6.2.2UE maximum output power reduction-翻译

最新推荐文章于 2023-12-10 17:52:33 发布

AI浩

最新推荐文章于 2023-12-10 17:52:33 发布

阅读量3k

点赞数 3

分类专栏： 5G 文章标签： 5g

本文为博主原创文章，未经博主允许不得转载。

本文链接：https://blog.csdn.net/hhhhhhhhhhwwwwwwwwww/article/details/116458797

版权

5G 专栏收录该内容

13 篇文章

订阅专栏

1、测试目的

6.2.2.3中确定的RB数量是基于满足立方米制(CM)的最大功率回退(MPR)的要求。

2、测试适用

本测试要求适用于所有类型的NR UE release 15和forward。

3、测试说明

1、初始条件

初始条件是UE需要测试的一组测试配置，以及SS为使UE达到正确的测量状态而采取的步骤。根据表5.3.5-1中NR工作频带的要求，初始测试配置包括环境条件、测试频率和信道带宽。所有这些配置均应使用适用于每个信道带宽和子载波间距的测试参数进行测试，测试参数见表6.2.2.4.1-1至表6.2.2.4.1-9。上行参考测量通道(rmc)的详细信息请参见附件A.2。附件C.2中规定了PDSCH和PDCCH在测量前的配置。

Table 6.2.2.4.1-1: Test Configuration Table (Power Class 1, MPRnarrow)

Default Conditions
Test Environment as specified in TS 38.508-1 [10] subclause 4.1					Normal
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1					Low range, High range
Test Channel Bandwidths as specified in TS 38.508-1 [10] subclause 4.3.1					Lowest and Highest
Test SCS as specified in Table 5.3.5-1					Lowest, Highest
Test Parameters
Test ID	Freq	ChBw	SCS	Downlink Configuration	Uplink Configuration
		Default	Default	N/A for Maximum Power Reduction (MPR) test case	Modulation	RB allocation (NOTE 1)
1	Low				CP-OFDM 64 QAM	Outer_1RB_Left
2	High				CP-OFDM 64 QAM	Outer_1RB_Right
3	Low				CP-OFDM 64 QAM	2@0
4	High				CP-OFDM 64 QAM	2@NRB-2
5	Low				CP-OFDM 64 QAM	7@0
6	High				CP-OFDM 64 QAM	7@NRB-7
NOTE 1: 各射频分配的具体配置如表6.1-2所示。

Table 6.2.2.4.1-2: Test Configuration Table (Power Class 1, MPRWT, BWchannel ≤ 200 MHz)

Default Conditions
Test Environment as specified in TS 38.508-1 [10] subclause 4.1					Normal
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1					Low range, Mid range,High range
Test Channel Bandwidths as specified in TS 38.508-1 [10] subclause 4.3.1					Lowest and Highest supported channel bandwidth that ≤ 200 MHz
Test SCS as specified in Table 5.3.5-1					Lowest, Highest
Test Parameters
Test ID	Freq	ChBw	SCS	Downlink Configuration	Uplink Configuration
		Default	Default	N/A for Maximum Power Reduction (MPR) test case	Modulation	RB allocation (NOTE 1)
1	Low				DFT-s-OFDM PI/2 BPSK	8@0
2	High				DFT-s-OFDM PI/2 BPSK	8@NRB-8
3	Mid				DFT-s-OFDM PI/2 BPSK	Outer_Full
4	Mid				DFT-s-OFDM QPSK	Inner_Full_Region2
5	Low				DFT-s-OFDM QPSK	8@0
6	High				DFT-s-OFDM QPSK	8@NRB-8
7	Mid				DFT-s-OFDM QPSK	Outer_Full
8	Mid				DFT-s-OFDM 16 QAM	Inner_Full_Region2
9	Low				DFT-s-OFDM 16 QAM	8@0
10	High				DFT-s-OFDM 16 QAM	8@NRB-8
11	Mid				DFT-s-OFDM 16 QAM	Outer_Full
12	Low				DFT-s-OFDM 64 QAM	8@0
13	High				DFT-s-OFDM 64 QAM	8@NRB-8
14	Mid				DFT-s-OFDM 64 QAM	Outer_Full
15	Mid				DFT-s-OFDM 64 QAM	Inner_Full_Region2
16	Mid				CP-OFDM QPSK	Inner_Full_Region2
17	Low				CP-OFDM QPSK	8@0
18	High				CP-OFDM QPSK	8@NRB-8
19	Mid				CP-OFDM QPSK	Outer_Full
20	Low				CP-OFDM 16 QAM	8@0
21	High				CP-OFDM 16 QAM	8@NRB-8
22	Mid				CP-OFDM 16 QAM	Outer_Full
23	Mid				CP-OFDM 16 QAM	Inner_Full_Region2
24	Low				CP-OFDM 64 QAM	8@0
25	High				CP-OFDM 64 QAM	8@NRB-8
26	Mid				CP-OFDM 64 QAM	Outer_Full
NOTE 1: The specific configuration of each RF allocation is defined in clause 6.1-2.

