【milkv】7、max98357a驱动添加speaker

已于 2023-11-14 21:46:01 修改
阅读量679 收藏
点赞数
分类专栏： 开发板试用 文章标签： milkv linux
于 2023-10-05 08:39:47 首次发布
版权声明：本文为博主原创文章，遵循 CC 4.0 BY-SA 版权协议，转载请附上原文出处链接和本声明。
本文链接：https://blog.csdn.net/qq_38091632/article/details/133174223
版权

文章目录

一、电路

1.1 duo音频接口

在这里插入图片描述
在这里插入图片描述
在这里插入图片描述
外接的i2s只有1和2，而2被eth复用了，需要移除eth然后再配置i2s2

1.2 I2S2连接

在这里插入图片描述

在这里插入图片描述

对应电路图中，从上到下
LRCK
BCK
DO
DI

duo可以利用i2s2外接codec+speaker进行播放音频。

二、I2S2介绍

查看cv1800的dtsi配置，可以看到其实是复用的cv1835的i2s驱动。
duo-buildroot-sdk-develop\build\boards\default\dts\cv180x\cv180x_base.dtsi

	i2s2: i2s@04120000 {
		compatible = "cvitek,cv1835-i2s";
		reg = <0x0 0x04120000 0x0 0x2000>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
		dev-id = <2>;
		#sound-dai-cells = <0>;
		dmas = <&dmac 6 1 1 /* read channel */
			&dmac 1 1 1>; /* write channel */
		dma-names = "rx", "tx";
		capability = "txrx";
		mclk_out = "false";
	};

&i2s2 {
	status = "okay";
	#sound-dai-cells = <0>;
}

我这里参考2个平台的dts
cv1835：i2s的驱动复用的该平台
cv182x：cv1800和该平台较为接近，而且adc定义有用该名称

2.1 参考cv182x的dts实现

duo-buildroot-sdk-develop\build\boards\default\dts\cv182x\cv182x_asic.dtsi

仅供参考

	i2s0: i2s@04100000 {
		compatible = "cvitek,cv1835-i2s";
		reg = <0x0 0x04100000 0x0 0x2000>;
		interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
		dev-id = <0>;
		#sound-dai-cells = <0>;
		dmas = <&dmac 0 1 1>; /* read channel */
		dma-names = "rx";
		capability = "rx"; /* I2S0 connect to internal ADC as RX */
		mclk_out = "false";
	};

	i2s1: i2s@04110000 {
		compatible = "cvitek,cv1835-i2s";
		reg = <0x0 0x04110000 0x0 0x2000>;
		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
		dev-id = <1>;
		#sound-dai-cells = <0>;
		dmas = <&dmac 2 1 1 /* read channel */
			&dmac 3 1 1>; /* write channel */
		dma-names = "rx", "tx";
		capability = "txrx";
		mclk_out = "false";
	};

	i2s2: i2s@04120000 {
		compatible = "cvitek,cv1835-i2s";
		reg = <0x0 0x04120000 0x0 0x2000>;
		interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
		dev-id = <2>;
		#sound-dai-cells = <0>;
		dmas = <&dmac 6 1 1 /* read channel */
			&dmac 1 1 1>; /* write channel */
		dma-names = "rx", "tx";
		capability = "txrx";
		mclk_out = "false";

	};

	i2s3: i2s@04130000 {
		compatible = "cvitek,cv1835-i2s";
		reg = <0x0 0x04130000 0x0 0x2000>;
		interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
		dev-id = <3>;
		#sound-dai-cells = <0>;
		dmas = <&dmac 7 1 1>; /* write channel */
		dma-names = "tx";
		capability = "tx"; /* I2S3 connect to internal DAC as TX */
		mclk_out = "true";
	};

	adc: adc@0300A100 {
		compatible = "cvitek,cv182xadc";
		reg = <0x0 0x0300A100 0x0 0x100>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
		clk_source = <0x04130000>; /* MCLK source is I2S3 */
	};

	dac: dac@0300A000 {
		compatible = "cvitek,cv182xdac";
		reg = <0x0 0x0300A000 0x0 0x100>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
	};

