MSP430f5529LP的四针OLED显示（寄存器）

苍白信纸

已于 2023-07-23 08:52:08 修改

阅读量510

点赞数 2

分类专栏： MSP430 文章标签：单片机嵌入式硬件

于 2023-07-14 17:32:32 首次发布

本文链接：https://blog.csdn.net/jiang_2047/article/details/131727576

版权

MSP430 专栏收录该内容

4 篇文章 6 订阅

订阅专栏

虽然说是寄存器操作，但是作为一个外设它本身影响不大，在oled.h里面更改set和clr的宏定义就可以了。话不多说，直接上代码好了，有关接线可以自行在oled.h里面查。注意这里用的是四针OLED。

type.h的代码

#ifndef TYPE_H_
#define TYPE_H_

#define u32 unsigned int
#define u16 unsigned short
#define u8 unsigned char
#define uint32_t unsigned int
#define uint16_t unsigned short
#define uint8_t unsigned char

#endif

oled.c的代码

#include "oled.h"
#include "font.h"

void IIC_Start()    //启动IIC
{
    OLED_SCLK_Set();
    OLED_SDIN_Set();
    OLED_SDIN_Clr();
    OLED_SCLK_Clr();
}
void IIC_Stop()     //停止IIC
{
    OLED_SCLK_Set();
//  OLED_SCLK_Clr();
    OLED_SDIN_Clr();
    OLED_SDIN_Set();
}
void IIC_Wait_Ack()     //等待响应
{
    OLED_SCLK_Set();    //P3OUT|=BIT5
    OLED_SCLK_Clr();    //P3OUT&=~BIT5
}
void Write_IIC_Byte(u8 IIC_Byte)     //通过IIC通信
{
    u8 i;
    u8 m,da;

    da=IIC_Byte;
    OLED_SCLK_Clr();    //P3OUT &= ~BIT5
    for(i=0;i<8;i++)
    {
        m=da;
        //  OLED_SCLK_Clr();
        m=m&0x80;
        if(m==0x80)
        {
            OLED_SDIN_Set();    //P3OUT |= BIT6
        }
        else OLED_SDIN_Clr();   //P3OUT &= ~BIT6
            da=da<<1;
        OLED_SCLK_Set();    //P3OUT |= BIT5
        OLED_SCLK_Clr();    //P3OUT &= ~BIT5
    }
}
void Write_IIC_Command(u8 IIC_Command)   //向OLED写入命令
{
   IIC_Start();
   Write_IIC_Byte(0x78);
   IIC_Wait_Ack();
   Write_IIC_Byte(0x00);
   IIC_Wait_Ack();
   Write_IIC_Byte(IIC_Command);
   IIC_Wait_Ack();
   IIC_Stop();
}
void Write_IIC_Data(u8 IIC_Data)     //写数据
{
    IIC_Start();
    Write_IIC_Byte(0x78);
    IIC_Wait_Ack();
    Write_IIC_Byte(0x40);
    IIC_Wait_Ack();
    Write_IIC_Byte(IIC_Data);
    IIC_Wait_Ack();
    IIC_Stop();
}
void OLED_WR_Byte(unsigned dat,unsigned cmd)    //OLED写入字节，就是引用上面两个函数
{
    if(cmd)
        Write_IIC_Data(dat);        //数据
    else
        Write_IIC_Command(dat);     //命令
}
void fill_picture(u8 fill_Data)      //图片
{
    u8 m,n;
    for(m=0;m<8;m++)
    {
        OLED_WR_Byte(0xb0+m,0);     //页地址
        OLED_WR_Byte(0x00,0);       //设置低八位
        OLED_WR_Byte(0x10,0);       //设置高八位