Table 6.2.2.4.1-3: Test Configuration Table (Power Class 1, MPRWT, BWchannel = 400 MHz)

Default Conditions
Test Environment as specified in TS 38.508-1 [10] subclause 4.1					Normal
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1					Low range, Mid range, High range
Test Channel Bandwidths as specified in TS 38.508-1 [10] subclause 4.3.1					400 MHz
Test SCS as specified in Table 5.3.5-1					120kHz
Test Parameters
Test ID	Freq	ChBw	SCS	Downlink Configuration	Uplink Configuration
		Default	Default	N/A for Maximum Power Reduction (MPR) test case	Modulation	RB allocation (NOTE 1)
1	Low				DFT-s-OFDM PI/2 BPSK	8@0
2	High				DFT-s-OFDM PI/2 BPSK	8@NRB-8
3	Mid				DFT-s-OFDM PI/2 BPSK	Outer_Full
4	Mid				DFT-s-OFDM PI/2 BPSK	Inner_Full_Region2
5	Mid				DFT-s-OFDM QPSK	Inner_Full_Region2
6	Low				DFT-s-OFDM QPSK	8@0
7	High				DFT-s-OFDM QPSK	8@NRB-8
8	Default				DFT-s-OFDM QPSK	Outer_Full
9	Mid				DFT-s-OFDM 16 QAM	Inner_Full_Region2
10	Low				DFT-s-OFDM 16 QAM	8@0
11	High				DFT-s-OFDM 16 QAM	8@NRB-8
12	Mid				DFT-s-OFDM 16 QAM	Outer_Full
13	Low				DFT-s-OFDM 64 QAM	8@0
14	High				DFT-s-OFDM 64 QAM	8@NRB-8
15	Mid				DFT-s-OFDM 64 QAM	Outer_Full
16	Mid				CP-OFDM QPSK	Inner_Full_Region2
17	Low				CP-OFDM QPSK	8@0
18	High				CP-OFDM QPSK	8@NRB-8
19	Mid				CP-OFDM QPSK	Outer_Full
20	Low				CP-OFDM 16 QAM	8@0
21	High				CP-OFDM 16 QAM	8@NRB-8
22	Mid				CP-OFDM 16 QAM	Outer_Full
23	Mid				CP-OFDM 16 QAM	Inner_Full_Region2
24	Low				CP-OFDM 64 QAM	8@0
25	High				CP-OFDM 64 QAM	8@NRB-8
26	Mid				CP-OFDM 64 QAM	Outer_Full
NOTE 1: The specific configuration of each RF allocation is defined in clause 6.1-2.

Table 6.2.2.4.1-4: Void

Table 6.2.2.4.1-5: Void

Table 6.2.2.4.1-6: Void

Table 6.2.2.4.1-7: Test Configuration Table (Power Class 2, 3 and 4, MPRnarrow, BWchannel ≤ 200 MHz)

Default Conditions
Test Environment as specified in TS 38.508-1 [10] subclause 4.1					Normal
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1					Low range, High range
Test Channel Bandwidths as specified in TS 38.508-1 [10] subclause 4.3.1					Lowest and Highes supported channel bandwidth that ≤ 200 MHz t
Test SCS as specified in Table 5.3.5-1					Lowest, Highest
Test Parameters
Test ID	Freq	ChBw	SCS	Downlink Configuration	Uplink Configuration
		Default	Default	N/A for Maximum Power Reduction (MPR) test case	Modulation	RB allocation (NOTE 1)
1	Low				DFT-s-OFDM PI/2 BPSK	Outer_1RB_Left
2	High				DFT-s-OFDM PI/2 BPSK	Outer_1RB_Right
3	Low				DFT-s-OFDM QPSK	Outer_1RB_Left
4	High				DFT-s-OFDM QPSK	Outer_1RB_Right
NOTE 1: The specific configuration of each RF allocation is defined in Table 6.1-1.

