nrf52 供电选择

1.nRF 52820供电

GpioOutputVoltageSetup(UICR_REGOUT0_VOUT_3V0);

#define UICR_REGOUT0_VOUT_1V8 (0UL) /*!< 1.8 V */
#define UICR_REGOUT0_VOUT_2V1 (1UL) /*!< 2.1 V */
#define UICR_REGOUT0_VOUT_2V4 (2UL) /*!< 2.4 V */
#define UICR_REGOUT0_VOUT_2V7 (3UL) /*!< 2.7 V */
#define UICR_REGOUT0_VOUT_3V0 (4UL) /*!< 3.0 V */
#define UICR_REGOUT0_VOUT_3V3 (5UL) /*!< 3.3 V */
#define UICR_REGOUT0_VOUT_DEFAULT (7UL) /*!< Default voltage: 1.8 V */



void GpioOutputVoltageSetup(uint8_t gpioVoltageLevel)
{
    // Configure UICR_REGOUT0 register only if it is set to default value.
    if ((NRF_UICR->REGOUT0 & UICR_REGOUT0_VOUT_Msk) ==
        (UICR_REGOUT0_VOUT_DEFAULT << UICR_REGOUT0_VOUT_Pos))
    {
        NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Wen;
        while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}

        NRF_UICR->REGOUT0 = (NRF_UICR->REGOUT0 & ~((uint32_t)UICR_REGOUT0_VOUT_Msk)) |
                            (gpioVoltageLevel << UICR_REGOUT0_VOUT_Pos);

        NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Ren;
        while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}

        // System reset is needed to update UICR registers.
        NVIC_SystemReset();
    }
}

GpioOutputVoltageSetup(UICR_REGOUT0_VOUT_3V0);

2.NRF52840 VDDH 供电使用方法

/**
 * Function for configuring UICR_REGOUT0 register
 * to set GPIO output voltage to 3.0V.
 */
static void gpio_output_voltage_setup(void)
{
    // Configure UICR_REGOUT0 register only if it is set to default value.
    if ((NRF_UICR->REGOUT0 & UICR_REGOUT0_VOUT_Msk) ==
        (UICR_REGOUT0_VOUT_DEFAULT << UICR_REGOUT0_VOUT_Pos))
    {
        NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Wen;
        while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
 
        NRF_UICR->REGOUT0 = (NRF_UICR->REGOUT0 & ~((uint32_t)UICR_REGOUT0_VOUT_Msk)) |
                            (UICR_REGOUT0_VOUT_2V7 << UICR_REGOUT0_VOUT_Pos);
 
        NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Ren;
        while (NRF_NVMC->READY == NVMC_READY_READY_Busy){}
 
        // System reset is needed to update UICR registers.
        NVIC_SystemReset();
    }