GE IC687RCM711是一个冗余通信模块,为从活动单元到备用单元的同步消息提供路径。然后将其用作在FIP单机架冗余系统中同步双CPU的方法。这还允许在两个单元之间传输共享I/O数据的路径。FIP单机架冗余系统各单元之间的实际物理连接可包括多达三英尺的总互连电缆。兼容的CPU包括IC697CFR782和IC697CFR28。
GE IC687BEM744是一款FIP总线控制器,专门为GE Fanuc生产的IC697系列PLC设计。它是四个兼容FIP总线控制器之一,是一个半插槽模块。由于模块的结构具有半角面板,因此非常适合安装在集成机架中。半槽模块在功能上与全槽FBC相同。IC687BEM744应与2.5MHz WorldFIP网络一起使用。与其他四个FIP总线控制器一样,IC687BEM744除了支持一般的消息兼容性和支持外,还支持TCP/IP通信。请注意,FIP总线控制器(如IC687BEM744)不能安装在90-70 PLC系统的PLC扩展机架中。然而,一个90-70 PLC系统最多可支持四个FIP总线控制器。IC687BEM744配备6个指示状态的LED、一个15针串行连接器RS-485端口、两个9针FIP现场总线连接器通道和一个重启按钮。6个LED从上到下表示以下内容:模块正常、总线仲裁器、载波检测通道1、传输启用通道1、载波检测通道2和传输启用通道2。RS-485端口用于轻松将电脑连接到模块,以升级固件。重启按钮允许用户重启模块或重新加载软件,同时重启模块。两个FIP总线连接器允许IC687BEM744支持冗余总线功能。系统通电时,切勿安装或卸下模块,这一点很重要。
GE Fanuc IC687BEM744 is a FIP bus controller, specially designed for the IC967 series PLC manufactured by GE Fanuc. It is one of four compatible FIP bus controllers and is a half-slot module. Because the module’s architecture has half-angle panels, it is very suitable for installation in an integrated rack. The half-slot module is functionally the same as the full-slot FBC. IC687BEM744 should be used with 2.5MHz WorldFIP network. Like the other four FIP bus controllers, IC687BEM744 supports TCP/IP communication in addition to general messaging compatibility and support. Please note that the FIP bus controller (such as IC687BEM744) cannot be installed in the PLC extension rack of the 90-70 PLC system. However, a single 90-70 PLC system can support up to four FIP bus controllers.
The IC687BEM744 is equipped with 6 LED’s to indicate status, a 15-pin serial connector RS-485 port, two 9-pin FIP Fieldbus connector channels, and a restart button. The 6 LED’s represent the following, from top to bottom: Module OK, Bus Arbiter, Carrier Detect Ch. 1, Transmit Enable Ch. 1, Carrier Detect Ch. 2, and Transmit Enable Ch. 2. The RS-485 port is used to easily connect your PC to the module for upgrading firmware. The restart button allows the user to restart the module or to reload software while simultaneously restarting the module. The two FIP Bus Connectors allows the IC687BEM744 to support redundant bus capabilities. It is important to never install or remove the module when power is applied to the system.
IC670MDL640J
IC670MDL642J
IC670MDL730
IC670MDL740
IC670MDL740K
IC670MDL930
IC670MDL930K
IC670MFP100
IC670PBI00
IC670PBI001
IC676PBM442
IC687BEM713
IC687BEM713C
IC687BEM731
IC687BEM744
IC687BEM744-EB
IC687RCM711
IC690ACC900
IC690ACC901
IC690CRG001
IC690PRM120
IC690PRS020
IC690USB901
IC693ACC300
IC693ACC301
IC693ACC302