        for(n=0;n<128;n++)
            OLED_WR_Byte(fill_Data,1);
    }
}
void Delay_1ms(u16 Del_1ms)
{
    unsigned char j;
    while(Del_1ms--)
    {
        for(j=0;j<123;j++);
    }
}
void OLED_Set_Pos(u8 x, u8 y)     //设置显示位置
{
    OLED_WR_Byte(0xb0+y,OLED_CMD);
    OLED_WR_Byte(((x&0xf0)>>4)|0x10,OLED_CMD);
    OLED_WR_Byte((x&0x0f),OLED_CMD);
}
void OLED_Display_On(void)              //开启显示
{
    OLED_WR_Byte(0X8D,OLED_CMD);
    OLED_WR_Byte(0X14,OLED_CMD);        //DCDC ON
    OLED_WR_Byte(0XAF,OLED_CMD);        //DISPLAY ON
}
void OLED_Display_Off(void)             //关闭显示
{
    OLED_WR_Byte(0X8D,OLED_CMD);
    OLED_WR_Byte(0X10,OLED_CMD);        //DCDC OFF
    OLED_WR_Byte(0XAE,OLED_CMD);        //DISPLAY OFF
}
void OLED_Clear(void)                   //清屏，清完是黑的
{
    u8 i,n;
    for(i=0;i<8;i++)                    //y = 8 清屏y轴的8行
    {
        OLED_WR_Byte (0xb0+i,OLED_CMD); //0111 0000 + i ，选中清屏的行
        OLED_WR_Byte (0x00,OLED_CMD);
        OLED_WR_Byte (0x10,OLED_CMD);   //0001 0000
        for(n=0;n<128;n++)              //x = 128 清屏x轴的128列
            OLED_WR_Byte(0,OLED_DATA);
    }
}
void OLED_On(void)  //开启OLED
{
    u8 i,n;
    for(i=0;i<8;i++)
    {
        OLED_WR_Byte (0xb0+i,OLED_CMD);
        OLED_WR_Byte (0x00,OLED_CMD);
        OLED_WR_Byte (0x10,OLED_CMD);
        for(n=0;n<128;n++)OLED_WR_Byte(1,OLED_DATA);
    }
}
/*
x:0~127    y:0~63    size:16/12
显示字符，只能显示单个字符
*/
void OLED_ShowChar(u8 x,u8 y,u8 chr,u8 Char_Size)
{
    unsigned char c = 0,i = 0;
    c = chr-' ';
    if(x > Max_Column - 1)
    {
        x = 0;y = y+2;
    }
    if(Char_Size ==16)
    {
        OLED_Set_Pos(x,y);
        for(i = 0; i < 8; i++)
        OLED_WR_Byte( F8X16[c*16+i], OLED_DATA);
        OLED_Set_Pos(x,y+1);
        OLED_WR_Byte( F8X16[c*16+i+8], OLED_DATA);
    }
    else
    {
        OLED_Set_Pos(x,y);
        for(i = 0; i < 6; i++)
            OLED_WR_Byte(F6x8[c][i], OLED_DATA);
    }
}
/*
 * 求m的n次方
 * result = m * m * m * m....
 */
u32 oled_pow(u8 m,u8 n)
{
    u32 result = 1;
    while(n--) result *= m;
    return result;
}
/*
显示数字
x:行    y:列    num:要显示的数字    len:数字位数    size2:每一个数字的间隔
OLED_ShowNum(0,1,1234,4,8);
num的数字可为变量，例：OLED_ShowNum(0,1,date,4,8);
*/
void OLED_ShowNum(u8 x,u8 y,u32 num,u8 len,u8 size2)
{
    u8 t,temp;
    u8 enshow = 0;
    for(t = 0; t < len; t++)
    {
        temp=(num/oled_pow(10,len-t-1))%10;
        if(enshow==0&&t<(len-1))
        {
            if(temp==0)
            {
                OLED_ShowChar(x+size2*t,y,' ',size2);
                continue;
            }
            else
                enshow=1;
        }
        OLED_ShowChar(x+size2*t,y,temp+'0',size2);
    }
}
//根据具体使用情况修改
void OLED_ShowVI(u8 x,u8 y,u32 num,u8 size2)
{
    OLED_ShowNum( x+size2*4-1, y, num%10, 1, size2);
    OLED_ShowNum( x+size2*3-1, y, num/10%10, 1, size2);
    OLED_ShowNum( x+size2*2-1, y, num/100%10, 1, size2);
    OLED_ShowString( x+size2*1-1, y, ".", size2);
    OLED_ShowNum( x-1,y, num/1000, 1, size2);
}
//显示字符串
//OLED_ShowString(0,4,"DZCXXH",8);
void OLED_ShowString(u8 x,u8 y,u8 *chr,u8 Char_Size)
{
    unsigned char j=0;
    while (chr[j]!='\0')
    {
        OLED_ShowChar(x,y,chr[j],Char_Size);
        x+=8;
        if(x>120)
        {
            x=0;
            y+=2;
        }
        j++;
    }
}
//显示汉字
//使用：OLED_ShowCHinese(0,4,0);    //"电"
//x：列    y：行    no:数组中第几个汉字
void OLED_ShowCHinese(u8 x,u8 y,u8 no)
{
    u8 t,adder=0;
    OLED_Set_Pos(x,y);
    for(t=0;t<16;t++)
    {
        OLED_WR_Byte(DPJ[2*no][t],OLED_DATA);
        adder+=1;
    }
    OLED_Set_Pos(x,y+1);
    for(t=0;t<16;t++)
    {
        OLED_WR_Byte(DPJ[2*no+1][t],OLED_DATA);
        adder+=1;
    }
}
//绘制图像
void OLED_DrawBMP(u8 x0, u8 y0,u8 x1, u8 y1,u8 BMP[])
{
    u16 j=0;
    u8 x,y;

