硬件IIC的OLED代码

已于 2024-03-15 11:04:55 修改
阅读量640 收藏 6
点赞数 7
分类专栏： 单片机STM32 文章标签： stm32 单片机 arm开发 c语言
于 2024-01-24 16:05:23 首次发布
版权声明：本文为博主原创文章，遵循 CC 4.0 BY-SA 版权协议，转载请附上原文出处链接和本声明。
本文链接：https://blog.csdn.net/m0_72065741/article/details/135824791
版权

注意：IIC需要外部上拉

STM32CubeMX配置

在这里插入图片描述

driver_oled.c



#include "ascii_font.c"
#include "string.h"
#include "stm32f1xx_hal.h"

static uint8_t oledBuffer[FRAME_BUFFER_SIZE];

/*
    全屏点亮或者熄灭
*/
#define ENTIRE_DISP_ON()       OLED_WriteCmd(0xA5) 
#define ENTIRE_DISP_OFF()      OLED_WriteCmd(0xA4) 
/*
    阴码显示或者阳码显示
*/
#define DISP_NORMAL()          OLED_WriteCmd(0xA6)  
#define DISP_INVERSE()         OLED_WriteCmd(0xA7)
/*
    打开显示或者关闭显示
*/
#define DISP_ON()              OLED_WriteCmd(0xAF) 
#define DISP_OFF()             OLED_WriteCmd(0xAE) 

/* 2. 滚动命令功能函数 */
typedef enum
{
    H_RIGHT     = 0x26,
    H_LEFT      = 0x27,
}H_SCROLL_DIR;  // 水平滚动方向


typedef enum
{
    HV_RIGHT    = 0x29,
    HV_LEFT     = 0x2A,
}HV_SCROLL_DIR;     // 水平和垂直滚动的方向


/* 
    开始或者停止滚动
*/
#define SCROLL_ON()             OLED_WriteCmd(0x2F)
#define SCROLL_OFF()            OLED_WriteCmd(0x2E)


/* 3. 地址设置功能函数 */
typedef enum
{
    H_ADDR_MODE     = 0,    // 水平地址模式
    V_ADDR_MODE     = 1,    // 垂直地址模式
    PAGE_ADDR_MODE  = 2,    // 页地址模式
}MEM_MODE;  // 内存地址模式


/*
    行地址翻转或者不翻转
*/
#define OLED_SEG_REMAP()        OLED_WriteCmd(0xA1)
#define OLED_SEG_NOREMAP()      OLED_WriteCmd(0xA0)


/*
    COM引脚扫描方向正常扫描或者逆扫描
*/
#define OLED_SCAN_NORMAL()      OLED_WriteCmd(0xC0)
#define OLED_SCAN_REMAP()       OLED_WriteCmd(0xC8)


typedef enum
{
    COM_PIN_SEQ     = 0,
    COM_PIN_ALT     = 1,
}COM_PINS_MODE; // COM引脚属性
typedef enum
{
    COM_NOREMAP     = 0,
    COM_REMAP       = 1,
}COM_REMAP_STATE;   // COM引脚翻转

    
typedef enum
{
    LEVEL_0     = 0x00,
    LEVEL_1     = 0x20,
    LEVEL_2     = 0x30,
}VCOMH_LEVEL;   // 电压等级

/* 6. 电荷碰撞功能函数 */
typedef enum
{
    PUMP_DISABLE    = 0,
    PUMP_ENABLE     = 1,
}CHARGE_PUMP_STATE; // 打开或者关闭电荷泵


#define OELD_I2C_ADDR 0x78
#define OLED_TIMEOUT  500
extern I2C_HandleTypeDef hi2c1;
static I2C_HandleTypeDef *g_pHI2COLED = &hi2c1;

/*
 *  函数名：OLED_WriteCmd
 *  功能描述：I2C发送命令给OLED
 *  输入参数：cmd-发送给OLED的命令
 *  输出参数：无
 *  返回值：0-成功, 其他值失败
 */
static int OLED_WriteCmd(uint8_t cmd)
{
    uint8_t tmpbuf[2];

    tmpbuf[0] = 0;
    tmpbuf[1] = cmd;
    
    return HAL_I2C_Master_Transmit(g_pHI2COLED, OELD_I2C_ADDR, tmpbuf, 2, OLED_TIMEOUT);
}

/*
 *  函数名：OLED_WriteData
 *  功能描述：I2C发送命令给OLED
 *  输入参数：data-发送给OLED的写入GDRAM的数据
 *  输出参数：无
 *  返回值：0-成功, 其他值失败
 */
static int OLED_WriteData(uint8_t data)
{
    uint8_t tmpbuf[2];

    tmpbuf[0] = 0x40;
    tmpbuf[1] = data;
    
    return HAL_I2C_Master_Transmit(g_pHI2COLED, OELD_I2C_ADDR, tmpbuf, 2, OLED_TIMEOUT);
}

/*
 *  函数名：OLED_WriteNBytes
 *  功能描述：连续发送N个写入显存的数据
 *  输入参数：buf         - 数据buffer
 *            length - 数据个数
 *  输出参数：无
 *  返回值：0-成功, 其他值失败
 */
static int OLED_WriteNBytes(uint8_t *buf, uint16_t length)
{
    return HAL_I2C_Mem_Write(g_pHI2COLED, OELD_I2C_ADDR, 0x40, 1, buf, length, OLED_TIMEOUT);
}

/************** 1. 基础命令功能函数 **************/
/*
 *  函数名：OLED_SetContrastValue
 *  功能描述：设置OLED的对比度：发送命令0x81--->发送对比度值
 *  输入参数：value --> 对比度值，范围0~255
 *  输出参数：无
 *  返回值：无
*/
static void OLED_SetContrastValue(uint8_t value)
{
    OLED_WriteCmd(0x81);
    OLED_WriteCmd(value);
}

