STM32F103C8T6 USART2 配置

void uart_init( u32 bound )
{
	/* GPIO端口设置 */
	GPIO_InitTypeDef	GPIO_InitStructure;
	USART_InitTypeDef	USART_InitStructure;
	NVIC_InitTypeDef	NVIC_InitStructure;

	RCC_APB2PeriphClockCmd(  RCC_APB2Periph_GPIOA, ENABLE ); 
	RCC_APB1PeriphClockCmd( RCC_APB1Periph_USART2, ENABLE );         /* 使能USART1，GPIOA时钟 */

	/* PA2 TXD2 */
	GPIO_InitStructure.GPIO_Pin	= GPIO_Pin_2;
	GPIO_InitStructure.GPIO_Speed	= GPIO_Speed_50MHz;
	GPIO_InitStructure.GPIO_Mode	= GPIO_Mode_AF_PP;
	GPIO_Init( GPIOA, &GPIO_InitStructure );

	/* PA3 RXD2 */
	GPIO_InitStructure.GPIO_Pin	= GPIO_Pin_3;
	GPIO_InitStructure.GPIO_Mode	= GPIO_Mode_IN_FLOATING;
	GPIO_Init( GPIOA, &GPIO_InitStructure );

	/* Usart1 NVIC 配置 */
	NVIC_InitStructure.NVIC_IRQChannel			= USART2_IRQn;
	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority	= 3;                            /* 抢占优先级3 */
	NVIC_InitStructure.NVIC_IRQChannelSubPriority		= 2;                            /* 子优先级3 */
	NVIC_InitStructure.NVIC_IRQChannelCmd			= ENABLE;                       /* IRQ通道使能 */
	NVIC_Init( &NVIC_InitStructure );                                                       /* 根据指定的参数初始化VIC寄存器 */

	/* USART 初始化设置 */
	USART_InitStructure.USART_BaudRate		= bound;                                /* 串口波特率 */
	USART_InitStructure.USART_WordLength		= USART_WordLength_8b;                  /* 字长为8位数据格式 */
	USART_InitStructure.USART_StopBits		= USART_StopBits_1;                     /* 一个停止位 */
	USART_InitStructure.USART_Parity		= USART_Parity_No;                      /* 无奇偶校验位 */
	USART_InitStructure.USART_HardwareFlowControl	= USART_HardwareFlowControl_None;       /* 无硬件数据流控制 */
	USART_InitStructure.USART_Mode			= USART_Mode_Rx | USART_Mode_Tx;        /* 收发模式 */

	USART_Init( USART2, &USART_InitStructure );                                             /* 初始化串口1 */
	USART_ITConfig( USART2, USART_IT_RXNE, ENABLE );                                        /* 开启串口接受中断 */
	USART_Cmd( USART2, ENABLE );                                                            /* 使能串口 2 */
}

void USART2_IRQHandler( void )                                          
{
	if ( USART_GetITStatus( USART2, USART_IT_RXNE ) != RESET )     
	{
		res = USART_ReceiveData( USART2 );                      
		USART_SendData(USART2,res);
	}
}