Table 6.2.2.4.1-8: Test Configuration Table (Power Class 2, 3 and 4, MPRWT, BWchannel ≤ 200 MHz)

Default Conditions
Test Environment as specified in TS 38.508-1 [10] subclause 4.1					Normal
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1					Low range, Mid range, High range
Test Channel Bandwidths as specified in TS 38.508-1 [10] subclause 4.3.1					Lowest and Highest supported channel bandwidth that ≤ 200 MHz
Test SCS as specified in Table 5.3.5-1					Lowest, Highest
Test Parameters
Test ID	Freq	ChBw	SCS	Downlink Configuration	Uplink Configuration
		Default	Default	N/A for Maximum Power Reduction (MPR) test case	Modulation	RB allocation (NOTE 1)
1	Mid				DFT-s-OFDM PI/2 BPSK	Outer_Full
2	Mid				DFT-s-OFDM QPSK	Outer_Full
3	Mid				DFT-s-OFDM 16 QAM	Inner_Full
4	Low				DFT-s-OFDM 16 QAM	Outer_1RB_Left
5	High				DFT-s-OFDM 16 QAM	Outer_1RB_Right
6	Mid				DFT-s-OFDM 16 QAM	Outer_Full
7	Mid				DFT-s-OFDM 64 QAM	Inner_Full
8	Low				DFT-s-OFDM 64 QAM	Outer_1RB_Left
9	High				DFT-s-OFDM 64 QAM	Outer_1RB_Right
10	Mid				DFT-s-OFDM 64 QAM	Outer_Full
11	Mid				CP-OFDM QPSK	Inner_Full
12	Low				CP-OFDM QPSK	Outer_1RB_Left
13	High				CP-OFDM QPSK	Outer_1RB_Right
14	Mid				CP-OFDM QPSK	Outer_Full
15	Low				CP-OFDM 16 QAM	Outer_1RB_Left
16	High				CP-OFDM 16 QAM	Outer_1RB_Right
17	Mid				CP-OFDM 16 QAM	Outer_Full
18	Low				CP-OFDM 64 QAM	Outer_1RB_Left
19	High				CP-OFDM 64 QAM	Outer_1RB_Right
20	Mid				CP-OFDM 64 QAM	Outer_Full
NOTE 1: The specific configuration of each RF allocation is defined in Table 6.1-1.

Table 6.2.2.4.1-9: Test Configuration Table (Power Class 2, 3 and 4, MPRWT, BWchannel = 400 MHz)

Default Conditions
Test Environment as specified in TS 38.508-1 [10] subclause 4.1					Normal
Test Frequencies as specified in TS 38.508-1 [10] subclause 4.3.1					Low range, High range
Test Channel Bandwidths as specified in TS 38.508-1 [10] subclause 4.3.1					400 MHz
Test SCS as specified in Table 5.3.5-1					120kHz
Test Parameters
Test ID	Freq	ChBw	SCS	Downlink Configuration	Uplink Configuration
		Default	Default	N/A for Maximum Power Reduction (MPR) test case	Modulation	RB allocation (NOTE 1)
1	Low				DFT-s-OFDM PI/2 BPSK	Outer_1RB_Left
2	High				DFT-s-OFDM PI/2 BPSK	Outer_1RB_Right
3	Mid				DFT-s-OFDM PI/2 BPSK	Outer_Full
4	Low				DFT-s-OFDM QPSK	Outer_1RB_Left
5	High				DFT-s-OFDM QPSK	Outer_1RB_Right
6	Mid				DFT-s-OFDM QPSK	Outer_Full
7	Low				DFT-s-OFDM 16 QAM	Outer_1RB_Left
8	High				DFT-s-OFDM 16 QAM	Outer_1RB_Right
9	Mid				DFT-s-OFDM 16 QAM	Outer_Full
10	Low				DFT-s-OFDM 64 QAM	Outer_1RB_Left
11	High				DFT-s-OFDM 64 QAM	Outer_1RB_Right
12	Mid				DFT-s-OFDM 64 QAM	Outer_Full
13	Low				CP-OFDM QPSK	Outer_1RB_Left
14	High				CP-OFDM QPSK	Outer_1RB_Right
15	Mid				CP-OFDM QPSK	Outer_Full
16	Low				CP-OFDM 16 QAM	Outer_1RB_Left
17	High				CP-OFDM 16 QAM	Outer_1RB_Right
18	Mid				CP-OFDM 16 QAM	Outer_Full
19	Low				CP-OFDM 64 QAM	Outer_1RB_Left
20	High				CP-OFDM 64 QAM	Outer_1RB_Right
21	Mid				CP-OFDM 64 QAM	Outer_Full
NOTE 1: The specific configuration of each RF allocation is defined in Table 6.1-1.

