spi slave

`timescale 1ns / 1ps
//
// Company: 
// Engineer: 
// 
// Create Date:    20:01:22 03/10/2009 
// Design Name: 
// Module Name:    spi 
// Project Name: 
// Target Devices: 
// Tool versions: 
// Description: 
//
// Dependencies: 
//
// Revision: 
// Revision 0.01 - File Created
// Additional Comments: 
//
//

module spi(clk, SCK, MOSI, MISO, SSEL, LED);
input clk;

input SCK, SSEL, MOSI;
output MISO;

output LED;
// sync SCK to the FPGA clock using a 3-bits shift register
reg [2:0] SCKr;  always @(posedge clk) SCKr <= {SCKr[1:0], SCK};
wire SCK_risingedge = (SCKr[2:1]==2'b01);  // now we can detect SCK rising edges
wire SCK_fallingedge = (SCKr[2:1]==2'b10);  // and falling edges

// same thing for SSEL
reg [2:0] SSELr;  always @(posedge clk) SSELr <= {SSELr[1:0], SSEL};
wire SSEL_active = ~SSELr[1];  // SSEL is active low
wire SSEL_startmessage = (SSELr[2:1]==2'b10);  // message starts at falling edge
wire SSEL_endmessage = (SSELr[2:1]==2'b01);  // message stops at rising edge

// and for MOSI
reg [1:0] MOSIr;  always @(posedge clk) MOSIr <= {MOSIr[0], MOSI};
wire MOSI_data = MOSIr[1];
reg [2:0] bitcnt;  // we handle SPI in 8-bits format, so we need a 3 bits counter to count the bits as they come in
reg byte_received;  // high when a byte has been received
reg [7:0] byte_data_received;

always @(posedge clk)
begin
  if(~SSEL_active)
    bitcnt <= 3'b000;
  else
  if(SCK_risingedge)
  begin
    bitcnt <= bitcnt + 3'b001;
    byte_data_received <= {byte_data_received[6:0], MOSI_data};  // implement a shift-left register (since we receive the data MSB first)
  end
end

always @(posedge clk) byte_received <= SSEL_active && SCK_risingedge && (bitcnt==3'b111);

// we use the LSB of the data received to control an LED
reg LED;
always @(posedge clk) if(byte_received) LED <= byte_data_received[0];
reg [7:0] byte_data_sent;

reg [7:0] cnt;
always @(posedge clk) if(SSEL_startmessage) cnt<=cnt+8'h1;  // count the messages

always @(posedge clk)
if(SSEL_active)
begin
  if(SSEL_startmessage)
    byte_data_sent <= cnt;  // first byte sent in a message is the message count
  else
  if(SCK_fallingedge)
  begin
    if(bitcnt==3'b000)
      byte_data_sent <= 8'h00;  // after that, we send 0s
    else
      byte_data_sent <= {byte_data_sent[6:0], 1'b0};
  end
end

assign MISO = byte_data_sent[7];  // send MSB first
// we assume that there is only one slave on the SPI bus, so we don't bother with a tri-state buffer for MISO
// otherwise we would need to tri-state MISO when SSEL is inactive

endmodule