    if(y1%8==0)
        y=y1%8;
    else
        y=y1%8+1;
    for(y=y0;y<y1;y++)
    {
        OLED_Set_Pos(x0,y);
        for(x=x0;x<x1;x++)
        {
            OLED_WR_Byte(BMP[j++],OLED_DATA);
        }
    }
}
//OLED初始化模块
void OLED_Init(void)
{
    //若使用其他端口，这里要修改为对应端口
    P3DIR |= BIT5+BIT6;             //设置为输出
    OLED_WR_Byte(0xAE,OLED_CMD);    //显示关闭
    OLED_WR_Byte(0x00,OLED_CMD);    //设置低列地址
    OLED_WR_Byte(0x10,OLED_CMD);    //设置高位列地址
    OLED_WR_Byte(0x40,OLED_CMD);    //设置起始行地址
    OLED_WR_Byte(0xB0,OLED_CMD);    //设置页面地址
    OLED_WR_Byte(0x81,OLED_CMD);    //联合控制
    OLED_WR_Byte(0xFF,OLED_CMD);    //128
    OLED_WR_Byte(0xA1,OLED_CMD);    //设置段重映射
    OLED_WR_Byte(0xA6,OLED_CMD);    //--normal / reverse
    OLED_WR_Byte(0xA8,OLED_CMD);    //--set multiplex ratio(1 to 64)
    OLED_WR_Byte(0x3F,OLED_CMD);    //--1/32 duty
    OLED_WR_Byte(0xC8,OLED_CMD);    //Com scan direction
    OLED_WR_Byte(0xD3,OLED_CMD);    //-set display offset
    OLED_WR_Byte(0x00,OLED_CMD);
    OLED_WR_Byte(0xD5,OLED_CMD);    //set osc division
    OLED_WR_Byte(0x80,OLED_CMD);
    OLED_WR_Byte(0xD8,OLED_CMD);    //set area color mode off
    OLED_WR_Byte(0x05,OLED_CMD);
    OLED_WR_Byte(0xD9,OLED_CMD);    //Set Pre-Charge Period
    OLED_WR_Byte(0xF1,OLED_CMD);
    OLED_WR_Byte(0xDA,OLED_CMD);    //set com pin configuartion
    OLED_WR_Byte(0x12,OLED_CMD);
    OLED_WR_Byte(0xDB,OLED_CMD);    //set Vcomh
    OLED_WR_Byte(0x30,OLED_CMD);
    OLED_WR_Byte(0x8D,OLED_CMD);    //set charge pump enable
    OLED_WR_Byte(0x14,OLED_CMD);
    OLED_WR_Byte(0xAF,OLED_CMD);    //打开oled面板
}

oled.h的代码

SCL接P3.5 SDA接P3.6（记得在main函数里面复用P3.5和P3.6）

#ifndef __OLED_H
#define __OLED_H

#include <msp430.h>
#include "type.h"

#define OLED_MODE 0
#define SIZE 8
#define XLevelL     0x00
#define XLevelH     0x10
#define Max_Column  128
#define Max_Row     64
#define Brightness  0xFF
#define X_WIDTH     128
#define Y_WIDTH     64

#define OLED_SCLK_Clr() P3OUT &= ~BIT5  //SCL
#define OLED_SCLK_Set() P3OUT |= BIT5

#define OLED_SDIN_Clr() P3OUT &= ~BIT6  //SDA
#define OLED_SDIN_Set() P3OUT |= BIT6