2、测试步骤

1.SS通过PDCCH DCI格式0_1针对C_RNTI发送针对每个UL HARQ过程的上行链路调度信息，以根据表6.2.2.4.1-1至表6.2.2.4.1-9来调度UL RMC。由于UL没有有效载荷并且没有环回数据要发送，因此UE在UL RMC上发送上行链路MAC填充比特。

2.如附件K.1.1所述，将UE设置为通过3D EIRP扫描发现的Tx波束峰值方向。至少允许BEAM_SELECT_WAIT_TIME（NOTE 1）才能完成UE Tx波束选择。

3.在每个上行调度信息中向UE连续发送上行功率控制“ up”命令给UE； UE至少需要200毫秒才能达到PUMAX级别。至少允许BEAM_SELECT_WAIT_TIME（注1）完成UE Tx波束选择。

4. SS仅通过使用条件Tx执行TS 38.508-1 [10]第4.9.2节中指定的过程来激活UE Beamlock功能（UBF）。

5.根据测试配置，在无线电接入模式的信道带宽内，在Tx波束峰值方向上测量UE EIRP，应满足6.2.2.5中描述的要求。 EIRP测试程序在附件K.1.3中定义。测量持续时间是一个活动的上行链路子帧。 EIRP的计算考虑了两个极化角theta和phi。

6. SS通过执行TS 38.508-1 [10]第4.9.3节中指定的过程来停用UE Beamlock功能（UBF）。

注1：BEAM_SELECT_WAIT_TIME的默认值在附件K.1.1中定义。

注2：按照测试配置表6.2.2.4.1-1至表6.2.2.4.1-9中的规定，切换至DFT-s-OFDM波形时，请根据TS 38.508-1 [10发送发送NR RRCReconfiguration消息] ]条款4.6.3表4.6.3-118带有TRANSFORM_PRECODER_ENABLED条件的PUSCH-Config。

4、测试要求

第5步测量出的最大输出功率应在下表中最大输出功率和公差规定的范围内。

Table 6.2.2.5-1: UE Power Class test requirements for Power Class 1 ( for Bands n257, n258, n261 )

Test Configuration Table	Test ID	PPowerclass	MPRf,c	T(MPRf,c)	Lower limit (dBm)	Upper limit (dBm)
Table 6.2.2.4.1-1	1	40	14.4	7	18.6-TT	55
	2	40	14.4	7	18.6-TT	55
	3	40	10	5	25-TT	55
	4	40	10	5	25-TT	55
	5	40	10	5	25-TT	55
	6	40	10	5	25-TT	55
Table 6.2.2.4.1-2	1	40	5.5	5	29.5-TT	55
	2	40	5.5	5	29.5-TT	55
	3	40	5.5	5	29.5-TT	55
	4	40	3	2	35-TT	55
	5	40	6.5	5	28.5-TT	55
	6	40	6.5	5	28.5-TT	55
	7	40	6.5	5	28.5-TT	55
	8	40	4	3	33-TT	55
	9	40	6.5	5	28.5-TT	55
	10	40	6.5	5	28.5-TT	55
	11	40	6.5	5	28.5-TT	55
	12	40	6.5	5	28.5-TT	55
	13	40	6.5	5	28.5-TT	55
	14	40	6.5	5	28.5-TT	55
	15	40	5	4	31-TT	55
	16	40	4.5	4	31.5-TT	55
	17	40	7	5	28-TT	55
	18	40	7	5	28-TT	55
	19	40	7	5	28-TT	55
	20	40	7	5	28-TT	55
	21	40	7	5	28-TT	55
	22	40	7	5	28-TT	55
	23	40	5.5	5	29.5-TT	55
	24	40	7.5	5	27.5-TT	55
	256	40	7.5	5	27.5-TT	55
	26	40	7.5	5	27.5-TT	55
Table 6.2.2.4.1-3	1	40	5.5	5	29.5-TT	55
	2	40	5.5	5	29.5-TT	55
	3	40	5.5	5	29.5-TT	55
	4	40	3	2	35-TT	55
	5	40	3.5	3	33.5-TT	55
	6	40	6.5	5	28.5-TT	55
	7	40	6.5	5	28.5-TT	55
	8	40	6.5	5	28.5-TT	55
	9	40	4.5	4	31.5-TT	55
	10	40	6.5	5	28.5-TT	55
	11	40	6.5	5	28.5-TT	55
	12	40	6.5	5	28.5-TT	55
	13	40	6.5	5	28.5-TT	55
	14	40	6.5	5	28.5-TT	55
	15	40	6.5	5	28.5-TT	55
	16	40	5	4	31-TT	55
	17	40	7	5	28-TT	55
	18	40	7	5	28-TT	55
	19	40	7	5	28-TT	55
	20	40	7	5	28-TT	55
	21	40	7	5	28-TT	55
	22	40	7	5	28-TT	55
	23	40	6.5	5	28.5-TT	55
	24	40	9	5	26-TT	55
	25	40	9	5	26-TT	55
	26	40	9	5	26-TT	55

