How do I report unmapped input/output pins of the mapped BBOX?

目录

 

lec 中如何设置 bbox 

What are the different classes of black box? How to report them?

bbox map 不上问题

分析命令：

查单个bbox 没map 的原因

 

分析不等价的原因由于bbox 。

如果是因为bbox 名字不匹配 解决办法：

如何处理由于bbox pin 对应不上导致的不等价，可以在确认逻辑的前提下ignore 掉。

如果是因为bbox 的pin 被工具默认为双向（inout）的，解决办法

---

lec 中如何设置 bbox 

set undefined cell black_box read library lib.v read design design.v…
Add notranslate module
set log file lec.log –replace read library abc.lib –revised read design golden.v read design revised.v –revised add black box *RAM *-both

 

What are the different classes of black box? How to report them?

USER
Indicates that the black box was added by the ADD BLACK BOX command
SYSTEM (empty)
Indicates that the module contains no logic.
SYSTEM (LEF)
Indicates that the macro is defined in the LEF file, but not defined in library/design modules.
SYSTEM (notranslate)
Indicates that the black box was added by the ADD NOTRANSLATE MODULES command.
SYSTEM (undefined)
Indicates that the black box was added by the SET UNDEFINED CELL black_box command.

 

bbox map 不上问题

在做lec 的时候遇到一种情况，revise 的netlist 中 子模块是bbox , 这时候发现所有的bbox 都没map 对，这是由于对于bbox 的map 主要是按照名字进行匹配的，如果名字对不上，就会说map不上。

分析命令：

Report black box –detail

查单个bbox 没map 的原因

report mapped points <bbox_inst_name> -input –output <lec mode>

 

 

分析不等价的原因由于bbox 。

Analyze noneq –type bbox -verbose

 

如果是因为bbox 名字不匹配 解决办法：

set mapping method –nobbox_name_match

delete mapped point  /inst_adrctl_master_delay/inst_cal_dly_macro/inst_cal_delay_line/inst_delay_0
delete mapped point /inst_adrctl_master_delay/inst_cal_dly_macro/inst_cal_delay_line/inst_delay_*
add renaming rule  r1  "CDN_000H_cdn_hs_phy_delay_element_EW" "CDN_000H_cdn_hs_phy_delay_0_element_EW" -Golden -pin -BBox  CDN_000H_cdn_hs_phy_delay_0_element_EW
add renaming rule  r2 "CDN_000H_cdn_hs_phy_delay_element_%d_EW" "CDN_000H_cdn_hs_phy_delay_element_EW" -Golden -pin -BBox  "CDN_000H_cdn_hs_phy_delay_element_%d_EW"
map key points
 

如何处理由于bbox pin 对应不上导致的不等价，可以在确认逻辑的前提下ignore 掉。

add ignored input <bbox_module_pin_name> -module <bbox_module_name> [-golden|-revised|-both] (Setup Mode)
This command is used to ignore inputs of a black box.
add ignored output <bbox_module_pin_name> -module <bbox_module_name> [-golden|-revised-|both] (Setup Mode)
This command is used ignore an output of a black box.
add pin constraints <0 | 1> <primary_pin* ...> -Module <bbox_module_name*> ] [-golden | -revised | -both] (Setup Mode)
This command is used to constraint the input pins of a black box to a zero/one value.
add output stuck_at <0 | 1> <primary_pin* ...> -Module <bbox_module_name*> ] [-golden | -revised | -both] (Setup Mode)
This command is used to constraint the output pin of a black box to a zero/one value.
delete black box <<blackbox_name*> ... -Module| <blackbox_name> ... -Instance | -All> [-golden | -revised | -both] (Setup Mode)
This command deletes specified blackboxes from the design. These blackboxes were created with the ADD BLACK BOX command.

如果是因为bbox 的pin 被工具默认为双向（inout）的，解决办法

assign pin direction in  CDN_000H_cdn_hs_phy_delay_0_element_EW  ret -revise
assign pin direction in  CDN_000H_cdn_hs_phy_delay_element_EW   ret -revise