/************** 2. 滚动命令功能函数 **************/
/*
 *  函数名：OLED_H_Scroll
 *  功能描述：让指定页的像素朝着设置的方向按设置的频率水平滚动
 *  输入参数：dir--->滚动方向：朝左或者朝右
 *            start--->起始页
 *            fr_time--->滚动间隔时间，每隔这么多帧水平偏移一列滚动
 *            end--->结束页
 *  输出参数：无
 *  返回值：无
*/
static void OLED_H_Scroll(H_SCROLL_DIR dir, uint8_t start, uint8_t fr_time, uint8_t end)
{
    if((dir != H_RIGHT) && (dir != H_LEFT))     return;
    if((start>0x07) || (fr_time>0x07) || (end>0x07))    return;
    OLED_WriteCmd(dir);
    OLED_WriteCmd(0x00);
    OLED_WriteCmd(start);
    OLED_WriteCmd(fr_time);
    OLED_WriteCmd(end);
    OLED_WriteCmd(0x00);
    OLED_WriteCmd(0xFF);
}

/*
 *  函数名：OLED_HV_Scroll
 *  功能描述：让指定页的像素朝着设置的方向按设置的频率水平滚动且会将像素的行地址进行偏移offset这么多个单位
 *  输入参数：dir--->滚动方向：朝左或者朝右
 *            start--->起始页
 *            fr_time--->滚动间隔时间，每隔这么多帧水平偏移一列滚动
 *            end--->结束页
 *            offset--->行偏移单位
 *  输出参数：无
 *  返回值：无
*/
static void OLED_HV_Scroll(HV_SCROLL_DIR dir, uint8_t start, uint8_t fr_time, uint8_t end, uint8_t offset)
{
    if((dir != HV_RIGHT) && (dir != HV_LEFT))     return;
    if((start>0x07) || (fr_time>0x07) || (end>0x07) || (offset>0x3F))    return;
    OLED_WriteCmd(dir);
    OLED_WriteCmd(0x00);
    OLED_WriteCmd(start);
    OLED_WriteCmd(fr_time);
    OLED_WriteCmd(end);
    OLED_WriteCmd(offset);
}

/*
 *  函数名：OLED_SetVScrollArea
 *  功能描述：设置OLED像素垂直滚动的区域
 *  输入参数：area-->顶行区域
 *            row_num--->滚动的行区域
 *  输出参数：无
 *  返回值：无
*/
static void OLED_SetVScrollArea(uint8_t area, uint8_t row_num)
{
    if((area>0x3F) || (row_num>0x7F))       return;
    OLED_WriteCmd(0xA3);
    OLED_WriteCmd(area);
    OLED_WriteCmd(row_num);
}

/************** 3. 地址设置功能函数 **************/
static MEM_MODE mem_mode = PAGE_ADDR_MODE;  // 静态局部变量，保存OLED的地址模式的

/*
 *  函数名：OLED_SetColAddr_PAGE
 *  功能描述：设置OLED在页地址模式下的显示起始行地址
 *  输入参数：addr-->起始行地址
 *  输出参数：无
 *  返回值：无
*/
static void OLED_SetColAddr_PAGE(uint8_t addr)
{
    if(mem_mode != PAGE_ADDR_MODE)  return;
    if(addr > 0x7F)   return;
    OLED_WriteCmd(0x00 + (addr & 0x0F));
    OLED_WriteCmd(0x10 + (addr>>4));
}

/*
 *  函数名：OLED_SetMemAddrMode
 *  功能描述：设置OLED的地址模式
 *  输入参数：mode-->地址模式：页地址模式、水平地址模式、垂直地址模式
 *  输出参数：无
 *  返回值：无
*/
static void OLED_SetMemAddrMode(MEM_MODE mode)
{
    if((mode != H_ADDR_MODE) && (mode != V_ADDR_MODE) && (mode != PAGE_ADDR_MODE))      return;
    OLED_WriteCmd(0x20);
    OLED_WriteCmd(mode);
    mem_mode = mode;
}

/*
 *  函数名：OLED_SetColAddr_HV
 *  功能描述：设置OLED在水平地址模式或垂直地址模式下像素显示的起始行地址和结束行地址
 *  输入参数：start-->起始行地址
 *            end --->结束行地址
 *  输出参数：无
 *  返回值：无
*/
static void OLED_SetColAddr_HV(uint8_t start, uint8_t end)
{
    if(mem_mode == PAGE_ADDR_MODE)      return;
    if((start > 127) || (end > 127))    return;
    OLED_WriteCmd(0x21);
    OLED_WriteCmd(start);
    OLED_WriteCmd(end);
}

/*
 *  函数名：OLED_SetPageAddr_HV
 *  功能描述：设置OLED在水平地址模式或垂直地址模式下像素显示的起始页地址和结束页地址
 *  输入参数：start-->起始页地址
 *            end --->结束页地址
 *  输出参数：无
 *  返回值：无
*/
static void OLED_SetPageAddr_HV(uint8_t start, uint8_t end)
{
    if(mem_mode == PAGE_ADDR_MODE)      return;
    if((start > 7) || (end > 7))        return; 
    OLED_WriteCmd(0x22);
    OLED_WriteCmd(start);
    OLED_WriteCmd(end);
}

/*
 *  函数名：OLED_SetPageAddr_PAGE
 *  功能描述：设置OLED在页地址模式下的显示起始页地址
 *  输入参数：addr-->起始页地址
 *  输出参数：无
 *  返回值：无
*/
static void OLED_SetPageAddr_PAGE(uint8_t addr)
{
    if(mem_mode != PAGE_ADDR_MODE)  return;
    if(addr > 7)   return;
    OLED_WriteCmd(0xB0 + addr);
}

/************** 4. 硬件配置功能函数 **************/
/*
 *  函数名：OLED_SetDispStartLine
 *  功能描述：设置OLED从第line行开始显示，即将默认的0行偏移至line那一行
 *  输入参数：line-->显示的起始行
 *  输出参数：无
 *  返回值：无
*/
static void OLED_SetDispStartLine(uint8_t line)
{
    if(line > 63)       return;
    OLED_WriteCmd(0x40 + line);
}