Table 6.2.2.5-1a: UE Power Class test requirements for Power Class 1 ( for Bands n260 )

Test Configuration Table	Test ID	PPowerclass	MPRf,c	T(MPRf,c)	Lower limit (dBm)	Upper limit (dBm)
Table 6.2.2.4.1-1	1	38	14.4	7	16.6-TT	55
	2	38	14.4	7	16.6-TT	55
	3	38	10	5	23-TT	55
	4	38	10	5	23-TT	55
	5	38	10	5	23-TT	55
	6	38	10	5	23-TT	55
Table 6.2.2.4.1-2	1	38	5.5	5	27.5-TT	55
	2	38	5.5	5	27.5-TT	55
	3	38	5.5	5	27.5-TT	55
	4	38	3	2	33-TT	55
	5	38	6.5	5	26.5-TT	55
	6	38	6.5	5	26.5-TT	55
	7	38	6.5	5	26.5-TT	55
	8	38	4	3	31-TT	55
	9	38	6.5	5	26.5-TT	55
	10	38	6.5	5	26.5-TT	55
	11	38	6.5	5	26.5-TT	55
	12	38	6.5	5	26.5-TT	55
	13	38	6.5	5	26.5-TT	55
	14	38	6.5	5	26.5-TT	55
	15	38	5	4	29-TT	55
	16	38	4.5	4	29.5-TT	55
	17	38	7	5	26-TT	55
	18	38	7	5	26-TT	55
	19	38	7	5	26-TT	55
	20	38	7	5	26-TT	55
	21	38	7	5	26-TT	55
	22	38	7	5	26-TT	55
	23	38	5.5	5	27.5-TT	55
	24	38	7.5	5	25.5-TT	55
	25	38	7.5	5	25.5-TT	55
	26	38	7.5	5	25.5-TT	55
Table 6.2.2.4.1-3	1	38	5.5	5	27.5-TT	55
	2	38	5.5	5	27.5-TT	55
	3	38	5.5	5	27.5-TT	55
	4	38	3	2	33-TT	55
	5	38	3.5	3	31.5-TT	55
	6	38	6.5	5	26.5-TT	55
	7	38	6.5	5	26.5-TT	55
	8	38	6.5	5	26.5-TT	55
	9	38	4.5	4	29.5-TT	55
	10	38	6.5	5	26.5-TT	55
	11	38	6.5	5	26.5-TT	55
	12	38	6.5	5	26.5-TT	55
	13	38	6.5	5	26.5-TT	55
	14	38	6.5	5	26.5-TT	55
	15	38	6.5	5	26.5-TT	55
	16	38	5	4	29-TT	55
	17	38	7	5	26-TT	55
	18	38	7	5	26-TT	55
	19	38	7	5	26-TT	55
	20	38	7	5	26-TT	55
	21	38	7	5	26-TT	55
	22	38	7	5	26-TT	55
	23	38	6.5	5	26.5-TT	55
	24	38	9	5	24-TT	55
	25	38	9	5	24-TT	55
	26	38	9	5	24-TT	55

Table 6.2.2.5-2: UE Power Class test requirements for Power Class 2

Test Configuration Table	Test ID	PPowerclass	MPRf,c	T(MPRf,c)	Lower limit (dBm)	Upper limit (dBm)
Table 6.2.2.4.1-7	1	29	2.5	2	24.5-TT	43
	2	29	2.5	2	24.5-TT	43
	3	29	2.5	2	24.5-TT	43
	4	29	2.5	2	24.5-TT	43
Table 6.2.2.4.1-8	1	29	2	1.5	25.5-TT	43
	2	29	2	1.5	25.5-TT	43
	3	29	3	2	24-TT	43
	4	29	3.5	3	22.5-TT	43
	5	29	3.5	3	22.5-TT	43
	6	29	3.5	3	22.5-TT	43
	7	29	5	4	20-TT	43
	8	29	5.5	5	18.5-TT	43
	9	29	5.5	5	18.5-TT	43
	10	29	5.5	5	18.5-TT	43
	11	29	3.5	3	22.5-TT	43
	12	29	4	3	22-TT	43
	13	29	4	3	22-TT	43
	14	29	4	3	22-TT	43
	15	29	5	4	20-TT	43
	16	29	5	4	20-TT	43
	17	29	5	4	20-TT	43
	18	29	7	5	17-TT	43
	19	29	7	5	17-TT	43
	20	29	7	5	17-TT	43
Table 6.2.2.4.1-9	1	29	3	2	24-TT	43
	2	29	3	2	24-TT	43
	3	29	3	2	24-TT	43
	4	29	3	2	24-TT	43
	5	29	3	2	24-TT	43
	6	29	3	2	24-TT	43
	7	29	4.5	4	20.5-TT	43
	8	29	4.5	4	20.5-TT	43
	9	29	4.5	4	20.5-TT	43
	10	29	6.5	5	17.5-TT	43
	11	29	6.5	5	17.5-TT	43
	12	29	6.5	5	17.5-TT	43
	13	29	5	4	20-TT	43
	14	29	5	4	20-TT	43
	15	29	5	4	20-TT	43
	16	29	6.5	5	17.5-TT	43
	17	29	6.5	5	17.5-TT	43
	18	29	6.5	5	17.5-TT	43
	19	29	9	5	15-TT	43
	20	29	9	5	15-TT	43
	21	29	9	5	15-TT	43

