I2C之24c02

#include<reg51.h>
#include <INTRINS.H>

bit write=0;
sbit SDA=P2^0;
sbit SCL=P2^1;
sbit wela=P2^7;
sbit dula=P2^6;
sbit beep=P2^3;

//sbit RST=P2^5;   //时钟  不需要，可以关掉

/**** 注意：以下这句不可关掉，否则断电后数据不会保存****/
sbit CS_DA =P2^4 ;  //HJ-3G DAC HL-1不需要，可以关掉

unsigned char num;
unsigned char a,b,sec,count;
unsigned char code table[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,
                        0x07,0x7f,0x6f,0x77,0x7c,0x39,0x5e,0x79,0x71};

void Delay(unsigned char i)
{
unsigned char j,k;
for(j=i;j>0;j--)
for(k=110;k>0;k--);
}

/*
void Diaplay(unsigned char a,unsigned char b)
{
wela=1;
P0=0x7d;
wela=0;
Delay(5);

dula=1;
P0=table[a];  //显示百位
dula=0;

wela=1;
P0=0x7e;
wela=0;
Delay(5);

dula=1;
P0=table[b]; //显示十位
dula=0;
}

*/
/****与上面的比较有什么不同，上面的会点亮别的数码管****/
void Diaplay(unsigned char a,unsigned char b)
{
dula=0;
P0=table[a];  //显示百位
dula=1;
dula=0;

wela=0;
P0=0x7e;
wela=1;
wela=0;
Delay(5);

dula=0;
P0=table[b]; //显示十位
dula=1;
dula=0;

wela=0;
P0=0x7d;
wela=1;
wela=0;
Delay(5);
}

void nop()
{
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
_nop_();
}

void init()
{
// RST=0; //总线时钟低电评
  CS_DA =0 ; //若无此语句，则不会读出保存值
SCL=1;
nop();
SDA=1;
nop();
}

//开始信号
void Start_i2c()
{
SDA=1;
nop();
SCL=1;
nop();
SDA=0;
nop();
//SCL=0;
//nop();
}
//停止信号

void Stop_i2c()
{
SDA=0;
nop();
SCL=1;
nop();
SDA=1;
nop();
}

void Respons()
{
unsigned char i;
SCL=1;
nop();
while((SDA==1)&&(i<250)) i++;
SCL=0;
nop();
}

//发送一个字节
void Write_Byte(unsigned char j)
{
unsigned char i,temp;
temp=j;
for(i=0;i<8;i++)
{
temp=temp<<1;
SCL=0;
nop();
SDA=CY;
nop();
SCL=1;  //待sda线上的数据稳定后，将scl拉高
nop();
   }
SCL=0;
nop();
SDA=1;
nop();
}

unsigned char Read_Byte() //为什么不是void的形式
{
unsigned char i,k;
k=0;
SCL=0;
nop();
SDA=1; //??置数据线为输入方式
nop();
for(i=0;i<8;i++)
{
SCL=1;
nop();
k=(k<<1)|SDA;
SCL=0;
nop();
   }
nop();
return(k);
}

void Write_add(unsigned char address,unsigned char dat)
{
Start_i2c();
Write_Byte(0xa0);
Respons();
Write_Byte(address);
Respons();
Write_Byte(dat);
Respons();
Stop_i2c();
}

unsigned char Read_add(unsigned char address)
{
unsigned char dat;
Start_i2c();
Write_Byte(0xa0);
Respons();
Write_Byte(address);
Respons();
Start_i2c();
Write_Byte(0xa1);
Respons();
dat=Read_Byte();
Stop_i2c();
return dat;
}

void Time0_init()
{
TMOD=0x01;
TH0=(65536-50000)/256;
TL0=(65536-50000)%256;

ET0=1;
EA=1;
TR0=1;
}

void main()
{
init();
sec=Read_add(3);
Time0_init();
Delay(100);
while(1)
{
a=sec/10;
 b=sec%10;
Diaplay(a,b);
if(write==1)
{
write=0;
Write_add(3,sec);
beep=0;
Delay(50);
beep=1;
//Delay(200);
     }
  }
}

void time0() interrupt 1
{
TH0=(65536-50000)/256;
TL0=(65536-50000)%256;
  count++;
if(count==18)
{
count=0;
sec++;
write=1;
if(sec==100)
sec=0;
    }
}