/*
 *  函数名：OLED_SetMuxRatio
 *  功能描述：设置OLED复用率
 *  输入参数：ratio-->复用率值
 *  输出参数：无
 *  返回值：无
*/
static void OLED_SetMuxRatio(uint8_t ratio)
{
    if((ratio < 15) || (ratio > 63))      return;
    OLED_WriteCmd(0xA8);
    OLED_WriteCmd(ratio);
}

/*
 *  函数名：OLED_SetDispOffset
 *  功能描述：设置OLED的COM引脚偏移值
 *  输入参数：offset-->COM偏移值
 *  输出参数：无
 *  返回值：无
*/
static void OLED_SetDispOffset(uint8_t offset)
{
    if(offset > 63)     return;
    OLED_WriteCmd(0xD3);
    OLED_WriteCmd(offset);
}

/*
 *  函数名：OLED_SetComConfig
 *  功能描述：设置OLED的COM引脚属性
 *  输入参数：mode-->COM引脚模式是连续的还是可选择的
 *            state-->COM引脚翻转与否
 *  输出参数：无
 *  返回值：无
*/
static void OLED_SetComConfig(COM_PINS_MODE mode, COM_REMAP_STATE state)
{
    if((mode != COM_PIN_SEQ) && (mode != COM_PIN_ALT))      return;
    if((state != COM_NOREMAP) && (state != COM_REMAP))      return;
    
    OLED_WriteCmd(0xDA);
    OLED_WriteCmd(0x02 + (mode << 4) + (state << 5));
}

/************** 5. 时间设置功能函数 **************/
/*
 *  函数名：OLED_SetDCLK_Freq
 *  功能描述：设置OLED的扫描周期和晶振频率
 *  输入参数：div-->时钟分频系数
 *            freq-->晶振频率
 *  输出参数：无
 *  返回值：无
*/
static void OLED_SetDCLK_Freq(uint8_t div, uint8_t freq)
{
    if((div>0x0F) || (freq>0x0F))       return;
    OLED_WriteCmd(0xD5);
    OLED_WriteCmd(div + (freq<<4));
}

/*
 *  函数名：OLED_SetPreChargePeriod
 *  功能描述：设置OLED的预充电周期
 *  输入参数：phase1-->预充电阶段1时间
 *            phase2-->预充电阶段2时间
 *  输出参数：无
 *  返回值：无
*/
static void OLED_SetPreChargePeriod(uint8_t phase1, uint8_t phase2)
{
    if((phase1>0x0F) || (phase2>0x0F))       return;
    OLED_WriteCmd(0xD9);
    OLED_WriteCmd(phase1 + (phase2<<4));    
}

/*
 *  函数名：OLED_SetVcomhLevel
 *  功能描述：设置OLED的电压等级
 *  输入参数：level-->电压等级
 *  输出参数：无
 *  返回值：无
*/
static void OLED_SetVcomhLevel(VCOMH_LEVEL level)
{
    if((level != LEVEL_0) && (level != LEVEL_1) && (level != LEVEL_2))      return;
    OLED_WriteCmd(0xDB);
    OLED_WriteCmd(level);
}

/************** 6. 电荷碰撞功能函数 **************/
/*
 *  函数名：OLED_SetChargePump
 *  功能描述：打开或关闭OLED的电荷泵
 *  输入参数：state-->电荷泵打开或关闭
 *  输出参数：无
 *  返回值：无
*/
static void OLED_SetChargePump(CHARGE_PUMP_STATE state)
{
    if((state != PUMP_DISABLE) && (state != PUMP_ENABLE))   return;
    OLED_WriteCmd(0x8D);
    OLED_WriteCmd((state<<2) + 0x10);
}

/************** 7. 初始化函数 **************/
/*
 *  函数名：OLED_Init
 *  功能描述：初始化OLED
 *  输入参数：无
 *  输出参数：无
 *  返回值：无
 */
void OLED_Init(void)
{   
    /*
     * 前提: 已经初始化的I2C通道
     * 本工程里已经: 
     *    使用MX_I2C1_Init初始化I2C通道
     *    使用HAL_I2C_MspInit初始化I2C引脚
     */
    delay_us(50);							//防止硬件速度过快导致初始化错误
    OLED_SetMemAddrMode(PAGE_ADDR_MODE);    // 0. 设置地址模式
    OLED_SetMuxRatio(0x3F);                 // 1. 设置多路复用率
    OLED_SetDispOffset(0x00);               // 2. 设置显示的偏移值
    OLED_SetDispStartLine(0x00);            // 3. 设置起始行
    OLED_SEG_REMAP();                       // 4. 行翻转
    OLED_SCAN_REMAP();                      // 5. 正常扫描
    OLED_SetComConfig(COM_PIN_SEQ, COM_NOREMAP);          // 6. COM 引脚设置
    OLED_SetContrastValue(0x7F);            // 7. 设置对比度
    ENTIRE_DISP_OFF();                      // 8. 全屏点亮/熄灭
    DISP_NORMAL();                          // 9. 显示模式
    OLED_SetDCLK_Freq(0x00, 0x08);          // 10. 设置分频系数和频率增值
    OLED_SetChargePump(PUMP_ENABLE);        // 11. 使能电荷碰撞
    
    OLED_SetComConfig(COM_PIN_ALT, COM_NOREMAP);
    OLED_Clear();
    DISP_ON();
}

/************** 8. 基本驱动功能函数 **************/
/*
 *  函数名：OLED_SetPosition
 *  功能描述：设置像素显示的起始页和起始列地址
 *  输入参数：page-->页地址模式下的起始页地址
 *            col-->页地址模式下的起始行地址
 *  输出参数：无
 *  返回值：无
*/
void OLED_SetPosition(uint8_t page, uint8_t col)
{
    OLED_SetPageAddr_PAGE(page);
    OLED_SetColAddr_PAGE(col);
}

