[全志T113]：ST7701 86屏幕驱动
添加屏幕驱动流程
1.添加驱动源码
如果要添加lcd驱动，添加位置如下：
/home/ubuntu/Tina-Linux/lichee/linux-5.4/drivers/video/fbdev/sunxi/disp2
2.配置kconfig和Makefile
同时配置目录下的Kconfig与Makefile，文件路径分别如下：
/home/ubuntu/Tina-Linux/lichee/linux-5.4/drivers/video/fbdev/sunxi/disp2/disp/lcd/Kconfig
/home/ubuntu/Tina-Linux/lichee/linux-5.4/drivers/video/fbdev/sunxi/disp2/disp/Makefile
2.1 kconfig
config LCD_SUPPORT_ST7701_86
bool "LCD support ST7701_86 panel"
default y
---help---
If you want to support ST7701_86 panel for display driver, select it.
2.2 Makefile
disp-$(CONFIG_LCD_SUPPORT_ST7701_86) += lcd/st7701_86.o
2.3 built-in.a
这个文件需要添加我们刚才编译完的.o文件
lcd/st7701_86.o/
3.修改panels.c和panels.h
/home/ubuntu/Tina-Linux/lichee/linux-5.4/drivers/video/fbdev/sunxi/disp2/disp/lcd/panels.c
/home/ubuntu/Tina-Linux/lichee/linux-5.4/drivers/video/fbdev/sunxi/disp2/disp/lcd/panels.h
#ifdef CONFIG_LCD_SUPPORT_ST7701_86
extern struct __lcd_panel st7701_86_panel;
#endif
4.修改dts
&lcd0 {
/* part 1 */
lcd_used = <1>;
lcd_driver_name = "st7701_86";
lcd_backlight = <255>;
/* part 2 */
lcd_if = <0>;
lcd_hv_if = <0>;
/* part 3 */
lcd_x = <480>;
lcd_y = <480>;
lcd_width = <71>;
lcd_height = <71>;
lcd_dclk_freq = <16>;
lcd_hbp = <20>;
lcd_ht = <526>;
lcd_hspw = <6>;
lcd_vbp = <10>;
lcd_vt = <510>;
lcd_vspw = <4>;
lcd_pwm_used = <1>;
lcd_pwm_ch = <7>;
lcd_pwm_freq = <5000>;
lcd_pwm_pol = <0>;
/* part 5 */
lcd_frm = <1>;
lcd_io_phase = <0x0000>;
lcd_gamma_en = <0>;
lcd_cmap_en = <0>;
lcd_hv_clk_phase = <0>;
lcd_hv_sync_polarity= <0>;
// reset
lcd_gpio_0 = <&pio PB 4 GPIO_ACTIVE_HIGH>;
// cs
lcd_gpio_1 = <&pio PB 7 GPIO_ACTIVE_HIGH>;
// sda
lcd_gpio_2 = <&pio PB 5 GPIO_ACTIVE_HIGH>;
// sck
lcd_gpio_3 = <&pio PB 6 GPIO_ACTIVE_HIGH>;
//bl
lcd_bl_en = <&pio PD 22 GPIO_ACTIVE_HIGH>;
/* part 6 */
lcd_power = "vcc-lcd";
lcd_pin_power = "vcc-pd";
pinctrl-0 = <&rgb18_pins_a>;
pinctrl-1 = <&rgb18_pins_b>;
};
&disp {
disp_init_enable = <1>;
disp_mode = <0>;
screen0_output_type = <1>;
screen0_output_mode = <4>;
screen1_output_type = <3>;
screen1_output_mode = <10>;
screen1_output_format = <0>;
screen1_output_bits = <0>;
screen1_output_eotf = <4>;
screen1_output_cs = <257>;
screen1_output_dvi_hdmi = <2>;
screen1_output_range = <2>;
screen1_output_scan = <0>;
screen1_output_aspect_ratio = <8>;
dev0_output_type = <1>;
dev0_output_mode = <4>;
dev0_screen_id = <0>;
dev0_do_hpd = <0>;
dev1_output_type = <4>;
dev1_output_mode = <10>;
dev1_screen_id = <1>;
dev1_do_hpd = <1>;
def_output_dev = <0>;
hdmi_mode_check = <1>;
fb0_format = <0>;
fb0_width = <0>;
fb0_height = <0>;
fb1_format = <0>;
fb1_width = <0>;
fb1_height = <0>;
chn_cfg_mode = <1>;
disp_para_zone = <1>;
/*VCC-LCD*/
/* dc1sw-supply = <®_pio3_3>;*/
/*VCC-DSI*/
/* eldo3-supply = <®_eldo3>;*/
/*VCC-PD*/
/* dcdc1-supply = <®_pio3_3>;*/
};
5.测试
root@TinaLinux:/# cat /dev/urandom > /dev/fb0
root@TinaLinux:/# echo 8 > /sys/class/disp/disp/attr/colorbar
6.驱动文件
驱动文件参考繁花cloud提供的sdk
st7701_86.c
/*
* drivers/video/fbdev/sunxi/disp2/disp/lcd/st7701_86/st7701_86.c
*
* Copyright (c) 2007-2018 Allwinnertech Co., Ltd.