	pdm: pdm@0x041D0C00 {
		compatible = "cvitek,cv1835pdm";
		reg = <0x0 0x041D0C00 0x0 0x100>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
	};

	sound_adc {
		compatible = "cvitek,cv182x-adc";
		cvi,model = "CV182X";
		cvi,card_name = "cv182x_adc";
	};

	sound_dac {
		compatible = "cvitek,cv182x-dac";
		cvi,model = "CV182X";
		cvi,card_name = "cv182x_dac";
	};

	sound_PDM {
		compatible = "cvitek,cv182x-pdm";
		cvi,model = "CV182X";
		cvi,card_name = "cv182x_internal_PDM";
	};

	sound_ext1 {
		compatible = "cvitek,cv1835-adau1372";
		cvi,model = "CV1835";
		cvi,mode = "I2S";
		cvi,fmt = "IBNF";
		cvi,card_name = "cvi_sound_card_0";
		cvi,slot_no=<2>;

		dai@0 {
			cvi,dai_name = "cv1835-i2s-1";
			cvi,stream_name = "adau1372-aif";
			cvi,cpu_dai_name = "4110000.i2s";
			cvi,codec_dai_name = "adau1372-aif";
			cvi,platform_name = "4110000.i2s";
			cvi,codec_name = "adau1372.1-003c";
			cvi,role = "master";
		};
		dai@1 {
			cvi,dai_name = "cv1835-i2s-2";
			cvi,stream_name = "adau1372-aif";
			cvi,cpu_dai_name = "4120000.i2s";
			cvi,codec_dai_name = "adau1372-aif";
			cvi,platform_name = "4120000.i2s";
			cvi,codec_name = "adau1372.1-003c";
			cvi,role = "slave";
		};
	};

	/* sound_ext2 use external codec */
	sound_ext2 {
		compatible = "cvitek,cv1835-adau1372";
		cvi,model = "CV1835";
		cvi,mode = "I2S";
		cvi,fmt = "IBNF";
		cvi,card_name = "cv1835_external_card";
		cvi,slot_no=<2>;

		dai@0 {
			cvi,dai_name = "cv1835-i2s-2";
			cvi,stream_name = "adau1372-aif";
			cvi,cpu_dai_name = "4120000.i2s";
			cvi,codec_dai_name = "adau1372-aif";
			cvi,platform_name = "4120000.i2s";
			cvi,codec_name = "adau1372.0-003c";
			cvi,role = "master";
		};
		dai@1 {
			cvi,dai_name = "cv1835-i2s-3";
			cvi,stream_name = "adau1372-aif";
			cvi,cpu_dai_name = "4130000.i2s";
			cvi,codec_dai_name = "adau1372-aif";
			cvi,platform_name = "4130000.i2s";
			cvi,codec_name = "adau1372.0-003c";
			cvi,role = "slave";
		};
	};

2.2 参考cv1835_fpga

i2s的定义来看需要开cv1835相关的配置，可以参考这里定义的外接声卡。

可以参考duo-buildroot-sdk-develop\build\boards\cv183x\cv1835_fpga\linux\cv1835_fpga.dts的定义

# audio driver
#CONFIG_SOUND=y
#CONFIG_SND=y
#CONFIG_SND_SOC=y
#CONFIG_SND_CV1835_I2S=y
#CONFIG_CV1835_I2S_SUBSYS=y

# 待添加max的config

#CONFIG_SND_SOC_ADAU1372=y
#CONFIG_SND_SOC_ADAU_UTILS=y
#CONFIG_SND_SOC_ADAU1372_I2C=y
#CONFIG_SND_SOC_CV1835_ADAU1372=y
# CONFIG_SND_SOC_ADAU1372_SPI is not set
#CONFIG_SND_SOC_CV1835_CONCURRENT_I2S=y	#！！！！