/*
 *  函数名：OLED_Clear
 *  功能描述：清屏函数
 *  输入参数：无
 *  输出参数：无
 *  返回值：无
*/
void OLED_Clear(void)
{
    uint8_t i = 0;
    uint8_t buf[128] = {0};
    
    for(i=0; i<8; i++)
    {
        OLED_SetPosition(i, 0);
        OLED_WriteNBytes(&buf[0], 128);
    }
}

/*
 *  函数名：OLED_PutChar
 *  功能描述：显示一个字符
 *  输入参数：x --> x坐标(0~15)
 *            y --> y坐标(0~7)
 *            c -->   显示的字符
 *  输出参数：无
 *  返回值：无
 */
void OLED_PutChar(uint8_t x, uint8_t y, char c)
{
    uint8_t page = y;
    uint8_t col  = x*8;
    
    if (y > 7 || x > 15)
        return;
    
    OLED_SetPosition(page, col);
    OLED_WriteNBytes((uint8_t*)&ascii_font[c][0], 8);
    
    OLED_SetPosition(page + 1, col);
    OLED_WriteNBytes((uint8_t*)&ascii_font[c][8], 8);
}

/*
 *  函数名：OLED_PrintString
 *  功能描述：显示一个字符串
 *  输入参数：x --> x坐标(0~15)
 *            y --> y坐标(0~7)
 *            str -->   显示的字符串
 *  输出参数：无
 *  返回值：打印了多少个字符
 */
int OLED_PrintString(uint8_t x, uint8_t y, const char *str)
{   
    int i = 0;
    while (str[i])
    {
        OLED_PutChar(x, y, str[i]);
        x++;
        if(x > 15)
        {
            x  = 0;
            y += 2;
        }
                
        i++;
    }
    return i;
}

void OLED_PrintChinese(uint8_t x, uint8_t y)
{   
	extern uint8_t g_chinese_fonts[3][32];

	uint8_t page = y;
	uint8_t col  = x*8;
	
	if (y > 7 || x > 15)
			return;
	
	int i;
	for (i = 0; i < sizeof(g_chinese_fonts)/sizeof(g_chinese_fonts[0]); i++)
	{
		/* 设置位置: page,col */
    OLED_SetPosition(page, col);

		/* 发送16字节数据(汉字的上半部) */
    OLED_WriteNBytes((uint8_t*)&g_chinese_fonts[i][0], 16);

		/* 设置位置: page+1,col */
    OLED_SetPosition(page+1, col);
		
		/* 发送16字节数据(汉字的下半部) */
    OLED_WriteNBytes((uint8_t*)&g_chinese_fonts[i][16], 16);

		/* 更新下一个字符的位置:page不变,col+=16 */	
		col += 16;
	}
}


/*
 *  函数名：OLED_ClearLine
 *  功能描述：清除一行
 *  输入参数：x - 从这里开始
 *            y - 清除这行
 *  输出参数：无
 *  返回值：无
 */
void OLED_ClearLine(uint8_t x, uint8_t y)
{
    for (;x < 16; x++)
    {
        OLED_PutChar(x, y, ' ');
    }
}

/*
 *  OLED_PrintHex
 *  功能描述：以16进制显示数值
 *  输入参数：x - x坐标(0~15)
 *            y - y坐标(0~7)
 *            val -   显示的数据
 *            pre -   非零时显示"0x"前缀
 *  输出参数：无
 *  返回值：打印了多少个字符
 */
int OLED_PrintHex(uint8_t x, uint8_t y, uint32_t val, uint8_t pre)
{
    uint8_t hex_tab[]={'0','1','2','3','4','5','6','7',\
                             '8','9','a','b','c','d','e','f'};
	int i, j;
	char arr[11];

	/* 提取数据 */
    arr[0] = '0';
    arr[1] = 'x';
    arr[10] = '\0';

    j = 2;
	for (i = 7; i >= 0; i--)
	{
        arr[j] = hex_tab[(val >> (i*4)) & 0xf];
        if ((j != 2) || (arr[j] != '0'))
        {
            j++;
        }        
	}
    if (j == 2)
        j++;
    arr[j] = '\0';

    if (pre)
    {
        OLED_PrintString(x, y, arr);
        return j;
    }
    else
    {
        OLED_PrintString(x, y, arr+2);
        return j - 2;
    }
}


/*
 *  OLED_PrintSignedVal
 *  功能描述：以10进制显示一个数值
 *  输入参数：x --> x坐标(0~15)
 *            y --> y坐标(0~7)
 *            val -->   显示的数据
 *  输出参数：无
 *  返回值：打印了多少个字符
*/
int OLED_PrintSignedVal(uint8_t x, uint8_t y, int32_t val)
{
    char str[16];
    char revert_str[16];
    int i = 0, j = 0;
    int mod;

    if (val < 0)
    {
        str[i++] = '-';
        val = 0 - val;
    }
    else if (val == 0)
    {
        str[i++] = '0';
    }

    while (val)
    {
        mod = val % 10;
        revert_str[j++] = mod + '0';
        val = val / 10;
    }

    while (j)
    {
        str[i++] = revert_str[j-1];
        j--;
    } 
    
    str[i] = '\0';
    OLED_PrintString(x, y, str);
    return i;
}

/**********************************************************************
 *  OLED_GetFrameBuffer
 *  功能描述：获得OLED的Framebuffer
 *  输入参数：无
 *  输出参数：pXres/pYres/pBpp - 用来保存分辨率、bpp
 *  返回值：Framebuffer首地址
 * -----------------------------------------------
 * 2023/08/31        V1.0     韦东山       创建
 ***********************************************************************/
void * OLED_GetFrameBuffer(uint32_t *pXres, uint32_t *pYres, uint32_t *pBpp)
{
    *pXres = FRAME_WIDTH;
    *pYres = FRAME_HEIGHT;
    *pBpp  = 1;
    return oledBuffer;
}