* Author: zhengxiaobin <zhengxiaobin@allwinnertech.com>
*
* This software is licensed under the terms of the GNU General Public
* License version 2, as published by the Free Software Foundation, and
* may be copied, distributed, and modified under those terms.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
[lcd0]
lcd_used = 1
lcd_driver_name = "st7701_86"
lcd_x = 480
lcd_y = 480
lcd_width = 71
lcd_height = 71
lcd_dclk_freq = 30
lcd_pwm_used = 1
lcd_pwm_ch = 8
lcd_pwm_freq = 50000
lcd_pwm_pol = 0
lcd_pwm_max_limit = 255
lcd_hbp = 120
;10 + 20 + 10 + 240*3 = 760 real set 1000
lcd_ht = 850
lcd_hspw = 2
lcd_vbp = 13
lcd_vt = 373
lcd_vspw = 2
lcd_frm = 1
lcd_if = 0
lcd_hv_if = 8
lcd_hv_clk_phase = 0
lcd_hv_sync_polarity = 0
lcd_hv_srgb_seq = 0
lcd_io_phase = 0x0000
lcd_gamma_en = 0
lcd_bright_curve_en = 1
lcd_cmap_en = 0
lcd_rb_swap = 0
deu_mode = 0
lcdgamma4iep = 22
smart_color = 90
;lcd_bl_en = port:PB03<1><0><default><1>
lcd_power = "vcc-lcd"
lcd_pin_power = "vcc-pd"
;reset
lcd_gpio_0 = port:PD09<1><0><default><1>
;cs
lcd_gpio_1 = port:PD10<1><0><default><0>
;sda
lcd_gpio_2 = port:PD13<1><0><default><0>
;sck
lcd_gpio_3 = port:PD12<1><0><default><0>
lcdd5 = port:PD03<2><0><2><default>
lcdd6 = port:PD04<2><0><2><default>
lcdd7 = port:PD05<2><0><2><default>
lcdd10 = port:PD06<2><0><2><default>
lcdd11 = port:PD07<2><0><2><default>
lcdd12 = port:PD08<2><0><2><default>
lcdclk = port:PD18<2><0><3><default>
lcdde = port:PD19<2><0><3><default>
lcdhsync = port:PD20<2><0><3><default>
lcdvsync = port:PD21<2><0><3><default>
[lcd0_suspend]
lcdd5 = port:PD03<7><0><2><default>
lcdd6 = port:PD04<7><0><2><default>
lcdd7 = port:PD05<7><0><2><default>
lcdd10 = port:PD06<7><0><2><default>
lcdd11 = port:PD07<7><0><2><default>
lcdd12 = port:PD08<7><0><2><default>
lcdclk = port:PD18<7><0><3><default>
lcdde = port:PD19<7><0><3><default>
lcdhsync = port:PD20<7><0><3><default>
lcdvsync = port:PD21<7><0><3><default>
*/
#include "st7701_86.h"
#define spi_scl_1 sunxi_lcd_gpio_set_value(0, 3, 1)
#define spi_scl_0 sunxi_lcd_gpio_set_value(0, 3, 0)
#define spi_sdi_1 sunxi_lcd_gpio_set_value(0, 2, 1)
#define spi_sdi_0 sunxi_lcd_gpio_set_value(0, 2, 0)
#define spi_cs_1 sunxi_lcd_gpio_set_value(0, 1, 1)
#define spi_cs_0 sunxi_lcd_gpio_set_value(0, 1, 0)
static void lcd_panel_st7701_86_init(void);
static void LCD_power_on(u32 sel);
static void LCD_power_off(u32 sel);
static void LCD_bl_open(u32 sel);
static void LCD_bl_close(u32 sel);
static void LCD_panel_init(u32 sel);
static void LCD_panel_exit(u32 sel);
static void LCD_cfg_panel_info(struct panel_extend_para *info)
{
u32 i = 0, j = 0;
u32 items;
u8 lcd_gamma_tbl[][2] = {
/* {input value, corrected value} */
{0, 0}, {15, 15}, {30, 30}, {45, 45}, {60, 60},