#CONFIG_SND_SOC_CV1835_USE_AUDIO_PLL=y
#CONFIG_SND_SOC_CV1835_CV1835PDM=y
#CONFIG_SND_SOC_CV1835PDM=y
#CONFIG_SND_SOC_CV1835_CV1835ADC=y
#CONFIG_SND_SOC_CV1835ADC=y
#CONFIG_SND_SOC_CV1835_CV1835DAC=y
#CONFIG_SND_SOC_CV1835DAC=y

	i2s_mclk: i2s_mclk {
		clock-output-names = "i2s_mclk";
		clock-frequency = <24576000>; /* use internal audio PLL */
		#clock-cells = <0x0>;
		compatible = "fixed-clock";
	};

#ifdef CV1835_AUDIO_CODEC_EN
	adc: adc@0300A000 {
		compatible = "cvitek,cv1835adc";
		reg = <0x0 0x0300A000 0x0 0x100>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
	};

	dac: dac@0300A400 {
		compatible = "cvitek,cv1835dac";
		reg = <0x0 0x0300A400 0x0 0x100>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
	};

	sound_adc {
		compatible = "cvitek,cv1835-adc";
		cvi,model = "CV1835";
		cvi,card_name = "cvi_adc";
	};

	sound_dac {
		compatible = "cvitek,cv1835-dac";
		cvi,model = "CV1835";
		cvi,card_name = "cvi_dac";
	};
#endif


	i2s0: i2s@04100000 {
		compatible = "cvitek,cv1835-i2s";
		reg = <0x0 0x04100000 0x0 0x2000>;
		interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
		dev-id = <0>;
		#sound-dai-cells = <0>;
		dmas = <&dmac 0 1 1 /* read channel */
			&dmac 1 1 1>; /* write channel */
		dma-names = "rx", "tx";
		capability = "rx"; /* I2S0 connect to internal ADC as RX */
	};

	i2s1: i2s@04110000 {
		compatible = "cvitek,cv1835-i2s";
		reg = <0x0 0x04110000 0x0 0x2000>;
		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
		dev-id = <1>;
		#sound-dai-cells = <0>;
		dmas = <&dmac 2 1 1 /* read channel */
			&dmac 3 1 1>; /* write channel */
		dma-names = "rx", "tx";
#ifndef CV1835_CONCURRENT_I2S /* refer to /include/dt-bindings/sound/cv1835-audio.h */
		capability = "txrx";
#else
		capability = "tx";
#endif
	};

#ifdef CV1835_EXT_CARD_1_EN
	/* sound_ext1 use external codec */
	sound_ext1 {
		compatible = "cvitek,cv1835-adau1372";
		cvi,model = "CV1835";
		cvi,mode = "I2S";
		cvi,fmt = "IBNF";
		cvi,card_name = "cvi_sound_card_0";
		cvi,slot_no=<2>;
		dai@0 {
			cvi,dai_name = "cv1835-i2s-1";
			cvi,stream_name = "adau1372-aif";
			cvi,cpu_dai_name = "4110000.i2s";
			cvi,codec_dai_name = "adau1372-aif";
			cvi,platform_name = "4110000.i2s";
			cvi,codec_name = "adau1372.0-003c";
			cvi,role = "master";
		};
#ifdef CV1835_CONCURRENT_I2S
		dai@1 {
			cvi,dai_name = "cv1835-i2s-0";
			cvi,stream_name = "adau1372-aif";
			cvi,cpu_dai_name = "4100000.i2s";
			cvi,codec_dai_name = "adau1372-aif";
			cvi,platform_name = "4100000.i2s";
			cvi,codec_name = "adau1372.0-003c";
			cvi,role = "slave";
		};
#endif
	};
#endif

	pdm: pdm@0x041D0C00 {
		compatible = "cvitek,cv1835pdm";
		reg = <0x0 0x041D0C00 0x0 0x100>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
	};