/**********************************************************************
 *  OLED_Flush
 *  功能描述：把Framebuffer的数据全部刷新到OLED
 *  输入参数：无
 *  输出参数：无
 *  返回值：无
 * -----------------------------------------------
 * 2023/08/31        V1.0     韦东山       创建
 ***********************************************************************/
void OLED_Flush(void)
{
      uint8_t i;
      for(i=0;i<8;i++)
      {
         OLED_WriteCmd(0xb0+i); //设置行起始地址
         OLED_WriteCmd(0x00);   //设置低列起始地址
         OLED_WriteCmd(0x10);   //设置高列起始地址
         //for(n=0;n<128;n++)
         //  OLED_WriteData(oledBuffer[128*i+n]);
         OLED_WriteNBytes(&oledBuffer[128*i], 128);
    }
}

/**********************************************************************
 *  OLED_FlushRegion
 *  功能描述：刷新OLED的区域
 *  输入参数：col     - OLED的列,取值范围0~127
 *            row - OLED的行,取值范围0~63
 *            width - 宽度
 *            heigh - 高度,必须是8的整数倍
 *  输出参数：无
 *  返回值：无
 * -----------------------------------------------
 * 2023/08/31        V1.0     韦东山       创建
 ***********************************************************************/
void OLED_FlushRegion(int col, int row, int width, int heigh)
{
#if 0    
      uint8_t i;
      uint8_t page = row / 8;
      
      for (i = 0; i < heigh/8; i++)
      {
         OLED_SetPosition(page+i, col);
         OLED_WriteNBytes(&oledBuffer[col + (page + i) * FRAME_WIDTH], width);
        }
#else
    uint8_t i;
    uint8_t page = row / 8;
    uint8_t page_cnt = ((row % 8) + heigh +7)/8;
    
    for (i = 0; i < page_cnt; i++)
    {
        if (page+i < 8)
        {
           OLED_SetPosition(page+i, col);
           OLED_WriteNBytes(&oledBuffer[col + (page + i) * FRAME_WIDTH], width);
        }
      }

#endif
}


/**********************************************************************
 *  OLED_ClearFrameBuffer
 *  功能描述：把Framebuffer的数据全部清零
 *  输入参数：无
 *  输出参数：无
 *  返回值：无
 * -----------------------------------------------
 * 2023/08/31        V1.0     韦东山       创建
 ***********************************************************************/
void OLED_ClearFrameBuffer(void)
{
    memset(oledBuffer, 0, sizeof(oledBuffer));
}


/**********************************************************************
 * 函数名称： OLED_Test
 * 功能描述： OLED测试程序
 * 输入参数： 无
 * 输出参数： 无
 *            无
 * 返 回 值： 0 - 成功, 其他值 - 失败
 * 修改日期        版本号     修改人        修改内容
 * -----------------------------------------------
 * 2023/08/03        V1.0     韦东山       创建
 ***********************************************************************/
void OLED_Test(void)
{
	int cnt = 0;
    OLED_Init();
	// 清屏
	OLED_Clear();
	
	char *str1 = "100ask";
	char *str2 = ".net";
	int len;
    
	while (1)
	{
		// 在(0, 0)打印'A'
		OLED_PutChar(0, 0, 'A');
		// 在(1, 0)打印'Y'
		OLED_PutChar(1, 0, 'Y');
		// 在第0列第2页打印一个字符串"Hello World!"
		OLED_PrintString(0, 2, "Hello World!");
		
		len = OLED_PrintString(0, 4, str1);
		len += OLED_PrintString(len, 4, str2);
		OLED_PrintSignedVal(len+1, 4, cnt);
		cnt++;
		HAL_Delay(1000);
	}
}

driver_oled.h



#ifndef __DRIVER_OLED_H
#define __DRIVER_OLED_H

#include <stdint.h>

#define FRAME_WIDTH			128
#define FRAME_HEIGHT		64
#define FRAME_BUFFER_SIZE	((FRAME_WIDTH * FRAME_HEIGHT) / 8)


/*
 *  函数名：OLED_Init
 *  功能描述：初始化OLED
 *  输入参数：无
 *  输出参数：无
 *  返回值：无
 */
void OLED_Init(void);

/*
 *  函数名：OLED_SetPosition
 *  功能描述：设置像素显示的起始页和起始列地址
 *  输入参数：page-->页地址模式下的起始页地址
 *            col-->页地址模式下的起始行地址
 *  输出参数：无
 *  返回值：无
*/
void OLED_SetPosition(uint8_t page, uint8_t col);

/*
 *  函数名：OLED_Clear
 *  功能描述：清屏函数
 *  输入参数：无
 *  输出参数：无
 *  返回值：无
*/
void OLED_Clear(void);

/*
 *  函数名：OLED_PutChar
 *  功能描述：显示一个字符
 *  输入参数：x --> x坐标(0~15)
 *            y --> y坐标(0~7)
 *            c -->   显示的字符
 *  输出参数：无
 *  返回值：无
*/
void OLED_PutChar(uint8_t x, uint8_t y, char c);


/*
 *  函数名：OLED_PrintString
 *  功能描述：显示一个字符串
 *  输入参数：x --> x坐标(0~15)
 *            y --> y坐标(0~7)
 *            str -->   显示的字符串
 *  输出参数：无
 *  返回值：打印了多少个字符
 */
int OLED_PrintString(uint8_t x, uint8_t y, const char *str);


/*
 *  函数名：OLED_ClearLine
 *  功能描述：清除一行
 *  输入参数：x - 从这里开始
 *            y - 清除这行
 *  输出参数：无
 *  返回值：无
 */
void OLED_ClearLine(uint8_t x, uint8_t y);

/*
 *  OLED_PrintHex
 *  功能描述：以16进制显示数值
 *  输入参数：x - x坐标(0~15)
 *            y - y坐标(0~7)
 *            val -   显示的数据
 *            pre -   非零时显示"0x"前缀
 *  输出参数：无
 *  返回值：打印了多少个字符
 */
int OLED_PrintHex(uint8_t x, uint8_t y, uint32_t val, uint8_t pre);