{75, 75}, {90, 90}, {105, 105}, {120, 120}, {135, 135},
{150, 150}, {165, 165}, {180, 180}, {195, 195}, {210, 210},
{225, 225}, {240, 240}, {255, 255},
};
u32 lcd_cmap_tbl[2][3][4] = {
{
{LCD_CMAP_G0, LCD_CMAP_B1, LCD_CMAP_G2, LCD_CMAP_B3},
{LCD_CMAP_B0, LCD_CMAP_R1, LCD_CMAP_B2, LCD_CMAP_R3},
{LCD_CMAP_R0, LCD_CMAP_G1, LCD_CMAP_R2, LCD_CMAP_G3},
},
{
{LCD_CMAP_B3, LCD_CMAP_G2, LCD_CMAP_B1, LCD_CMAP_G0},
{LCD_CMAP_R3, LCD_CMAP_B2, LCD_CMAP_R1, LCD_CMAP_B0},
{LCD_CMAP_G3, LCD_CMAP_R2, LCD_CMAP_G1, LCD_CMAP_R0},
},
};
items = sizeof(lcd_gamma_tbl) / 2;
for (i = 0; i < items - 1; i++) {
u32 num = lcd_gamma_tbl[i + 1][0] - lcd_gamma_tbl[i][0];
for (j = 0; j < num; j++) {
u32 value = 0;
value =
lcd_gamma_tbl[i][1] +
((lcd_gamma_tbl[i + 1][1] - lcd_gamma_tbl[i][1]) *
j) /
num;
info->lcd_gamma_tbl[lcd_gamma_tbl[i][0] + j] =
(value << 16) + (value << 8) + value;
}
}
info->lcd_gamma_tbl[255] = (lcd_gamma_tbl[items - 1][1] << 16) +
(lcd_gamma_tbl[items - 1][1] << 8) +
lcd_gamma_tbl[items - 1][1];
memcpy(info->lcd_cmap_tbl, lcd_cmap_tbl, sizeof(lcd_cmap_tbl));
}
static s32 LCD_open_flow(u32 sel)
{
/* open lcd power, and delay 50ms */
LCD_OPEN_FUNC(sel, LCD_power_on, 200);
/* open lcd power, than delay 200ms */
LCD_OPEN_FUNC(sel, LCD_panel_init, 200);
/* open lcd controller, and delay 100ms */
LCD_OPEN_FUNC(sel, sunxi_lcd_tcon_enable, 150);
/* open lcd backlight, and delay 0ms */
LCD_OPEN_FUNC(sel, LCD_bl_open, 0);
return 0;
}
static s32 LCD_close_flow(u32 sel)
{
/* close lcd backlight, and delay 0ms */
LCD_CLOSE_FUNC(sel, LCD_bl_close, 50);
/* close lcd controller, and delay 0ms */
LCD_CLOSE_FUNC(sel, sunxi_lcd_tcon_disable, 10);
/* open lcd power, than delay 200ms */
LCD_CLOSE_FUNC(sel, LCD_panel_exit, 10);
/* close lcd power, and delay 500ms */
LCD_CLOSE_FUNC(sel, LCD_power_off, 10);
return 0;
}
static void LCD_power_on(u32 sel)
{
/* config lcd_power pin to open lcd power0 */
sunxi_lcd_power_enable(sel, 0);
/* pwr_en, active low */
sunxi_lcd_gpio_set_value(sel, 3, 0);
sunxi_lcd_pin_cfg(sel, 1);
}
static void LCD_power_off(u32 sel)
{
sunxi_lcd_pin_cfg(sel, 0);
/* pwr_en, active low */
sunxi_lcd_gpio_set_value(sel, 3, 1);
/* config lcd_power pin to close lcd power0 */
sunxi_lcd_power_disable(sel, 0);
}
static void LCD_bl_open(u32 sel)
{
sunxi_lcd_pwm_enable(sel);
/* config lcd_bl_en pin to open lcd backlight */
sunxi_lcd_backlight_enable(sel);
}
static void LCD_bl_close(u32 sel)
{
/* config lcd_bl_en pin to close lcd backlight */
sunxi_lcd_backlight_disable(sel);
sunxi_lcd_pwm_disable(sel);
}
static void st7701_86_spi_write_cmd(u8 value)
{
int i;
spi_cs_0;
spi_sdi_0;
spi_scl_0;
sunxi_lcd_delay_us(10);
spi_scl_1;
for (i = 0; i < 8; i++) {
sunxi_lcd_delay_us(10);
if (value & 0x80)
spi_sdi_1;
else
spi_sdi_0;
spi_scl_0;