#ifdef CV1835_PDM_EN
	/* sound_PDM use PDM to transfer DMIC signal to I2S signal as audio input */
	sound_PDM {
		compatible = "cvitek,cv1835-pdm";
		cvi,model = "CV1835";
		cvi,card_name = "cv1835_internal_PDM";
	};
#endif

	i2s2: i2s@04120000 {
		compatible = "cvitek,cv1835-i2s";
		reg = <0x0 0x04120000 0x0 0x2000>;
		interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
		dev-id = <2>;
		#sound-dai-cells = <0>;
		dmas = <&dmac 4 1 1 /* read channel */
			&dmac 5 1 1>; /* write channel */
		dma-names = "rx", "tx";
#ifndef CV1835_CONCURRENT_I2S
		capability = "txrx";
#else
		capability = "rx";
#endif
	};

	i2s3: i2s@04130000 {
		compatible = "cvitek,cv1835-i2s";
		reg = <0x0 0x04130000 0x0 0x2000>;
		interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
		dev-id = <3>;
		#sound-dai-cells = <0>;
		dmas = <&dmac 6 1 1 /* read channel */
			&dmac 7 1 1>; /* write channel */
		dma-names = "rx", "tx";
		capability = "tx"; /* I2S3 connect to internal DAC as TX */
	};
#ifdef CV1835_EXT_CARD_2_EN
	/* sound_ext2 use external codec */
	sound_ext2 {
		compatible = "cvitek,cv1835-adau1372";
		cvi,model = "CV1835";
		cvi,mode = "I2S";
		cvi,fmt = "IBNF";
		cvi,card_name = "cv1835_external_card";
		cvi,slot_no=<2>;

		dai@0 {
			cvi,dai_name = "cv1835-i2s-2";
			cvi,stream_name = "adau1372-aif";
			cvi,cpu_dai_name = "4120000.i2s";
			cvi,codec_dai_name = "adau1372-aif";
			cvi,platform_name = "4120000.i2s";
			cvi,codec_name = "adau1372.0-003c";
			cvi,role = "master";
		};
#ifdef CV1835_CONCURRENT_I2S
		dai@1 {
			cvi,dai_name = "cv1835-i2s-3";
			cvi,stream_name = "adau1372-aif";
			cvi,cpu_dai_name = "4130000.i2s";
			cvi,codec_dai_name = "adau1372-aif";
			cvi,platform_name = "4130000.i2s";
			cvi,codec_name = "adau1372.0-003c";
			cvi,role = "slave";
		};
#endif
	};
#endif

2.3 cv180x

cv1800b_milkv_duo_sd.dts

  • cv180x_base_riscv.dtsi
    • cv180x_base.dtsi （定义i2s接口）
  • cv180x_asic_qfn.dtsi （移除sound接口）
  • cv180x_asic_sd.dtsi
  • cv180x_default_memmap.dtsi

在这里插入图片描述

平台定义的i2s接口，最终包该定义。
cv180x_base.dtsi
duo-buildroot-sdk-develop\build\boards\default\dts\cv180x

	i2s_mclk: i2s_mclk {
		clock-output-names = "i2s_mclk";
		clock-frequency = <24576000>;
		#clock-cells = <0x0>;
		compatible = "fixed-clock";
	};

	i2s_subsys {
		compatible = "cvitek,i2s_tdm_subsys";
		reg = <0x0 0x04108000 0x0 0x100>;
		clocks = <&i2s_mclk>, <&clk CV180X_CLK_A0PLL>,
			<&clk CV180X_CLK_SDMA_AUD0>, <&clk CV180X_CLK_SDMA_AUD1>,
			<&clk CV180X_CLK_SDMA_AUD2>, <&clk CV180X_CLK_SDMA_AUD3>;
		clock-names = "i2sclk", "clk_a0pll",
			"clk_sdma_aud0", "clk_sdma_aud1",
			"clk_sdma_aud2", "clk_sdma_aud3";
		master_base = <0x04110000>; /* I2S1 is master, only useful while using multi I2S IPs work on same IO */
	};

	i2s0: i2s@04100000 {
		compatible = "cvitek,cv1835-i2s";
		reg = <0x0 0x04100000 0x0 0x2000>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
		dev-id = <0>;
		#sound-dai-cells = <0>;
		dmas = <&dmac 0 1 1>; /* read channel */
		dma-names = "rx";
		capability = "rx"; /* I2S0 connect to internal ADC as RX */
		mclk_out = "false";
	};

