Arduino-nano 指纹门锁

功能：指纹开门，射频遥控开门

硬件：AT301指纹模块，arduino-nano,射频模块，电磁锁，IIC屏幕，
贴片（mos管，电阻，电容，稳压管…)

代码如下：

#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>

#define OLED_RESET -1
#define LOGO16_GLCD_HEIGHT 16 
#define LOGO16_GLCD_WIDTH  16 

void(* resetFunc) (void) = 0;
unsigned char Re_buf[16],counter=0;
unsigned char sign=0;
Adafruit_SSD1306 display(128, 64, &Wire, OLED_RESET);

static const uint8_t PROGMEM Qin_16x16[] = {
0x00,0x40,0x40,0x40,0x27,0xFC,0x20,0x40,0x03,0xF8,0x00,0x40,0xE7,0xFE,0x20,0x00,
0x23,0xF8,0x22,0x08,0x23,0xF8,0x22,0x08,0x2B,0xF8,0x32,0x08,0x22,0x28,0x02,0x10//请
};
static const uint8_t PROGMEM An_16x16[] = {
0x10,0x40,0x10,0x20,0x10,0x20,0x13,0xFE,0xFA,0x02,0x14,0x44,0x10,0x40,0x1B,0xFE,
0x30,0x88,0xD0,0x88,0x11,0x08,0x10,0xD0,0x10,0x20,0x10,0x50,0x50,0x88,0x23,0x04//按
};
static const uint8_t PROGMEM Zhi_16x16[] = {
0x11,0x00,0x11,0x04,0x11,0x38,0x11,0xC0,0xFD,0x02,0x11,0x02,0x10,0xFE,0x14,0x00,
0x19,0xFC,0x31,0x04,0xD1,0x04,0x11,0xFC,0x11,0x04,0x11,0x04,0x51,0xFC,0x21,0x04//指
};
static const uint8_t PROGMEM Wen_16x16[] = {
0x10,0x80,0x10,0x40,0x20,0x40,0x27,0xFC,0x49,0x10,0xF1,0x10,0x11,0x10,0x21,0x10,
0x41,0x10,0xF8,0xA0,0x40,0xA0,0x00,0x40,0x18,0xA0,0xE1,0x10,0x42,0x08,0x0C,0x06//纹
};
static const uint8_t PROGMEM Jin_16x16[] = {
0x00,0x90,0x20,0x90,0x10,0x90,0x13,0xFC,0x00,0x90,0x00,0x90,0xF0,0x90,0x17,0xFE,
0x10,0x90,0x10,0x90,0x11,0x10,0x11,0x10,0x12,0x10,0x28,0x00,0x47,0xFE,0x00,0x00//进
};

static const uint8_t PROGMEM Suo0_16x16[] = {
0x00,0x00,0x00,0x00,0x00,0x01,0xC0,0x00,0x00,0x06,0x30,0x00,0x00,0x18,0x08,0x00,
0x00,0x20,0x04,0x00,0x00,0x20,0x04,0x00,0x00,0x20,0x04,0x00,0x00,0x20,0x04,0x00,
0x00,0x20,0x04,0x00,0x00,0x20,0x04,0x00,0x00,0x20,0x04,0x00,0x03,0xFF,0xFF,0x80,
0x02,0x00,0x00,0x80,0x02,0x00,0x00,0x80,0x02,0x00,0x00,0x80,0x02,0x00,0x00,0x80,
0x02,0x00,0x00,0x80,0x02,0x00,0x00,0x80,0x02,0x00,0x00,0x80,0x02,0x00,0x00,0x80,
0x02,0x00,0x00,0x80,0x02,0x00,0x00,0x80,0x02,0x00,0x00,0x80,0x02,0x00,0x00,0x80,
0x02,0x00,0x00,0x80,0x02,0x00,0x00,0x80,0x02,0x00,0x00,0x80,0x03,0xFF,0xFF,0x80,
0x00,0x00,0x00,0x00//锁0
};
static const uint8_t PROGMEM Suo1_16x16[] = {
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x80,0x00,0x00,0x0C,0x60,0x00,
0x00,0x30,0x10,0x00,0x00,0x40,0x08,0x00,0x00,0x40,0x08,0x00,0x00,0x40,0x00,0x00,
0x00,0x40,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x40,0x00,0x00,
0x07,0xFF,0xFF,0x00,0x04,0x00,0x01,0x00,0x04,0x00,0x01,0x00,0x04,0x00,0x01,0x00,
0x04,0x00,0x01,0x00,0x04,0x00,0x01,0x00,0x04,0x00,0x01,0x00,0x04,0x00,0x01,0x00,
0x04,0x00,0x01,0x00,0x04,0x00,0x01,0x00,0x04,0x00,0x01,0x00,0x04,0x00,0x01,0x00,
0x04,0x00,0x01,0x00,0x04,0x00,0x01,0x00,0x04,0x00,0x01,0x00,0x04,0x00,0x01,0x00,
0x07,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00//锁1
};