sunxi_lcd_delay_us(10);
spi_scl_1;
value <<= 1;
}
sunxi_lcd_delay_us(10);
spi_cs_1;
}
static void st7701_86_spi_write_data(u8 value)
{
int i;
spi_cs_0;
spi_sdi_1;
spi_scl_0;
sunxi_lcd_delay_us(10);
spi_scl_1;
for (i = 0; i < 8; i++) {
sunxi_lcd_delay_us(10);
if (value & 0x80)
spi_sdi_1;
else
spi_sdi_0;
value <<= 1;
sunxi_lcd_delay_us(10);
spi_scl_0;
spi_scl_1;
}
sunxi_lcd_delay_us(10);
spi_cs_1;
}
static void LCD_panel_init(u32 sel)
{
struct disp_panel_para *info =
kmalloc(sizeof(struct disp_panel_para), GFP_KERNEL | __GFP_ZERO);
bsp_disp_get_panel_info(sel, info);
lcd_panel_st7701_86_init();
kfree(info);
return;
}
static void LCD_panel_exit(u32 sel)
{
struct disp_panel_para *info =
kmalloc(sizeof(struct disp_panel_para), GFP_KERNEL | __GFP_ZERO);
st7701_86_spi_write_cmd(0x28);
st7701_86_spi_write_cmd(0x10);
sunxi_lcd_delay_ms(300);
bsp_disp_get_panel_info(sel, info);
kfree(info);
return;
}
static void lcd_panel_st7701_86_init(void)
{
/* VCI=3.3V */
/************* Reset LCD Driver ****************/
spi_cs_0;
sunxi_lcd_gpio_set_value(0, 0, 1);
sunxi_lcd_delay_ms(50);
sunxi_lcd_gpio_set_value(0, 0, 0);
/* Delay 10ms, This delay time is necessary */
sunxi_lcd_delay_ms(100);
sunxi_lcd_gpio_set_value(0, 0, 1);
/* Delay 120 ms */
sunxi_lcd_delay_ms(150);
/******************************************************************************/
st7701_86_spi_write_cmd(0xFF);
st7701_86_spi_write_data(0x77);
st7701_86_spi_write_data(0x01);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x13);
st7701_86_spi_write_cmd(0xEF);
st7701_86_spi_write_data(0x08);
st7701_86_spi_write_cmd(0xFF);
st7701_86_spi_write_data(0x77);
st7701_86_spi_write_data(0x01);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x10);
st7701_86_spi_write_cmd(0xC0);
st7701_86_spi_write_data(0x3B);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_cmd(0xC1);
st7701_86_spi_write_data(0x0D);
st7701_86_spi_write_data(0x02);
st7701_86_spi_write_cmd(0xC2);
st7701_86_spi_write_data(0x21);
st7701_86_spi_write_data(0x08);
st7701_86_spi_write_cmd(
0xC3); //配置工作模式为DE模式，供应商给的驱动源码并没有设置该 地址 。
st7701_86_spi_write_data(
0x02); // 0X02 The data is input on the negative edge of DOTCLK
st7701_86_spi_write_data(0x02);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_cmd(0xCD);
st7701_86_spi_write_data(
0x08); //18-bit/pixel: MDT=0:D[21:16]=R,D[13:8]=G,D[5:0]=B(CDH=00) ;
// MDT=1:D[17:12]=R,D[11:6]=G,D[5:0]=B(CDH=08) ;
st7701_86_spi_write_cmd(0xB0);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x11);
st7701_86_spi_write_data(0x18);
st7701_86_spi_write_data(0x0E);
st7701_86_spi_write_data(0x11);
st7701_86_spi_write_data(0x06);
st7701_86_spi_write_data(0x07);
st7701_86_spi_write_data(0x08);
st7701_86_spi_write_data(0x07);
st7701_86_spi_write_data(0x22);