	i2s1: i2s@04110000 {
		compatible = "cvitek,cv1835-i2s";
		reg = <0x0 0x04110000 0x0 0x2000>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
		dev-id = <1>;
		#sound-dai-cells = <0>;
		dmas = <&dmac 2 1 1 /* read channel */
			&dmac 3 1 1>; /* write channel */
		dma-names = "rx", "tx";
		capability = "txrx";
		mclk_out = "false";
	};

	i2s2: i2s@04120000 {
		compatible = "cvitek,cv1835-i2s";
		reg = <0x0 0x04120000 0x0 0x2000>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
		dev-id = <2>;
		#sound-dai-cells = <0>;
		dmas = <&dmac 6 1 1 /* read channel */
			&dmac 1 1 1>; /* write channel */
		dma-names = "rx", "tx";
		capability = "txrx";
		mclk_out = "false";

	};

	i2s3: i2s@04130000 {
		compatible = "cvitek,cv1835-i2s";
		reg = <0x0 0x04130000 0x0 0x2000>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
		dev-id = <3>;
		#sound-dai-cells = <0>;
		dmas = <&dmac 7 1 1>; /* write channel */
		dma-names = "tx";
		capability = "tx"; /* I2S3 connect to internal DAC as TX */
		mclk_out = "true";
	};

cv180x_base_riscv.dtsi

	i2s0: i2s@04100000 {
		interrupts = <40 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-parent = <&plic0>;
	};

	i2s1: i2s@04110000 {
		interrupts = <41 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-parent = <&plic0>;
	};

	i2s2: i2s@04120000 {
		interrupts = <42 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-parent = <&plic0>;
	};

	i2s3: i2s@04130000 {
		interrupts = <43 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-parent = <&plic0>;
	};

cv180x_asic_qfn.dtsi

	/delete-node/ i2s@04110000;
	/delete-node/ i2s@04120000;
	/delete-node/ sound_ext1;
	/delete-node/ sound_ext2;
	/delete-node/ sound_PDM;

cv1800移除了i2s1&i2s2，我们需要启动该节点。

PS：可以通过dtsi最终生成的tmp文件查看节点状况
路径：duo_buildroot_sdk\duo-buildroot-sdk\u-boot-2021.10\build\cv1800b_milkv_duo_sd\arch\riscv\dts.cv1800b_milkv_duo_sd.dtb.dts.tmp

2.4 改动——保留i2s

cv180x_asic_qfn.dtsi

	/delete-node/ i2s@04110000;

	/delete-node/ sound_ext1;
	/delete-node/ sound_ext2;
	/delete-node/ sound_PDM;

删除i2s2的移除配置。

2.5 I2S小结

为了eth做准备，默认是删除i2s2。
我们需要保留i2s2的配置。

cv1800没有定义i2s的外接声卡，只有内部使用的pdm、adc、dac。
speaker需要自己添加声卡驱动以及声卡节点。

三、参考资料

3.1 文章

https://blog.csdn.net/pingis58/article/details/109235204
https://github.com/beagleboard/bb.org-overlays/issues/39

https://cloud.tencent.com/developer/article/2225253

3.2 手册

在这里插入图片描述
数据手册
https://www.analog.com/media/en/technical-documentation/data-sheets/MAX98357A-MAX98357B.pdf

max98357a用i2s接口，我们只要用如下引脚：
LRC：左右声道选择
BCLK：采样信号
DIN：音频数据输入
Vin：电源
GND：接地

gain和sd-mode驱动里也有定义，需要自己增加接口去控制，后续再说。

四、驱动路径

max98357a驱动：
duo-buildroot-sdk-develop\linux_5.10\sound\soc\codecs\max98357a.c

duo-buildroot-sdk-develop\linux_5.10\sound\soc\codecs\Makefile

snd-soc-max98357a-objs := max98357a.o

obj-$(CONFIG_SND_SOC_MAX98357A)	+= snd-soc-max98357a.o

duo-buildroot-sdk-develop\linux_5.10\sound\soc\Makefile

obj-$(CONFIG_SND_SOC)	+= snd-soc-core.o
obj-$(CONFIG_SND_SOC)	+= codecs/

duo-buildroot-sdk-develop\linux_5.10\sound\Makefile

obj-$(CONFIG_SOUND) += soundcore.o
obj-$(CONFIG_SND) += core/ i2c/ drivers/ isa/ pci/ ppc/ arm/ sh/ synth/ usb/ \
	firewire/ sparc/ spi/ parisc/ pcmcia/ mips/ soc/ atmel/ hda/ x86/ xen/