#define OLED_CMD    0
#define OLED_DATA   1

void Picture();
void IIC_Stop();
void IIC_Start();
void IIC_Wait_Ack();
void OLED_Init(void);
void OLED_Clear(void);
void OLED_Display_On(void);
void Delay_1ms(u16 Del_1ms);
void OLED_Display_Off(void);
void OLED_Set_Pos(u8 x, u8 y);
void fill_picture(u8 fill_Data);
void Write_IIC_Data(u8 IIC_Data);
void Write_IIC_Byte(u8 IIC_Byte);
void OLED_DrawPoint(u8 x,u8 y,u8 t);
void Write_IIC_Command(u8 IIC_Command);
void OLED_ShowCHinese(u8 x,u8 y,u8 no);
void OLED_ShowVI(u8 x,u8 y,u32 num,u8 size);
void OLED_WR_Byte(unsigned dat,unsigned cmd);
void OLED_Fill(u8 x1,u8 y1,u8 x2,u8 y2,u8 dot);
void OLED_ShowChar(u8 x,u8 y,u8 chr,u8 Char_Size);
void OLED_ShowNum(u8 x,u8 y,u32 num,u8 len,u8 size);
void OLED_ShowString(u8 x,u8 y, u8 *p,u8 Char_Size);
void OLED_DrawBMP(u8 x0, u8 y0,u8 x1, u8 y1,u8 BMP[]);

