【esp32-s3】5. uart定时收发

最新推荐文章于 2024-05-08 13:40:43 发布

飞鸟厌鱼

最新推荐文章于 2024-05-08 13:40:43 发布

阅读量1.3k

点赞数

分类专栏： esp32 文章标签： esp32s3

本文链接：https://blog.csdn.net/qq_38091632/article/details/124159039

版权

esp32 专栏收录该内容

42 篇文章 11 订阅

订阅专栏

1 前言

本章使用esp32s3测试uart定时发和接收。

2 硬件

在这里插入图片描述

使用IO17、18，分别为TX/RX

3 代码

/* UART asynchronous example, that uses separate RX and TX tasks

   This example code is in the Public Domain (or CC0 licensed, at your option.)

   Unless required by applicable law or agreed to in writing, this
   software is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
   CONDITIONS OF ANY KIND, either express or implied.
*/
#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "esp_system.h"
#include "esp_log.h"
#include "driver/uart.h"
#include "string.h"
#include "driver/gpio.h"

static const int RX_BUF_SIZE = 1024;

#define TXD_PIN (GPIO_NUM_17)
#define RXD_PIN (GPIO_NUM_18)
#define UART_NUM (UART_NUM_1)

void init(void) {
    
    const uart_config_t uart_config = {
        .baud_rate = 115200,
        .data_bits = UART_DATA_8_BITS,
        .parity = UART_PARITY_DISABLE,
        .stop_bits = UART_STOP_BITS_1,
        .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
        .source_clk = UART_SCLK_APB,
    };
    // We won't use a buffer for sending data.
    uart_driver_install(UART_NUM, RX_BUF_SIZE * 2, 0, 0, NULL, 0);
    uart_param_config(UART_NUM, &uart_config);
    uart_set_pin(UART_NUM, TXD_PIN, RXD_PIN, UART_PIN_NO_CHANGE, UART_PIN_NO_CHANGE);
}

int sendData(const char* logName, const char* data)
{
    const int len = strlen(data);
    const int txBytes = uart_write_bytes(UART_NUM, data, len);
    ESP_LOGI(logName, "Wrote %d bytes", txBytes);
    return txBytes;
}

static void tx_task(void *arg)
{
    static const char *TX_TASK_TAG = "TX_TASK";
    esp_log_level_set(TX_TASK_TAG, ESP_LOG_INFO);
    while (1) {
        sendData(TX_TASK_TAG, "Hello world");
        vTaskDelay(2000 / portTICK_PERIOD_MS);
    }
}

static void rx_task(void *arg)
{
    static const char *RX_TASK_TAG = "RX_TASK";
    esp_log_level_set(RX_TASK_TAG, ESP_LOG_INFO);
    uint8_t* data = (uint8_t*) malloc(RX_BUF_SIZE+1);
    while (1) {
        ESP_LOGI(RX_TASK_TAG, "IN RX");
        const int rxBytes = uart_read_bytes(UART_NUM, data, RX_BUF_SIZE, 1000 / portTICK_RATE_MS);

        printf("rxBytes: %d\n",rxBytes);
        if (rxBytes > 0) {
            data[rxBytes] = 0;
            ESP_LOGI(RX_TASK_TAG, "Read %d bytes: '%s'", rxBytes, data);
            ESP_LOG_BUFFER_HEXDUMP(RX_TASK_TAG, data, rxBytes, ESP_LOG_INFO);
        }
    }
    free(data);
}

void app_main(void)
{
    init();
    xTaskCreate(rx_task, "uart_rx_task", 1024*2, NULL, configMAX_PRIORITIES, NULL);
    xTaskCreate(tx_task, "uart_tx_task", 1024*2, NULL, configMAX_PRIORITIES-1, NULL);
}