/**********************************************************************
 *  OLED_PrintSignedVal
 *  功能描述：以10进制显示一个数值
 *  输入参数：x --> x坐标(0~15)
 *            y --> y坐标(0~7)
 *            val -->   显示的数据
 *  输出参数：无
 *  返回值：打印了多少个字符
 ***********************************************************************/
int OLED_PrintSignedVal(uint8_t x, uint8_t y, int32_t val);

/**********************************************************************
 *  OLED_GetFrameBuffer
 *  功能描述：获得OLED的Framebuffer
 *  输入参数：无
 *  输出参数：pXres/pYres/pBpp - 用来保存分辨率、bpp
 *  返回值：Framebuffer首地址
 * -----------------------------------------------
 * 2023/08/31        V1.0     韦东山       创建
 ***********************************************************************/
void * OLED_GetFrameBuffer(uint32_t *pXres, uint32_t *pYres, uint32_t *pBpp);

/**********************************************************************
 *  OLED_Flush
 *  功能描述：把Framebuffer的数据全部刷新到OLED
 *  输入参数：无
 *  输出参数：无
 *  返回值：无
 * -----------------------------------------------
 * 2023/08/31        V1.0     韦东山       创建
 ***********************************************************************/
void OLED_Flush(void);

/**********************************************************************
 *  OLED_ClearFrameBuffer
 *  功能描述：把Framebuffer的数据全部清零
 *  输入参数：无
 *  输出参数：无
 *  返回值：无
 * -----------------------------------------------
 * 2023/08/31        V1.0     韦东山       创建
 ***********************************************************************/
void OLED_ClearFrameBuffer(void);

/**********************************************************************
 * 函数名称： OLED_Test
 * 功能描述： OLED测试程序
 * 输入参数： 无
 * 输出参数： 无
 *            无
 * 返 回 值： 0 - 成功, 其他值 - 失败
 * 修改日期        版本号     修改人        修改内容
 * -----------------------------------------------
 * 2023/08/03        V1.0     韦东山       创建
 ***********************************************************************/
void OLED_Test(void);

#endif /* __DRIVER_OLED_H */

ascii_font.c

#include <stdint.h>
#include "driver_oled.h"
const uint8_t ascii_font[128][16] = {
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",1*/

{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"",2*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",3*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",4*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",5*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",6*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",7*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",8*/

{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"	",9*/

{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",10*/

{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",11*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",12*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",13*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",14*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",15*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",16*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",17*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",18*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",19*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",20*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",21*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",22*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",23*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",24*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",25*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",26*/

{0x00,0xFE,0x02,0x02,0x02,0x02,0x02,0x02,0x00,0x3F,0x20,0x20,0x20,0x20,0x20,0x20},/*"",27*/

{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"",28*/

{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"",29*/

{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"",30*/

{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"",31*/

{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",32*/

{0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x00,0x00,0x00,0x00},/*"!",33*/

{0x00,0x10,0x0C,0x02,0x10,0x0C,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*""",34*/

{0x00,0x40,0xC0,0x78,0x40,0xC0,0x78,0x00,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x00},/*"#",35*/

{0x00,0x70,0x88,0x88,0xFC,0x08,0x30,0x00,0x00,0x18,0x20,0x20,0xFF,0x21,0x1E,0x00},/*"$",36*/

{0xF0,0x08,0xF0,0x80,0x60,0x18,0x00,0x00,0x00,0x31,0x0C,0x03,0x1E,0x21,0x1E,0x00},/*"%",37*/

{0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x2C,0x19,0x27,0x21,0x10},/*"&",38*/

{0x00,0x12,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",39*/

{0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00},/*"(",40*/

{0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00},/*")",41*/

{0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00},/*"*",42*/

{0x00,0x00,0x00,0x00,0xE0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x0F,0x01,0x01,0x01},/*"+",43*/

{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x90,0x70,0x00,0x00,0x00,0x00,0x00},/*",",44*/

{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x00},/*"-",45*/

{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00},/*".",46*/

{0x00,0x00,0x00,0x00,0xC0,0x38,0x04,0x00,0x00,0x60,0x18,0x07,0x00,0x00,0x00,0x00},/*"/",47*/

{0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00},/*"0",48*/

{0x00,0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00},/*"1",49*/

{0x00,0x70,0x08,0x08,0x08,0x08,0xF0,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00},/*"2",50*/

{0x00,0x30,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x18,0x20,0x21,0x21,0x22,0x1C,0x00},/*"3",51*/

{0x00,0x00,0x80,0x40,0x30,0xF8,0x00,0x00,0x00,0x06,0x05,0x24,0x24,0x3F,0x24,0x24},/*"4",52*/

{0x00,0xF8,0x88,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x20,0x20,0x20,0x11,0x0E,0x00},/*"5",53*/

{0x00,0xE0,0x10,0x88,0x88,0x90,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x20,0x1F,0x00},/*"6",54*/

{0x00,0x18,0x08,0x08,0x88,0x68,0x18,0x00,0x00,0x00,0x00,0x3E,0x01,0x00,0x00,0x00},/*"7",55*/

{0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00},/*"8",56*/

{0x00,0xF0,0x08,0x08,0x08,0x10,0xE0,0x00,0x00,0x01,0x12,0x22,0x22,0x11,0x0F,0x00},/*"9",57*/

{0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00},/*":",58*/

{0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0x00,0x00,0x00,0x00},/*";",59*/

{0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00},/*"<",60*/

{0x00,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x00,0x02,0x02,0x02,0x02,0x02,0x02,0x00},/*"=",61*/

{0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00},/*">",62*/

{0x00,0x70,0x48,0x08,0x08,0x88,0x70,0x00,0x00,0x00,0x00,0x30,0x37,0x00,0x00,0x00},/*"?",63*/

{0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x28,0x2F,0x28,0x17,0x00},/*"@",64*/