duo-buildroot-sdk-develop\linux_5.10\Makefile

drivers-y	:= drivers/ sound/

所以需要打开的config如下

CONFIG_SND_SOC=y
CONFIG_SOUND=y
CONFIG_SND=y

五、添加codec驱动——max98357a

5.1 config

如上章介绍的，codec路径下的配置，所以加载codec驱动需要配置config。

CONFIG_SND_SOC_MAX98357A=y

5.2 dtsi

duo-buildroot-sdk-develop\linux_5.10\sound\soc\codecs\max98357a.c

#ifdef CONFIG_OF
static const struct of_device_id max98357a_device_id[] = {
	{ .compatible = "maxim,max98357a" },
	{ .compatible = "maxim,max98360a" },
	{}
};
MODULE_DEVICE_TABLE(of, max98357a_device_id);
#endif

dtsi中需要匹配该节点，增加如下配置，让codec可以正常加载。

	/* codec */
	max98357a: max98357a {
		#sound-dai-cells = <0>;
		compatible = "maxim,max98357a";
		status = "okay";
		/*sdmode-gpios = <&gpio1 14 0>;*/ 
		/* max98357a has gain & sd_mode gpio. but codec driver just has sdmode */
	};

5.3 dai_driver

这里的dai_driver后续会在machine驱动中使用到，注意name。

static struct snd_soc_dai_driver max98357a_dai_driver = {
	.name = "HiFi",
	.playback = {
		.stream_name	= "HiFi Playback",
		.formats	= SNDRV_PCM_FMTBIT_S16 |
					SNDRV_PCM_FMTBIT_S24 |
					SNDRV_PCM_FMTBIT_S32,
		.rates		= SNDRV_PCM_RATE_8000 |
					SNDRV_PCM_RATE_16000 |
					SNDRV_PCM_RATE_32000 |
					SNDRV_PCM_RATE_44100 |
					SNDRV_PCM_RATE_48000 |
					SNDRV_PCM_RATE_88200 |
					SNDRV_PCM_RATE_96000,
		.rate_min	= 8000,
		.rate_max	= 96000,
		.channels_min	= 1,
		.channels_max	= 2,
	},
	.ops    = &max98357a_dai_ops,
};

六、查看platform/cpu

duo-buildroot-sdk-develop\linux_5.10\sound\soc\cvitek\Makefile

使用的是i2s2，注意需要打开i2s2节点。

Makefile

# Cvitek Platform Support
obj-$(CONFIG_SND_CV1835_I2S) += cv1835_i2s.o

	i2s2: i2s@04120000 {
		compatible = "cvitek,cv1835-i2s";
		reg = <0x0 0x04120000 0x0 0x2000>;
		clocks = <&i2s_mclk 0>;
		clock-names = "i2sclk";
		dev-id = <2>;
		#sound-dai-cells = <0>;
		dmas = <&dmac 6 1 1 /* read channel */
			&dmac 1 1 1>; /* write channel */
		dma-names = "rx", "tx";
		capability = "txrx";
		mclk_out = "false";
	};

七、添加machin驱动

7.1 仿照182x，183x

这里定义的cpu_dai_name，由于audio的dapm接口已经变化了，之前的name方式加载被弃用。
若还用下述配置，则导致编译不过。

	/* machine -- sound card*/
#ifdef CV1835_EXT_CARD_3_EN
	/* sound_ext3 use external codec */
	sound_ext3 {
		compatible = "cvitek,cv1835-max98357a";
		cvi,model = "CV1835";
		cvi,mode = "I2S";
		cvi,fmt = "IBNF";
		cvi,card_name = "cv1835_external_card_max98357a";
		cvi,slot_no=<2>;

		dai@0 {
			cvi,dai_name = "cv1835-i2s-2";
			cvi,stream_name = "HiFi";
			cvi,cpu_dai_name = "4120000.i2s";
			cvi,codec_dai_name = "HiFi";
			cvi,platform_name = "4120000.i2s";
			cvi,codec_name = "MX98357A:00";
			cvi,role = "master";
		};
	};
#endif