st7701_86_spi_write_data(0x04);
st7701_86_spi_write_data(0x12);
st7701_86_spi_write_data(0x0F);
st7701_86_spi_write_data(0xAA);
st7701_86_spi_write_data(0x31);
st7701_86_spi_write_data(0x18);
st7701_86_spi_write_cmd(0xB1);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x11);
st7701_86_spi_write_data(0x19);
st7701_86_spi_write_data(0x0E);
st7701_86_spi_write_data(0x12);
st7701_86_spi_write_data(0x07);
st7701_86_spi_write_data(0x08);
st7701_86_spi_write_data(0x08);
st7701_86_spi_write_data(0x08);
st7701_86_spi_write_data(0x22);
st7701_86_spi_write_data(0x04);
st7701_86_spi_write_data(0x11);
st7701_86_spi_write_data(0x11);
st7701_86_spi_write_data(0xA9);
st7701_86_spi_write_data(0x32);
st7701_86_spi_write_data(0x18);
st7701_86_spi_write_cmd(0xFF);
st7701_86_spi_write_data(0x77);
st7701_86_spi_write_data(0x01);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x11);
st7701_86_spi_write_cmd(0xB0);
st7701_86_spi_write_data(0x60);
st7701_86_spi_write_cmd(0xB1);
st7701_86_spi_write_data(0x30);
st7701_86_spi_write_cmd(0xB2);
st7701_86_spi_write_data(0x87);
st7701_86_spi_write_cmd(0xB3);
st7701_86_spi_write_data(0x80);
st7701_86_spi_write_cmd(0xB5);
st7701_86_spi_write_data(0x49);
st7701_86_spi_write_cmd(0xB7);
st7701_86_spi_write_data(0x85);
st7701_86_spi_write_cmd(0xB8);
st7701_86_spi_write_data(0x21);
st7701_86_spi_write_cmd(0xC1);
st7701_86_spi_write_data(0x78);
st7701_86_spi_write_cmd(0xC2);
st7701_86_spi_write_data(0x78);
sunxi_lcd_delay_ms(20);
st7701_86_spi_write_cmd(0xE0);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x1B);
st7701_86_spi_write_data(0x02);
st7701_86_spi_write_cmd(0xE1);
st7701_86_spi_write_data(0x08);
st7701_86_spi_write_data(0xA0);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x07);
st7701_86_spi_write_data(0xA0);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x44);
st7701_86_spi_write_data(0x44);
st7701_86_spi_write_cmd(0xE2);
st7701_86_spi_write_data(0x11);
st7701_86_spi_write_data(0x11);
st7701_86_spi_write_data(0x44);
st7701_86_spi_write_data(0x44);
st7701_86_spi_write_data(0xED);
st7701_86_spi_write_data(0xA0);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0xEC);
st7701_86_spi_write_data(0xA0);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_cmd(0xE3);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x11);
st7701_86_spi_write_data(0x11);
st7701_86_spi_write_cmd(0xE4);
st7701_86_spi_write_data(0x44);
st7701_86_spi_write_data(0x44);
st7701_86_spi_write_cmd(0xE5);
st7701_86_spi_write_data(0x0A);
st7701_86_spi_write_data(0xE9);
st7701_86_spi_write_data(0xD8);
st7701_86_spi_write_data(0xA0);
st7701_86_spi_write_data(0x0C);
st7701_86_spi_write_data(0xEB);
st7701_86_spi_write_data(0xD8);
st7701_86_spi_write_data(0xA0);
st7701_86_spi_write_data(0x0E);