Table 6.2.2.5-3: UE Power Class test requirements for Power Class 3 ( n257, 258, 261 )

Test Configuration Table	Test ID	PPowerclass	MPRf,c	T(MPRf,c)	Lower limit (dBm)	Upper limit (dBm)
Table 6.2.2.4.1-7	1	22.4	2.5	2	17.9-TT-ΔMBP,n	43
	2	22.4	2.5	2	17.9-TT-ΔMBP,n	43
	3	22.4	2.5	2	17.9-TT-ΔMBP,n	43
	4	22.4	2.5	2	17.9-TT-ΔMBP,n	43
Table 6.2.2.4.1-8	1	22.4	2	1.5	18.9-TT-ΔMBP,n	43
	2	22.4	2	1.5	18.9-TT-ΔMBP,n	43
	3	22.4	3	2	17.4-TT-ΔMBP,n	43
	4	22.4	3.5	3	15.9-TT-ΔMBP,n	43
	5	22.4	3.5	3	15.9-TT-ΔMBP,n	43
	6	22.4	3.5	3	15.9-TT-ΔMBP,n	43
	7	22.4	5	4	13.4-TT-ΔMBP,n	43
	8	22.4	5.5	5	11.9-TT-ΔMBP,n	43
	9	22.4	5.5	5	11.9-TT-ΔMBP,n	43
	10	22.4	5.5	5	11.9-TT-ΔMBP,n	43
	11	22.4	3.5	3	15.9-TT-ΔMBP,n	43
	12	22.4	4	3	15.4-TT-ΔMBP,n	43
	13	22.4	4	3	15.4-TT-ΔMBP,n	43
	14	22.4	4	3	15.4-TT-ΔMBP,n	43
	15	22.4	5	4	13.4-TT-ΔMBP,n	43
	16	22.4	5	4	13.4-TT-ΔMBP,n	43
	17	22.4	5	4	13.4-TT-ΔMBP,n	43
	18	22.4	7	5	10.4-TT-ΔMBP,n	43
	19	22.4	7	5	10.4-TT-ΔMBP,n	43
	20	22.4	7	5	10.4-TT-ΔMBP,n	43
Table 6.2.2.4.1-9	1	22.4	3	2	17.4-TT-ΔMBP,n	43
	2	22.4	3	2	17.4-TT-ΔMBP,n	43
	3	22.4	3	2	17.4-TT-ΔMBP,n	43
	4	22.4	3	2	17.4-TT-ΔMBP,n	43
	5	22.4	3	2	17.4-TT-ΔMBP,n	43
	6	22.4	3	2	17.4-TT-ΔMBP,n	43
	7	22.4	4.5	4	13.9-TT-ΔMBP,n	43
	8	22.4	4.5	4	13.9-TT-ΔMBP,n	43
	9	22.4	4.5	4	13.9-TT-ΔMBP,n	43
	10	22.4	6.5	5	10.9-TT-ΔMBP,n	43
	11	22.4	6.5	5	10.9-TT-ΔMBP,n	43
	12	22.4	6.5	5	10.9-TT-ΔMBP,n	43
	13	22.4	5	4	13.4-TT-ΔMBP,n	43
	14	22.4	5	4	13.4-TT-ΔMBP,n	43
	15	22.4	5	4	13.4-TT-ΔMBP,n	43
	16	22.4	6.5	5	10.9-TT-ΔMBP,n	43
	17	22.4	6.5	5	10.9-TT-ΔMBP,n	43
	18	22.4	6.5	5	10.9-TT-ΔMBP,n	43
	19	22.4	9	5	8.4-TT-ΔMBP,n	43
	20	22.4	9	5	8.4-TT-ΔMBP,n	43
	21	22.4	9	5	8.4-TT-ΔMBP,n	43
Note 1: ΔMBP,n为TS38.508-2表a . 4.39 -2中UE对测试频带声明的多频段宽松因子。本声明应满足第6.2.1.1.3.3条的要求。 Note 2: 需要测试所有UE支持的频带，以确保多频段宽松声明符合要求。 Note 3: 在第6.2.1.1.3.3条中定义所有支持的FR2频带上的最大允许ΔMBP,n的和。 Note 4: 单频段的ΔMBP,n是0