{0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20},/*"A",65*/

{0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00},/*"B",66*/

{0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00},/*"C",67*/

{0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00},/*"D",68*/

{0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00},/*"E",69*/

{0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00},/*"F",70*/

{0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00},/*"G",71*/

{0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20},/*"H",72*/

{0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"I",73*/

{0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00},/*"J",74*/

{0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00},/*"K",75*/

{0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00},/*"L",76*/

{0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x01,0x3E,0x01,0x3F,0x20,0x00},/*"M",77*/

{0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00},/*"N",78*/

{0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00},/*"O",79*/

{0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00},/*"P",80*/

{0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x28,0x28,0x30,0x50,0x4F,0x00},/*"Q",81*/

{0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20},/*"R",82*/

{0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00},/*"S",83*/

{0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00},/*"T",84*/

{0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00},/*"U",85*/

{0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00},/*"V",86*/

{0x08,0xF8,0x00,0xF8,0x00,0xF8,0x08,0x00,0x00,0x03,0x3E,0x01,0x3E,0x03,0x00,0x00},/*"W",87*/

{0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20},/*"X",88*/

{0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00},/*"Y",89*/

{0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00},/*"Z",90*/

{0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00},/*"[",91*/

{0x00,0x04,0x38,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00},/*"\",92*/

{0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00},/*"]",93*/

{0x00,0x00,0x04,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",94*/

{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80},/*"_",95*/

{0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",96*/

{0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x19,0x24,0x24,0x12,0x3F,0x20,0x00},/*"a",97*/

{0x10,0xF0,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00},/*"b",98*/

{0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00},/*"c",99*/

{0x00,0x00,0x80,0x80,0x80,0x90,0xF0,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20},/*"d",100*/

{0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x24,0x24,0x24,0x24,0x17,0x00},/*"e",101*/

{0x00,0x80,0x80,0xE0,0x90,0x90,0x20,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"f",102*/

{0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00},/*"g",103*/

{0x10,0xF0,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20},/*"h",104*/

{0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"i",105*/

{0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00},/*"j",106*/

{0x10,0xF0,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x06,0x29,0x30,0x20,0x00},/*"k",107*/

{0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"l",108*/

{0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F},/*"m",109*/

{0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20},/*"n",110*/

{0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00},/*"o",111*/

{0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0x91,0x20,0x20,0x11,0x0E,0x00},/*"p",112*/

{0x00,0x00,0x00,0x80,0x80,0x00,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0x91,0xFF,0x80},/*"q",113*/

{0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00},/*"r",114*/

{0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00},/*"s",115*/

{0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x10,0x00},/*"t",116*/

{0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20},/*"u",117*/

{0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x03,0x0C,0x30,0x0C,0x03,0x00,0x00},/*"v",118*/

{0x80,0x80,0x00,0x80,0x80,0x00,0x80,0x80,0x01,0x0E,0x30,0x0C,0x07,0x38,0x06,0x01},/*"w",119*/

{0x00,0x80,0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x20,0x31,0x0E,0x2E,0x31,0x20,0x00},/*"x",120*/

{0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x81,0x86,0x78,0x18,0x06,0x01,0x00},/*"y",121*/

{0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00},/*"z",122*/

{0x00,0x00,0x00,0x00,0x00,0xFC,0x02,0x02,0x00,0x00,0x00,0x00,0x01,0x3E,0x40,0x40},/*"{",123*/

{0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00},/*"|",124*/

{0x02,0x02,0xFC,0x00,0x00,0x00,0x00,0x00,0x40,0x40,0x3E,0x01,0x00,0x00,0x00,0x00},/*"}",125*/

{0x00,0x02,0x01,0x02,0x02,0x04,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"~",126*/

{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00}/*"",127*/
};

chinese_font.c


#include <stdint.h>

/* 16*16, 32byte */
uint8_t g_chinese_fonts[3][32] = {


{0x00,0x80,0x60,0xF8,0x07,0x40,0x20,0x18,0x0F,0x08,0xC8,0x08,0x08,0x28,0x18,0x00,
0x01,0x00,0x00,0xFF,0x00,0x10,0x0C,0x03,0x40,0x80,0x7F,0x00,0x01,0x06,0x18,0x00},/*"你",0*/

{0x10,0x10,0xF0,0x1F,0x10,0xF0,0x00,0x80,0x82,0x82,0xE2,0x92,0x8A,0x86,0x80,0x00,
0x40,0x22,0x15,0x08,0x16,0x61,0x00,0x00,0x40,0x80,0x7F,0x00,0x00,0x00,0x00,0x00},/*"好",1*/

{0xFC,0x04,0xFC,0x00,0xFE,0x42,0xBE,0x00,0xF2,0x12,0xF2,0x02,0xFE,0x02,0x00,0x00,
0x0F,0x04,0x0F,0x00,0xFF,0x10,0x0F,0x00,0x0F,0x04,0x4F,0x80,0x7F,0x00,0x00,0x00},/*"啊",2*/
};