void send()//指纹识别
{
  Serial.write(0XEF); 
  Serial.write(0X01);
  Serial.write(0XFF);
  Serial.write(0XFF);
  Serial.write(0XFF);
  Serial.write(0XFF);
  Serial.write(0X01);
  Serial.write(0X00);
  Serial.write(0X08);
  Serial.write(0X32); 
  Serial.write(0X03);
  Serial.write(0XFF);
  Serial.write(0XFF);
  Serial.write(0X01);
  Serial.write(0X01);
  Serial.write(0X02);
  Serial.write(0X3E);
  
 
}
//---------------------------------------------------------------
void serialEvent() {//串口
  while (Serial.available()) {   
    Re_buf[counter]=(unsigned char)Serial.read();
    if(counter==0&&Re_buf[0]!=0xEF&&Re_buf[10]!=0x05) return;      // 检查帧头         
    counter++;       
    if(counter==17)                //接收到数据
    {    
       counter=0;                 //重新赋值，准备下一帧数据的接收 
       sign=1;
    }      
  }
}

//-----------------------------------------------------------
void closedisplay()//关门状态
{
  display.drawBitmap(15,5,Qin_16x16,16,16,WHITE);
  display.display();
  display.drawBitmap(40,5,An_16x16,16,16,WHITE);
  display.display();
  display.drawBitmap(65,5,Zhi_16x16,16,16,WHITE);
  display.display();
  display.drawBitmap(90,5,Wen_16x16,16,16,WHITE);
  display.display();
  display.drawBitmap(46,35,Suo0_16x16,32,32,WHITE);
  display.display(); 
}
//-----------------------------------------------------------
void opendisplay()//开锁成功
{
  display.drawBitmap(45,5,Qin_16x16,16,16,WHITE);
  display.display();
  display.drawBitmap(65,5,Jin_16x16,16,16,WHITE);
  display.display();
  display.drawBitmap(46,35,Suo1_16x16,32,32,WHITE);
  display.display(); 
}

void setup() {
  // put your setup code here, to run once:
  Serial.begin(57600);  
  delay(100);    
  pinMode(4,INPUT);
  pinMode(8,OUTPUT);
  digitalWrite(8,LOW);
  display.begin(SSD1306_SWITCHCAPVCC, 0x3C);
  display.setTextColor(WHITE);//开像素点发光
  display.clearDisplay();//清屏
  display.setTextSize(2); //设置字体大小

}

void loop() {
  // put your main code here, to run repeatedly:
  closedisplay();
  if(digitalRead(4)==HIGH)//射频开门
  {     
        tone(11,600,500);        
        digitalWrite(8,HIGH);
        display.clearDisplay();//清屏
        opendisplay();
        delay(4000);
        display.clearDisplay();//清屏
        digitalWrite(8,LOW);
        resetFunc();//重置函数
  }
     send();
     delay(1200);
     if(sign){
     if(Re_buf[0]==0xEF&&Re_buf[10]==0x05)
     {
      if(Re_buf[9]==0x00)//指纹成功
      {
        tone(11,532,200);
        delay(200);
        tone(11,659,200);
        delay(200);        
        tone(11,1024,200);
        delay(200);        
        digitalWrite(8,HIGH);
        display.clearDisplay();//清屏
        opendisplay();
        delay(4000);
        display.clearDisplay();//清屏
        digitalWrite(8,LOW);
        resetFunc();//重置函数
        
      }
      else{//指纹失败
        tone(11,600,300);
        delay(200);
        tone(11,1500,200);
        display.clearDisplay();//清屏
        display.setCursor(35,20);
        display.println("Error!");
        display.display(); 
        delay(2000);
        display.clearDisplay(); 
        resetFunc(); //重置函数   
      }
      
     }
     
  }

  
}

然后用AD画个板子代替杜邦线连接

这里做了一个小电路设计 用mos管的通断来控制电磁锁，代替传统用继电器的方式

来看看上电的样子：