Table 6.2.2.5-3a: UE Power Class test requirements for Power Class 3 ( n260 )

Test Configuration Table	Test ID	PPowerclass	MPRf,c	T(MPRf,c)	Lower limit (dBm)	Upper limit (dBm)
Table 6.2.2.4.1-7	1	20.6	2.5	2	16.1-TT-ΔMBP,n	43
	2	20.6	2.5	2	16.1-TT-ΔMBP,n	43
	3	20.6	2.5	2	16.1-TT-ΔMBP,n	43
	4	20.6	2.5	2	16.1-TT-ΔMBP,n	43
Table 6.2.2.4.1-8	1	20.6	2	1.5	17.1-TT-ΔMBP,n	43
	2	20.6	2	1.5	17.1-TT-ΔMBP,n	43
	3	20.6	3	2	15.6-TT-ΔMBP,n	43
	4	20.6	3.5	3	14.1-TT-ΔMBP,n	43
	5	20.6	3.5	3	14.1-TT-ΔMBP,n	43
	6	20.6	3.5	3	14.1-TT-ΔMBP,n	43
	7	20.6	5	4	11.6-TT-ΔMBP,n	43
	8	20.6	5.5	5	10.1-TT-ΔMBP,n	43
	9	20.6	5.5	5	10.1-TT-ΔMBP,n	43
	10	20.6	5.5	5	10.1-TT-ΔMBP,n	43
	11	20.6	3.5	3	14.1-TT-ΔMBP,n	43
	12	20.6	4	3	13.6-TT-ΔMBP,n	43
	13	20.6	4	3	13.6-TT-ΔMBP,n	43
	14	20.6	4	3	13.6-TT-ΔMBP,n	43
	15	20.6	5	4	11.6-TT-ΔMBP,n	43
	16	20.6	5	4	11.6-TT-ΔMBP,n	43
	17	20.6	5	4	11.6-TT-ΔMBP,n	43
	18	20.6	7	5	8.6-TT-ΔMBP,n	43
	19	20.6	7	5	8.6-TT-ΔMBP,n	43
	20	20.6	7	5	8.6-TT-ΔMBP,n	43
Table 6.2.2.4.1-9	1	20.6	3	2	15.6-TT-ΔMBP,n	43
	2	20.6	3	2	15.6-TT-ΔMBP,n	43
	3	20.6	3	2	15.6-TT-ΔMBP,n	43
	4	20.6	3	2	15.6-TT-ΔMBP,n	43
	5	20.6	3	2	15.6-TT-ΔMBP,n	43
	6	20.6	3	2	15.6-TT-ΔMBP,n	43
	7	20.6	4.5	4	12.1-TT-ΔMBP,n	43
	8	20.6	4.5	4	12.1-TT-ΔMBP,n	43
	9	20.6	4.5	4	12.1-TT-ΔMBP,n	43
	10	20.6	6.5	5	9.1-TT-ΔMBP,n	43
	11	20.6	6.5	5	9.1-TT-ΔMBP,n	43
	12	20.6	6.5	5	9.1-TT-ΔMBP,n	43
	13	20.6	5	4	11.6-TT-ΔMBP,n	43
	14	20.6	5	4	11.6-TT-ΔMBP,n	43
	15	20.6	5	4	11.6-TT-ΔMBP,n	43
	16	20.6	6.5	5	9.1-TT-ΔMBP,n	43
	17	20.6	6.5	5	9.1-TT-ΔMBP,n	43
	18	20.6	6.5	5	9.1-TT-ΔMBP,n	43
	19	20.6	9	5	6.6-TT-ΔMBP,n	43
	20	20.6	9	5	6.6-TT-ΔMBP,n	43
	21	20.6	9	5	6.6-TT-ΔMBP,n	43
Note 1: ΔMBP,n为TS38.508-2表A.4.3.9 -2中UE对测试频带声明的多频段宽松因子。本声明应满足第6.2.1.1.3.3条的要求。 Note 2: 需要测试所有UE支持的频带，以确保多频段宽松声明符合要求。 Note 3: 在第6.2.1.1.3.3条中定义所有支持的FR2频段上的最大允许ΔMBP,n的和。 Note 4: 单频段的ΔMBP,n是0

Table 6.2.2.5-3b: Test Tolerance (Power class 3)

Test Metric	FR2a	FR2b
Quiet Zone size ≤ 30 cm	3.11 dB	3.11 dB

Table 6.2.2.5-4: UE Power Class test requirements for Power Class 4 ( n257, 258, 261 )