子模生成工具配置

在这里插入图片描述

花果山圣僧
关注
专栏目录
【OLED驱动函数详解】
ciren_Breeze的博客
05-14 2100
OLED模块函数说明
oled iic 驱动代码
05-10
iic 方式驱动oled 欢迎大家下载 有注释
IIC通信的OLED代码.rar
08-01
STM32F103C8T6驱动0.96寸的4线IIC的OLED，已经多次在自己工程中使用，完全可以使用
STM32用IIC通信实现OLED显示程序代码及取字模等软件教程
01-10
基于STM32F407的OLED程序，此程序是在中景园电子科技所写的OLED例程上面做的修改，自己加了一些注释，如有不对的地方，欢迎纠正。 文件包含内容： STM32F407OLED显示IIC接口程序； 取字模操作软件及步骤；
oled(IIc和SPI都有，亲测可用)
05-07
oled(IIc和SPI都有，亲测可用)，基本开发板的例程都有，希望对大家有帮助。
【STM32+HAL】地表最强高刷OLED显示配置【I2C】
缺积分下载资源的可以私信我或在评论区留言邮箱号
03-18 2416
一、前言 有关初级I2C版OLED配置，详见【STM32+HAL】OLED显示初始化配置 有关SPI版OLED配置，详见【STM32+HAL】七针OLED(SSD1306)配置(SPI版) 二、实现功能 开启DMA实现OLED超高刷新率超高速率传输
MSP432E401YT硬件IIC驱动0.96OLED
05-27
【MSP432E401YT微控制器与硬件IIC驱动0.96英寸OLED显示器】 MSP432E401YT是一款由德州仪器（Texas Instruments）推出的超低功耗微控制器，它属于MSP430系列，具有高性能、低功耗的特点，适用于各种嵌入式应用。这款...
45.OLED液晶-硬件IIC_OLED屏幕_
09-28
本项目将介绍如何使用STM8单片机通过IIC（Inter-Integrated Circuit）总线来驱动OLED屏幕进行显示。 首先，我们需要理解IIC总线协议。IIC是一种多主设备总线，它允许不同速度的设备在同一总线上通信。它只需要两条...
基于STM32硬件IIC DMA传输的SSD1306 OLED屏的高级应用程序
04-21
基于STM32硬件IIC DMA传输的SSD1306 OLED屏的高级应用程序。硬件IIC经过多次调试可以稳定运行。程序包括芯片手册中的屏幕旋转、亮度调节、左右滚动、向上滚动、垂直和向左或向右滚屏等。画点、画线、画实心或空心圆...
OLED.rar_OLED代码_oled_oled iic_oled开发代码_oled显示代码
09-21
在这个"OLED.rar"压缩包中，包含的是一份关于OLED显示屏的代码，特别强调了使用I2C（Inter-Integrated Circuit）通信协议进行控制。I2C是一种串行通信协议，适用于连接微控制器和其他外围设备，它只需要两根线就能...
硬件IIC的0.96寸OLED
12-27
【中景园的程序】可能是指中景园电子提供的一个示例代码或者库函数，用于帮助开发者更好地理解和使用硬件IIC的OLED显示屏。这类程序通常包括初始化I2C总线、配置OLED驱动芯片、绘制像素、显示文本等函数。开发者可以...
STM32F4 通过IIC协议操作OLED的通用示例代码，包含重要注释
W809291634的博客
09-21 819
已经实现OLED 的写字符、中文、位图。OLED的驱动C文件。
0.96oled屏，驱动ssd1306 一些不常用的命令用法和效果
CSDN博客
05-10 4349
一、引言 0.96oled一般用ssd1306驱动，ssd1306的指令丰富，但是在平常显示使用默认的初始化命令，之后就是读写显示数据了，网上的例程很多，除了常用的命令，有些命令在一些场合也有用。 初始化函数例子： //OLED显示模块初始化 void Oled_Init(void) { WriteCmd(0xae); //关显示 WriteCmd(0xd5); //设置显示时钟分频率、振荡器频率 WriteCmd(0x80);//A[3:0]:分频频率1到...
IIC协议下的OLED屏幕的三种寻址方式
Miseñor博客
05-07 2159
IIC协议下的OLED屏幕的三种寻址方式
0.96寸OLED（SSD1306）屏幕显示（二）——超长文字水平滚动
qq_35953617的博客
12-27 5099
最近，我突发奇想去翻阅了一些我本科期间所做的一些小项目，发现都挺有意思的！当年做这些项目的时候可走了很多弯路，所以想着可以将它们上传到网络上，并通过我的讲解文章可以帮助你们少走一些弯路！今天，我要分享的是一个0.96寸OLED（SSD1306）屏幕显示的学习笔记，因为我想要讲的详细一点，所以打算做成一个系列，手把手地教你学习和认识屏幕显示。由于我知识有限，如果出现一些错误，希望大家可以帮助我指出来，我们一起学习进步！！！
OLED显示屏I2C接口
热门推荐
luliplus的博客
04-06 2万+
简介 本文将介绍两种不同尺寸的OLED显示屏：0.96寸和0.91寸。他们都是4引脚I2C接口的，如下图所示： 0.96英寸OLED基本参数 工作电压：3.3~5V（内置3.3V LDO，I2C通信接口电平是3.3V的） 像素点阵规模：128x64（128列，64行，共8192颗LED） 驱动IC：SSD1306 0.91英寸OLED基本参数 工作电压：3.3~5V（内置3.3V LDO，I2C通信接口电平是3.3V的） 像素点阵规模：128x32（128列，32行，共4096颗LED
STM32驱动四线I2C的OLED例程
悟已往之不谏 知来者之可追
01-16 6513
一、原理图 二、程序 oled.c #include "oled.h" #include "stdlib.h" #include "oledfont.h" #include "delay.h" //OLED的显存 //存放格式如下. //[0]0 1 2 3 ... 127 //[1]0 1 2 3 ... 127 //[2]0 1 2 3 ... 127 //[3]0 1 2 3...
学习记录3-OLED显示模块
2301_80596293的博客
12-20 1043
4针I2C通讯OLED显示屏
STM32编写OLED显示屏驱动
m0_49476241的博客
01-23 7716
这篇文章将带大家学习如何编写OLED显示屏的驱动程序。这里我使用的是HAL库的硬件IIC，OLED屏幕使用的是SSD1306的。这里需要参考SSD1306的数据手册来编写驱动程序。这篇文章主要就是讲解了如何编写OLED的驱动程序。
hal库硬件iic驱动oled代码
最新发布
10-03
在编写使用IIC驱动 OLED 屏幕的代码时，通常会遵循以下步骤： 1. **初始化**：首先，你需要通过HAL库初始化IIC控制器，设置必要的参数，比如IIC地址、频率等。 ```c void init_iic(void) { // 初始化IIC硬件资源 ...
评论
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付：10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明：

1.余额是钱包充值的虚拟货币，按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载，可以购买VIP、付费专栏及课程。

余额充值