st7701_86_spi_write_data(0xED);
st7701_86_spi_write_data(0xD8);
st7701_86_spi_write_data(0xA0);
st7701_86_spi_write_data(0x10);
st7701_86_spi_write_data(0xEF);
st7701_86_spi_write_data(0xD8);
st7701_86_spi_write_data(0xA0);
st7701_86_spi_write_cmd(0xE6);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x11);
st7701_86_spi_write_data(0x11);
st7701_86_spi_write_cmd(0xE7);
st7701_86_spi_write_data(0x44);
st7701_86_spi_write_data(0x44);
st7701_86_spi_write_cmd(0xE8);
st7701_86_spi_write_data(0x09);
st7701_86_spi_write_data(0xE8);
st7701_86_spi_write_data(0xD8);
st7701_86_spi_write_data(0xA0);
st7701_86_spi_write_data(0x0B);
st7701_86_spi_write_data(0xEA);
st7701_86_spi_write_data(0xD8);
st7701_86_spi_write_data(0xA0);
st7701_86_spi_write_data(0x0D);
st7701_86_spi_write_data(0xEC);
st7701_86_spi_write_data(0xD8);
st7701_86_spi_write_data(0xA0);
st7701_86_spi_write_data(0x0F);
st7701_86_spi_write_data(0xEE);
st7701_86_spi_write_data(0xD8);
st7701_86_spi_write_data(0xA0);
st7701_86_spi_write_cmd(0xEB);
st7701_86_spi_write_data(0x02);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0xE4);
st7701_86_spi_write_data(0xE4);
st7701_86_spi_write_data(0x88);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x40);
st7701_86_spi_write_cmd(0xEC);
st7701_86_spi_write_data(0x3C);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_cmd(0xED);
st7701_86_spi_write_data(0xAB);
st7701_86_spi_write_data(0x89);
st7701_86_spi_write_data(0x76);
st7701_86_spi_write_data(0x54);
st7701_86_spi_write_data(0x02);
st7701_86_spi_write_data(0xFF);
st7701_86_spi_write_data(0xFF);
st7701_86_spi_write_data(0xFF);
st7701_86_spi_write_data(0xFF);
st7701_86_spi_write_data(0xFF);
st7701_86_spi_write_data(0xFF);
st7701_86_spi_write_data(0x20);
st7701_86_spi_write_data(0x45);
st7701_86_spi_write_data(0x67);
st7701_86_spi_write_data(0x98);
st7701_86_spi_write_data(0xBA);
st7701_86_spi_write_cmd(0xEF);
st7701_86_spi_write_data(0x10);
st7701_86_spi_write_data(0x0D);
st7701_86_spi_write_data(0x04);
st7701_86_spi_write_data(0x08);
st7701_86_spi_write_data(0x3F);
st7701_86_spi_write_data(0x1F);
st7701_86_spi_write_cmd(0xFF);
st7701_86_spi_write_data(0x77);
st7701_86_spi_write_data(0x01);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_cmd(0x3A);
st7701_86_spi_write_data(
0x66); //55/50=16bit(RGB565);66=18bit(RGB666);77?????3AH?=24bit(RGB888)
st7701_86_spi_write_cmd(0xFF);
st7701_86_spi_write_data(0x77);
st7701_86_spi_write_data(0x01);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x13);
st7701_86_spi_write_cmd(0xE8);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x0E);
st7701_86_spi_write_cmd(0xFF);
st7701_86_spi_write_data(0x77);
st7701_86_spi_write_data(0x01);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_cmd(0xFF);
