【无标题】

1. Measured with a test load of 20 pF connected to VSSQ.

用连接到VSSQ的20 pF的测试负载进行测量。

2. Output slew rate for rising edge is measured between VILD(DC) to VIHD(AC) and for falling edge between VIHD(DC) to VILD(AC).

在VILD（DC）到VIHD（AC）之间测量上升沿的输出转换速率，并且在VIHD（DC）和VILD（AC）间测量下降沿的输出转摆速率。

3. The ratio of pull-up slew rate to pull-down slew rate is specified for the same temperature and voltage, over the entire temperature and voltage range. For a given output, it represents the maximum difference between pull-up and pull-down drivers due to process variation.

对于相同的温度和电压，在整个温度和电压范围内指定上拉转换速率与下拉转换速率的比率。对于给定的输出，它表示由于工艺变化导致的上拉和下拉驱动器之间的最大差异。

NOTES:

1. This specification is intended for devices with no clamp protection and is guaranteed by design.

1.本规范适用于无夹具保护的设备，并由设计保证

7.1 Driver Characteristics 驱动特征

LPDR1输出驱动器特性定义为在扩展模式寄存器中选择的全驱动强度、半驱动强度和四分之三驱动强度这三种操作。表17和表18以表格格式显示了适合输入模拟工具的数据。图45、图47和图46以图形方式显示了具体的驱动强度特征

NOTES:

1. Based on nominal impedance of 25 Ohms (Full Drive) and 55 Ohms (Half Drive) at VDDQ/2

基于VDDQ/2时25欧姆（全驱动）和55欧姆（半驱动）的标称阻抗

2. The full variation in driver current from minimum to maximum due to process, temperature and voltage will lie within the outer bounding lines of the I-V curve.

由于工艺、温度和电压的原因，驱动器电流从最小到最大的完全变化将位于I-V曲线的外部边界线内。

3. The I-V current for the optional quarter drive strength is approximately 50% of the half drive strength.

可选四分之一驱动强度的I-V电流约为半驱动强度的50%。

4. The IV current for the optional octant drive strength is approximately 25% of the half drive strength current.

可选八分之一驱动强度的IV电流约为半驱动强度电流的25%。

NOTES:

1. The IV current for the Three-Quarters Strength Driver is approximately 70% of the full drive strength current shown in Table 17.四分之三强度驱动器的IV电流约为表17中所示的全驱动强度电流的70%。

The Three-Quarters Strength Driver impedance is approximately 36 Ohms at VDDQ/2.

四分之三强度驱动器阻抗在VDDQ/2时约为36欧姆。

2. The full variation in driver current from minimum to maximum due to process, temperature and voltage will lie within the outer bounding lines of the I-V curve.

由于工艺、温度和电压的原因，驱动器电流从最小到最大的完全变化将位于I-V曲线的外部边界线内。

3. Implementation and availability of Three-Quarters Strength Driver is optional for speed bins LPDDR333 and below

四分之三强度驱动程序的实施和可用性对于速度仓LPDDR333及以下是可选的

对于速LPDDR333及以下的传输速度来讲，可选择四分之三强度驱动。

附件A（资料性）文件修订之间的差异

本表总结了本标准JESD209-B与其前身JESD209-A（2009年6月）相比所做的更改

A.3 Differences between JESD209A and JESD209

This table summarizes the changes made to this standard, JESD209-A, compared to its predecessor, JESD209 (August 2007).

A.2 Differences between JESD209 and JESD79-4A

This table summarizes the changes made to this standard, JESD209, compared to its predecessor,

JESD79-4A (November 2006). 

A.1 Differences between JESD79-4A and JESD79-4

This table briefly describes most of the changes made to this standard, JESD79-4A, compared to its predecessor, JESD79-4 (May 2006). It should be used with both Versions at hand. Some editorial changes are not included.