目 录
摘 要………………………………………………………………………………Ⅰ
Abstract…………………………………………………………………………Ⅱ
1 绪论…………………………………………………………………………………1
1.1 本课题的目的和意义…………………………………………………………1
1.2 净油机工作原理及分析……………………………………………………1
1.3净油机发展现状……………………………………………………………2
1.4GRJ-50高效净油机简介……………………………………………………3
2 真空净油机的工作原理简介………………………………………………………4
2.1真空净油机净油原理概述……………………………………………………4
2.2真空净油机工艺流程概述……………………………………………………4
3 总体方案设计………………………………………………………………………6
3.1真空净油机草图方案…………………………………………………………6
3.2真空净油机设计要求…………………………………………………………6
3.3真空罐草图设计说明…………………………………………………………7
3.4油泵方案选择…………………………………………………………………9
3.5真空泵选择方案 ……………………………………………………………10
3.6风冷器选择方案 ……………………………………………………………11
3.7缓冲器设计说明 ……………………………………………………………12
3.8凝水器设计说明 ……………………………………………………………12
3.9氮气发生器选择方案 ………………………………………………………13
3.10电控柜设计说明……………………………………………………………13
4 过滤加热装置的设计 ……………………………………………………………15
4.1进油过滤器设计说明 ………………………………………………………15
4.2精滤器设计说明 ……………………………………………………………15
4.3加热器设计说明 ……………………………………………………………16
4.4真空罐最终设计说明 ………………………………………………………17
5 净油机机架设计 …………………………………………………………………20
6 管路设计 …………………………………………………………………………21
7 法兰盘设计 ………………………………………………………………………23
8 阀门设计 …………………………………………………………………………24
9 净油机三维装配设计 ……………………………………………………………25
10 净油机工程图设计………………………………………………………………29
11结论 ………………………………………………………………………………30
致谢 …………………………………………………………………………………31
参考文献 ……………………………………………………………………………32
摘 要
凡是有机器运转的地方,都能看到润滑油的身影。这是由于在机器里加入润滑油可以起到润滑、冷却、防锈、清洁、密封、缓冲、散热等作用。然而,在使用过程中,由于种种原因导致润滑油混入各种杂质,使油液失效,导致机器故障,造成经济损失。
故尔,润滑油必须经过净化处理才能使用。本文针对润滑油中混入的水分进行提纯,在现有真空净油机的基础上,设计一款真空净油机,将完成总体方案设计、过滤加热装置设计、三模建模以及绘制工程图等工作。
关键词:真空净油机 设计 三维
Abstract
Where the place of the machinery, you can see the figure of lubricating oil. This is because the machine can add lubricating oil in the lubricating, cooling, antirust, clean, seal, buffer, heat dissipation, etc. In use process, however, for various reasons result in lubricating oil mixed with a variety of impurities, disable oil, lead to malfunction and cause economic losses.
Therefore, should only be used lubricating oil must undergo purification treatment. Lubricating oil mixed with water in the purification, the author of this paper, on the basis of the existing vacuum oil purifier, design a vacuum oil purifier, will complete the overall scheme design, filtering, heating equipment design, Three-dimensionaland drawing engineering drawings, etc.
Key words: Vacuum oil purifierDesignThree-dimensional
………………