#endif

font.h的代码，因为MSP430的资源有限不能安装本地字库，所以想要显示汉字需要取模再添加一个汉字数组。

#ifndef OLEDFONT_H_
#define OLEDFONT_H_

const unsigned char F6x8[][6] =
{
    0x00, 0x00, 0x00, 0x00, 0x00, 0x00,// sp
    0x00, 0x00, 0x00, 0x2f, 0x00, 0x00,// !
    0x00, 0x00, 0x07, 0x00, 0x07, 0x00,// "
    0x00, 0x14, 0x7f, 0x14, 0x7f, 0x14,// #
    0x00, 0x24, 0x2a, 0x7f, 0x2a, 0x12,// $
    0x00, 0x62, 0x64, 0x08, 0x13, 0x23,// %
    0x00, 0x36, 0x49, 0x55, 0x22, 0x50,// &
    0x00, 0x00, 0x05, 0x03, 0x00, 0x00,// '
    0x00, 0x00, 0x1c, 0x22, 0x41, 0x00,// (
    0x00, 0x00, 0x41, 0x22, 0x1c, 0x00,// )
    0x00, 0x14, 0x08, 0x3E, 0x08, 0x14,// *
    0x00, 0x08, 0x08, 0x3E, 0x08, 0x08,// +
    0x00, 0x00, 0x00, 0xA0, 0x60, 0x00,// ,
    0x00, 0x08, 0x08, 0x08, 0x08, 0x08,// -
    0x00, 0x00, 0x60, 0x60, 0x00, 0x00,// .
    0x00, 0x20, 0x10, 0x08, 0x04, 0x02,// /
    0x00, 0x3E, 0x51, 0x49, 0x45, 0x3E,// 0
    0x00, 0x00, 0x42, 0x7F, 0x40, 0x00,// 1
    0x00, 0x42, 0x61, 0x51, 0x49, 0x46,// 2
    0x00, 0x21, 0x41, 0x45, 0x4B, 0x31,// 3
    0x00, 0x18, 0x14, 0x12, 0x7F, 0x10,// 4
    0x00, 0x27, 0x45, 0x45, 0x45, 0x39,// 5
    0x00, 0x3C, 0x4A, 0x49, 0x49, 0x30,// 6
    0x00, 0x01, 0x71, 0x09, 0x05, 0x03,// 7
    0x00, 0x36, 0x49, 0x49, 0x49, 0x36,// 8
    0x00, 0x06, 0x49, 0x49, 0x29, 0x1E,// 9
    0x00, 0x00, 0x36, 0x36, 0x00, 0x00,// :
    0x00, 0x00, 0x56, 0x36, 0x00, 0x00,// ;
    0x00, 0x08, 0x14, 0x22, 0x41, 0x00,// <
    0x00, 0x14, 0x14, 0x14, 0x14, 0x14,// =
    0x00, 0x00, 0x41, 0x22, 0x14, 0x08,// >
    0x00, 0x02, 0x01, 0x51, 0x09, 0x06,// ?
    0x00, 0x32, 0x49, 0x59, 0x51, 0x3E,// @
    0x00, 0x7C, 0x12, 0x11, 0x12, 0x7C,// A
    0x00, 0x7F, 0x49, 0x49, 0x49, 0x36,// B
    0x00, 0x3E, 0x41, 0x41, 0x41, 0x22,// C
    0x00, 0x7F, 0x41, 0x41, 0x22, 0x1C,// D
    0x00, 0x7F, 0x49, 0x49, 0x49, 0x41,// E
    0x00, 0x7F, 0x09, 0x09, 0x09, 0x01,// F
    0x00, 0x3E, 0x41, 0x49, 0x49, 0x7A,// G
    0x00, 0x7F, 0x08, 0x08, 0x08, 0x7F,// H
    0x00, 0x00, 0x41, 0x7F, 0x41, 0x00,// I
    0x00, 0x20, 0x40, 0x41, 0x3F, 0x01,// J
    0x00, 0x7F, 0x08, 0x14, 0x22, 0x41,// K
    0x00, 0x7F, 0x40, 0x40, 0x40, 0x40,// L
    0x00, 0x7F, 0x02, 0x0C, 0x02, 0x7F,// M
    0x00, 0x7F, 0x04, 0x08, 0x10, 0x7F,// N
    0x00, 0x3E, 0x41, 0x41, 0x41, 0x3E,// O
    0x00, 0x7F, 0x09, 0x09, 0x09, 0x06,// P
    0x00, 0x3E, 0x41, 0x51, 0x21, 0x5E,// Q
    0x00, 0x7F, 0x09, 0x19, 0x29, 0x46,// R
    0x00, 0x46, 0x49, 0x49, 0x49, 0x31,// S
    0x00, 0x01, 0x01, 0x7F, 0x01, 0x01,// T
    0x00, 0x3F, 0x40, 0x40, 0x40, 0x3F,// U
    0x00, 0x1F, 0x20, 0x40, 0x20, 0x1F,// V
    0x00, 0x3F, 0x40, 0x38, 0x40, 0x3F,// W
    0x00, 0x63, 0x14, 0x08, 0x14, 0x63,// X
    0x00, 0x07, 0x08, 0x70, 0x08, 0x07,// Y
    0x00, 0x61, 0x51, 0x49, 0x45, 0x43,// Z
    0x00, 0x00, 0x7F, 0x41, 0x41, 0x00,// [
    0x00, 0x55, 0x2A, 0x55, 0x2A, 0x55,// 55
    0x00, 0x00, 0x41, 0x41, 0x7F, 0x00,// ]
    0x00, 0x04, 0x02, 0x01, 0x02, 0x04,// ^
    0x00, 0x40, 0x40, 0x40, 0x40, 0x40,// _
    0x00, 0x00, 0x01, 0x02, 0x04, 0x00,// '
    0x00, 0x20, 0x54, 0x54, 0x54, 0x78,// a
    0x00, 0x7F, 0x48, 0x44, 0x44, 0x38,// b
    0x00, 0x38, 0x44, 0x44, 0x44, 0x20,// c
    0x00, 0x38, 0x44, 0x44, 0x48, 0x7F,// d
    0x00, 0x38, 0x54, 0x54, 0x54, 0x18,// e
    0x00, 0x08, 0x7E, 0x09, 0x01, 0x02,// f
    0x00, 0x18, 0xA4, 0xA4, 0xA4, 0x7C,// g
    0x00, 0x7F, 0x08, 0x04, 0x04, 0x78,// h
    0x00, 0x00, 0x44, 0x7D, 0x40, 0x00,// i
    0x00, 0x40, 0x80, 0x84, 0x7D, 0x00,// j
    0x00, 0x7F, 0x10, 0x28, 0x44, 0x00,// k
    0x00, 0x00, 0x41, 0x7F, 0x40, 0x00,// l
    0x00, 0x7C, 0x04, 0x18, 0x04, 0x78,// m
    0x00, 0x7C, 0x08, 0x04, 0x04, 0x78,// n
    0x00, 0x38, 0x44, 0x44, 0x44, 0x38,// o
    0x00, 0xFC, 0x24, 0x24, 0x24, 0x18,// p
    0x00, 0x18, 0x24, 0x24, 0x18, 0xFC,// q
    0x00, 0x7C, 0x08, 0x04, 0x04, 0x08,// r
    0x00, 0x48, 0x54, 0x54, 0x54, 0x20,// s
    0x00, 0x04, 0x3F, 0x44, 0x40, 0x20,// t
    0x00, 0x3C, 0x40, 0x40, 0x20, 0x7C,// u
    0x00, 0x1C, 0x20, 0x40, 0x20, 0x1C,// v
    0x00, 0x3C, 0x40, 0x30, 0x40, 0x3C,// w
    0x00, 0x44, 0x28, 0x10, 0x28, 0x44,// x
    0x00, 0x1C, 0xA0, 0xA0, 0xA0, 0x7C,// y
    0x00, 0x44, 0x64, 0x54, 0x4C, 0x44,// z
    0x14, 0x14, 0x14, 0x14, 0x14, 0x14,// horiz lines
};