Test Configuration Table	Test ID	PPowerclass	MPRf,c	T(MPRf,c)	Lower limit (dBm)	Upper limit (dBm)
Table 6.2.2.4.1-7	1	34	2.5	2	29.5-TT	43
	2	34	2.5	2	29.5-TT	43
	3	34	2.5	2	29.5-TT	43
	4	34	2.5	2	29.5-TT	43
Table 6.2.2.4.1-8	1	34	2	1.5	30.5-TT	43
	2	34	2	1.5	30.5-TT	43
	3	34	3	2	29-TT	43
	4	34	3.5	3	27.5-TT	43
	5	34	3.5	3	27.5-TT	43
	6	34	3.5	3	27.5-TT	43
	7	34	5	4	25-TT	43
	8	34	5.5	5	23.5-TT	43
	9	34	5.5	5	23.5-TT	43
	10	34	5.5	5	23.5-TT	43
	11	34	3.5	3	27.5-TT	43
	12	34	4	3	27-TT	43
	13	34	4	3	27-TT	43
	14	34	4	3	27-TT	43
	15	34	5	4	25-TT	43
	16	34	5	4	25-TT	43
	17	34	5	4	25-TT	43
	18	34	7	5	22-TT	43
	19	34	7	5	22-TT	43
	20	34	7	5	22-TT	43
Table 6.2.2.4.1-9	1	34	3	2	29-TT	43
	2	34	3	2	29-TT	43
	3	34	3	2	29-TT	43
	4	34	3	2	29-TT	43
	5	34	3	2	29-TT	43
	6	34	3	2	29-TT	43
	7	34	4.5	4	25.5-TT	43
	8	34	4.5	4	25.5-TT	43
	9	34	4.5	4	25.5-TT	43
	10	34	6.5	5	22.5-TT	43
	11	34	6.5	5	22.5-TT	43
	12	34	6.5	5	22.5-TT	43
	13	34	5	4	25-TT	43
	14	34	5	4	25-TT	43
	15	34	5	4	25-TT	43
	16	34	6.5	5	22.5-TT	43
	17	34	6.5	5	22.5-TT	43
	18	34	6.5	5	22.5-TT	43
	19	34	9	5	20-TT	43
	20	34	9	5	20-TT	43
	21	34	9	5	20-TT	43

Table 6.2.2.5-4a: UE Power Class test requirements for Power Class 4 ( n260 )

Test Configuration Table	Test ID	PPowerclass	MPRf,c	T(MPRf,c)	Lower limit (dBm)	Upper limit (dBm)
Table 6.2.2.4.1-7	1	31	2.5	2	26.5-TT	43
	2	31	2.5	2	26.5-TT	43
	3	31	2.5	2	26.5-TT	43
	4	31	2.5	2	26.5-TT	43
Table 6.2.2.4.1-8	1	31	2	1.5	27.5-TT	43
	2	31	2	1.5	27.5-TT	43
	3	31	3	2	26-TT	43
	4	31	3.5	3	24.5-TT	43
	5	31	3.5	3	24.5-TT	43
	6	31	3.5	3	24.5-TT	43
	7	31	5	4	22-TT	43
	8	31	5.5	5	20.5-TT	43
	9	31	5.5	5	20.5-TT	43
	10	31	5.5	5	20.5-TT	43
	11	31	3.5	3	24.5-TT	43
	12	31	4	3	24-TT	43
	13	31	4	3	24-TT	43
	14	31	4	3	24-TT	43
	15	31	5	4	22-TT	43
	16	31	5	4	22-TT	43
	17	31	5	4	22-TT	43
	18	31	7	5	19-TT	43
	19	31	7	5	19-TT	43
	20	31	7	5	19-TT	43
Table 6.2.2.4.1-9	1	31	3	2	26-TT	43
	2	31	3	2	26-TT	43
	3	31	3	2	26-TT	43
	4	31	3	2	26-TT	43
	5	31	3	2	26-TT	43
	6	31	3	2	26-TT	43
	7	31	4.5	4	22.5-TT	43
	8	31	4.5	4	22.5-TT	43
	9	31	4.5	4	22.5-TT	43
	10	31	6.5	5	19.5-TT	43
	11	31	6.5	5	19.5-TT	43
	12	31	6.5	5	19.5-TT	43
	13	31	5	4	22-TT	43
	14	31	5	4	22-TT	43
	15	31	5	4	22-TT	43
	16	31	6.5	5	19.5-TT	43
	17	31	6.5	5	19.5-TT	43
	18	31	6.5	5	19.5-TT	43
	19	31	9	5	17-TT	43
	20	31	9	5	17-TT	43
	21	31	9	5	17-TT	43