7.2 重新定义dai_link

SND_SOC_DAILINK_DEFS(dailink_max98357a,
	DAILINK_COMP_ARRAY(COMP_CPU("4120000.i2s")),
	DAILINK_COMP_ARRAY(COMP_CODEC("max98357a", "HiFi")),
	DAILINK_COMP_ARRAY(COMP_PLATFORM("4120000.i2s")));

static struct snd_soc_dai_link cv1835_max98357a_dai[] = {
	[DPCM_AUDIO_SPKR] = {
		.name = "max98357a",
		.stream_name = "max98357a i2s",	//"cv1835-max98357a",
		.init = cv1835_max98357a_asoc_init,
		.ops = &cv1835_max98357a_ops,
		.dai_fmt = SND_SOC_DAIFMT_I2S
		| SND_SOC_DAIFMT_IB_NF
		| SND_SOC_DAIFMT_CBS_CFS,
		SND_SOC_DAILINK_REG(dailink_max98357a),

		// Interface Abandonment
		// .cpu_dai_name= "4120000.i2s",
		// .codec_dai_name = "HiFi",
		// .codec_name = "maxim,max98357a",
		// .platform_name= "4120000.i2s",
	},
};

7.3 添加驱动

添加驱动代码
duo-buildroot-sdk-develop\linux_5.10\sound\soc\cvitek\cv1835_max98357a.c

先编译看看能不能成功添加驱动

// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * Machine driver for EVAL-ADAU1372 on CVITEK CV1835
 *
 * Copyright 2019 CVITEK
 *
 * Author: EthanChen
 *
 */

#include <linux/module.h>
#include <linux/device.h>
#include <sound/core.h>
#include <sound/pcm.h>
#include <sound/soc.h>
#include <sound/pcm_params.h>
#include <linux/io.h>
#include <linux/proc_fs.h>

// // u16 tdm_slot_no = 2;


struct card_private {
	int tmp;	//save sth.
	// struct snd_soc_jack headset;
	// struct list_head hdmi_pcm_list;
	// struct snd_soc_jack hdmi[3];
};

enum {
	DPCM_AUDIO_SPKR = 0,
};

static const struct snd_soc_dapm_widget cv1835_max98357a_dapm_widgets[] = {
	SND_SOC_DAPM_SPK("SPKR", NULL),		// diff "Speaker" in max98357a
};

static const struct snd_soc_dapm_route cv1835_max98357a_dapm_routes[] = {
	{"SPKR", NULL, "Speaker"},
};

static int cv1835_max98357a_hw_params(struct snd_pcm_substream *substream,
				     struct snd_pcm_hw_params *params)
{
	return 0;
}

static int cv1835_max98357a_asoc_init(struct snd_soc_pcm_runtime *rtd)
{
	// dual with private data


	// struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
	// struct snd_soc_dai *codec_dai = rtd->codec_dai;
	// u32 ret;

	// /* Only need to set slot number while mode is TDM/PDM, otherwise default slot number is 2 */
	// if (tdm_slot_no != 2) {
	// 	ret = snd_soc_dai_set_tdm_slot(codec_dai, 0x0F, 0x0F, tdm_slot_no, 32);

	// 	if (ret < 0)
	// 		return ret;

	// 	ret = snd_soc_dai_set_tdm_slot(cpu_dai, 0x0F, 0x0F, tdm_slot_no, 32);

	// 	if (ret < 0)
	// 		return ret;
	// }

	return 0;
}

static struct snd_soc_ops cv1835_max98357a_ops = {
	.hw_params = cv1835_max98357a_hw_params,
};