const unsigned char F8X16[]=
{
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//
    0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00,//!
    0x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//"
    0x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00,//#
    0x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00,//$
    0xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00,//%
    0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10,//&
    0x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//'
    0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00,//(
    0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00,//)
    0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00,//*
    0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00,//+
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00,//,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//-
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,//.
    0x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00,///
    0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,//0
    0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//1
    0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,//2
    0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00,//3
    0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00,//4
    0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,//5
    0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00,//6
    0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,//7
    0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00,//8
    0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00,//9
    0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,//:
    0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00,//;
    0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00,//<
    0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00,//=
    0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00,//>
    0x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00,//?
    0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00,//@
    0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,//A
    0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,//B
    0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00,//C
    0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00,//D
    0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00,//E
    0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00,//F
    0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00,//G
    0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20,//H
    0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//I
    0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00,//J
    0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00,//K
    0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00,//L
    0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00,//M
    0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00,//N
    0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00,//O
    0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00,//P
    0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00,//Q
    0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20,//R
    0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00,//S
    0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//T
    0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//U
    0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,//V
    0xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00,//W
    0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20,//X
    0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//Y
    0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00,//Z
    0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00,//[
    0x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00,//\
    0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00,//]
    0x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,//_
    0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//`
    0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,//a
    0x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00,//b
    0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,//c
    0x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20,//d
    0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,//e
    0x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//f
    0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00,//g
    0x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//h
    0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//i
    0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,//j
    0x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00,//k
    0x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//l
    0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,//m
    0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//n
    0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//o
    0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00,//p
    0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80,//q
    0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00,//r
    0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00,//s
    0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,//t
    0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20,//u
    0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00,//v
    0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,//w
    0x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00,//x
    0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00,//y
    0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00,//z
    0x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40,//{
    0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,//|
    0x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00,//}
    0x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//~
};

/* [总字符库]："单片机"*/
char DPJ[][32]=
{
 /*-- ID:0,字符:"单",ASCII编码:B5A5,对应字:宽x高=16x16,画布:宽W=16 高H=16,共32字节*/
 {0x00,0x00,0xf8,0x49,0x4a,0x4c,0x48,0xf8,0x48,0x4c,0x4a,0x49,0xfc,0x08,0x00,0x00},
 {0x10,0x10,0x17,0x12,0x12,0x12,0x12,0xff,0x12,0x12,0x12,0x12,0x13,0x18,0x10,0x00},

 /*-- ID:1,字符:"片",ASCII编码:C6AC,对应字:宽x高=16x16,画布:宽W=16 高H=16,共32字节*/
 {0x00,0x00,0xfe,0x20,0x20,0x20,0x20,0x20,0x3f,0x20,0x20,0x20,0x20,0x30,0x20,0x00},
 {0x80,0x40,0x3f,0x01,0x01,0x01,0x01,0x01,0x01,0xff,0x00,0x00,0x00,0x00,0x00,0x00},

 /*-- ID:2,字符:"机",ASCII编码:BBFA,对应字:宽x高=16x16,画布:宽W=16 高H=16,共32字节*/
 {0x10,0x10,0xd0,0xff,0x90,0x10,0x00,0xfc,0x04,0x04,0x04,0xfe,0x04,0x00,0x00,0x00},
 {0x04,0x03,0x00,0xff,0x80,0x41,0x20,0x1f,0x00,0x00,0x00,0x3f,0x40,0x40,0x70,0x00},
};

#endif

main.c我就不再放出来了，用oled_init和oled_clear函数初始化一下就可以了，注意复用P3.5P3.6引脚的功能。然后在while(1)里直接放相应的显示函数就可以了。