st7701_86_spi_write_data(0x77);
st7701_86_spi_write_data(0x01);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x13);
st7701_86_spi_write_cmd(0xE8);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x0C);
sunxi_lcd_delay_ms(10);
st7701_86_spi_write_cmd(0xE8);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_cmd(0xFF);
st7701_86_spi_write_data(0x77);
st7701_86_spi_write_data(0x01);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_data(0x00);
st7701_86_spi_write_cmd(0x35);
st7701_86_spi_write_data(0x00); //TE ON
st7701_86_spi_write_cmd(0x36);
st7701_86_spi_write_data(0x08); //FW:00 BW:10
st7701_86_spi_write_cmd(0x21);
///BIST
// st7701_86_spi_write_cmd(0xFF);
// st7701_86_spi_write_data(0x77);
// st7701_86_spi_write_data(0x01);
// st7701_86_spi_write_data(0x00);
// st7701_86_spi_write_data(0x00);
// st7701_86_spi_write_data(0x12);
// st7701_86_spi_write_cmd(0xD1);
// st7701_86_spi_write_data(0x81);
// st7701_86_spi_write_cmd(0xD2);
// st7701_86_spi_write_data(0x06);
st7701_86_spi_write_cmd(0x11);
sunxi_lcd_delay_ms(120);
st7701_86_spi_write_cmd(0x29);
sunxi_lcd_delay_ms(120);
}
/* sel: 0:lcd0; 1:lcd1 */
static s32 LCD_user_defined_func(u32 sel, u32 para1, u32 para2, u32 para3)
{
return 0;
}
struct __lcd_panel st7701_86_panel = {
/* panel driver name, must mach the name of lcd_drv_name in sys_config.fex
*/
.name = "st7701_86",
.func = {
.cfg_panel_info = LCD_cfg_panel_info,
.cfg_open_flow = LCD_open_flow,
.cfg_close_flow = LCD_close_flow,
.lcd_user_defined_func = LCD_user_defined_func,
},
};
st7701_86.h
/*
* drivers/video/fbdev/sunxi/disp2/disp/lcd/st7789v/st7789v.h
*
* Copyright (c) 2007-2018 Allwinnertech Co., Ltd.
* Author: zhengxiaobin <zhengxiaobin@allwinnertech.com>
*
* This software is licensed under the terms of the GNU General Public
* License version 2, as published by the Free Software Foundation, and
* may be copied, distributed, and modified under those terms.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
*/
#ifndef __ST7701_86_PANEL_H__
#define __ST7701_86_PANEL_H__
#include "panels.h"
extern struct __lcd_panel st7701_86_panel;
#endif
st7701_86.h
/*
* drivers/video/fbdev/sunxi/disp2/disp/lcd/st7789v/st7789v.h
*
* Copyright (c) 2007-2018 Allwinnertech Co., Ltd.
* Author: zhengxiaobin <zhengxiaobin@allwinnertech.com>
*
* This software is licensed under the terms of the GNU General Public
* License version 2, as published by the Free Software Foundation, and
* may be copied, distributed, and modified under those terms.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
*/
#ifndef __ST7701_86_PANEL_H__
#define __ST7701_86_PANEL_H__
#include "panels.h"
extern struct __lcd_panel st7701_86_panel;
#endif
1万+
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
