed by the UE which subsequently requests a new SSC mode in the Allowed SSC mode IE or no SSC mode;
b） 用于访问DNN（或无DNN，如果UE未指示DNN）和（映射）HPLMN S-NSSAI（或无S-NSSAI，如果UE未指示S-NSSAI）的SSC模式由UE更改，UE随后在允许的SSC模式IE或无SSC模式中请求新的SSC模式；

c)    the UE is switched off; or
c） UE关闭；或
d)    the USIM is removed, the entry in the "list of subscriber data" for the current SNPN is updated if the UE does not support access to an SNPN using credentials from a credentials holder, or the selected entry of the "list of subscriber data" is updated if the UE supports access to an SNPN using credentials from a credentials holder.
d） 如果UE不支持使用来自凭证持有人的凭证访问SNPN，则删除USIM，更新当前SNPN的“订户数据列表”中的条目，或者如果UE支持使用来自凭据持有人的凭据访问SNPN，“订户数据表”的所选条目被更新。

If the UE receives the 5GSM cause value is #33 "requested service option not subscribed" upon sending PDU SESSION ESTABLISHMENT REQUEST to establish an MA PDU session, the UE shall ignore the Back-off timer value IE and Re-attempt indicator IE provided by the network, if any. The UE shall evaluate URSP rules, if available, as specified in 3GPP TS 24.526 [19] and the UE may send PDU SESSION ESTABLISHMENT REQUEST after evaluating those URSP rules.
如果UE在发送PDU会话建立请求以建立MA PDU会话时接收到5GSM原因值为#33“请求的服务选项未订阅”，则UE应忽略网络提供的退避计时器值IE和重新尝试指示器IE（如果有）。UE应按照3GPP TS 24.526[19]中的规定评估URSP规则（如果可用），并且UE可以在评估这些URSP规则后发送PDU会话建立请求。

Upon receipt of an indication from 5GMM sublayer that the 5GSM message was not forwarded because the DNN is not supported or not subscribed in a slice along with a PDU SESSION ESTABLISHMENT REQUEST message with the PDU session ID IE set to the PDU session ID of the PDU session, the UE shall stop timer T3580, shall abort the procedure and shall behave as follows:
当从5GMM子层接收到5GMM消息未转发的指示时，由于DNN不受支持或未在切片中订阅，以及PDU会话建立请求消息，PDU会话ID IE设置为PDU会话的PDU会话标识，UE应停止计时器T3580，中止该过程，并应表现如下：

a)    if the timer value indicates neither zero nor deactivated, the UE shall start the back-off timer with the value received from the 5GMM sublayer for the PDU session establishment procedure and the [PLMN, DNN, S-NSSAI] combination or the [PLMN, DNN, no S-NSSAI] combination, if no S-NSSAI was provided during the PDU session establishment. The UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message in the PLMN for the same DNN and the same S-NSSAI that were sent by the UE, or for the same DNN and no S-NSSAI if S-NSSAI that was not sent by the UE, until:

a） 如果计时器值指示既不为零也不停用，则UE应使用从5GMM子层接收到的值启动退避计时器，用于PDU会话建立过程和[PLMN，DNN，S-NSSAI]组合，或者如果在PDU会话创建过程中未提供S-NSSA，则启动[PLMN，DNN，no S-NSSAI]组合。对于UE发送的同一DNN和同一S-NSSAI，或者对于相同DNN和无S-NSSAI，如果S-NSSAI不是由UE发送，则UE不得在PLMN中发送另一个PDU会话建立请求消息，直到：

1)    the back-off timer expires;
1） 退避计时器过期；
2)    the UE is switched off;
2） UE关闭；
3)    the USIM is removed the entry in the "list of subscriber data" for the current SNPN is updated if the UE does not support access to an SNPN using credentials from a credentials holder, or the selected entry of the "list of subscriber data" is updated if the UE supports access to an SNPN using credentials from a credentials holder; or
3） USIM被删除。如果UE不支持使用来自凭证持有人的凭证访问SNPN，则更新当前SNPN的“订户数据列表”中的条目，或者如果UE支持使用来自凭据持有人的凭证来访问SNPN，“订户数据表列”的所选条目被更新；或
4)    the DNN is included in the LADN information and the network provides the LADN information during the registration procedure or the generic UE configuration update procedure;
4） DNN包括在LADN信息中，并且网络在注册过程或通用UE配置更新过程期间提供LADN信息；

b)    if the timer value is not received from the 5GMM sublayer or the timer value indicates that this timer is deactivated, the UE shall not send another PDU SESSION ESTABLISHMENT REQUEST message in the PLMN for the same DNN and the same S-NSSAI that were sent by the UE, or for the same DNN and no S-NSSAI if S-NSSAI that was not sent by the UE, until:
b） 如果未从5GMM子层接收到计时器值或计时器值指示该计时器已停用，则UE不得在PLMN中为UE发送的相同DNN和相同S-NSSAI发送另一个PDU会话建立请求消息，或为相同DNN发送另一条PDU会话建立请求消息，如果S-NSSA不是由UE发送，则不发送S-NSSAI，直到：

1)    the UE is switched off;
1） UE关闭；
2)    the USIM is removed, the entry in the "list of subscriber data" for the current SNPN is updated if the UE does not support access to an SNPN using credentials from a credentials holder, or the selected entry of the "list of subscriber data" is updated if the UE supports access to an SNPN using credentials from a credentials holder; or
2） 移除USIM，如果UE不支持使用来自凭证持有人的凭证访问SNPN，则更新当前SNPN的“订户数据列表”中的条目，或者如果UE支持使用来自凭据持有人的凭据访问SNPN，“订户数据表”的所选条目被更新；或
3)    the DNN is included in the LADN information and the network provides the LADN information during the registration procedure or the generic UE configuration update procedure; and
3） DNN包括在LADN信息中，并且网络在注册过程或通用UE配置更新过程期间提供LADN信息；和

c)    if the timer value indicates zero, the UE may send another PDU SESSION ESTABLISHMENT REQUEST message for the same combination of [PLMN, DNN, S-NSSAI], [PLMN, DNN, no S-NSSAI] in the current PLMN.
c） 如果计时器值指示零，则UE可以针对当前PLMN中的[PLMN，DNN，S-NSSAI]、[PLMN、DNN，no S-nssa]的相同组合发送另一PDU会话建立请求消息。