SND_SOC_DAILINK_DEFS(dailink_max98357a,
	DAILINK_COMP_ARRAY(COMP_CPU("4120000.i2s")),
	DAILINK_COMP_ARRAY(COMP_CODEC("max98357a", "HiFi")),
	DAILINK_COMP_ARRAY(COMP_PLATFORM("4120000.i2s")));

static struct snd_soc_dai_link cv1835_max98357a_dai[] = {
	[DPCM_AUDIO_SPKR] = {
		.name = "max98357a",
		.stream_name = "max98357a i2s",	//"cv1835-max98357a",
		.init = cv1835_max98357a_asoc_init,
		.ops = &cv1835_max98357a_ops,
		.dai_fmt = SND_SOC_DAIFMT_I2S
		| SND_SOC_DAIFMT_IB_NF
		| SND_SOC_DAIFMT_CBS_CFS,
		SND_SOC_DAILINK_REG(dailink_max98357a),
	},
};


static struct snd_soc_card cv1835_max98357a = {
	.name = "cv1835 max98357a",	// card name
	.owner = THIS_MODULE,
	.dai_link = cv1835_max98357a_dai,
	.num_links = ARRAY_SIZE(cv1835_max98357a_dai),

	// control may don't have
	// .controls = skylake_controls,
	// .num_controls = ARRAY_SIZE(skylake_controls),

	.dapm_widgets		= cv1835_max98357a_dapm_widgets,
	.num_dapm_widgets	= ARRAY_SIZE(cv1835_max98357a_dapm_widgets),

	.dapm_routes		= cv1835_max98357a_dapm_routes,
	.num_dapm_routes	= ARRAY_SIZE(cv1835_max98357a_dapm_routes),

	// .fully_routed = true,
	// .late_probe = skylake_card_late_probe,
};

static const struct of_device_id cvi_audio_match_ids[] = {
	{
		.compatible = "cvitek,cv1835-max98357a",
		//.data = (void *) &cv1835_max98357a_dai,
	},
	{},
};
MODULE_DEVICE_TABLE(of, cvi_audio_match_ids);


static int cv1835_max98357a_probe(struct platform_device *pdev)
{
	struct device_node *np = pdev->dev.of_node;
	struct snd_soc_card *card = &cv1835_max98357a;

	struct card_private *ctx;		// create private data for card
	int ret;

	// struct device_node *np = pdev->dev.of_node, *dai;

	// dev_info("snd card name = %s",card->name);

	ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
	if (!ctx)
		return -ENOMEM;

	card->dev = &pdev->dev;
	snd_soc_card_set_drvdata(card, ctx);	//save card info to snd_card

	ret = devm_snd_soc_register_card(&pdev->dev, card);
	if (ret) {
		dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n",
			ret);
		return ret;
	}

	return 0;
}

static struct platform_driver cv1835_max98357a_driver = {
	.driver = {
		.name = "cv1835-max98357a",
		.pm = &snd_soc_pm_ops,
		.of_match_table = cvi_audio_match_ids,
	},
	.probe = cv1835_max98357a_probe,
};

module_platform_driver(cv1835_max98357a_driver);

MODULE_AUTHOR("EthanChen");
MODULE_DESCRIPTION("ALSA SoC cv1835 max98357a driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:cv1835-max98357a");

7.4 添加Kconfig

config SND_SOC_CV1835_MAX98357A
	tristate "Support for the max98357a card"
	help
	  max98357a codec enable.

7.5 添加makefile

obj-$(CONFIG_SND_SOC_CV1835_MAX98357A) += cv1800_max98357a.o

7.6 打开config

CONFIG_SND_SOC_CV1835_MAX98357A为了加载machine驱动。
CONFIG_SND_SOC_MAX98357A加载codec驱动。
CONFIG_SND_CV1835_I2S加载cpu/platform驱动。

CONFIG_SND_PROC_FS打开proc接口实现，用于/proc/asound目录下的声卡信息。

# sound -- max98357a
CONFIG_SND_SOC_CV1835_MAX98357A=y
CONFIG_SND_SOC_MAX98357A=y

CONFIG_SND_PROC_FS=y

CONFIG_SOUND=y
CONFIG_SND=y
CONFIG_SND_SOC=y
CONFIG_SND_CV1835_I2S=y
CONFIG_CV1835_I2S_SUBSYS=y
CONFIG_SND_SOC_CV1835_CONCURRENT_I2S=y

八、问题

8.1 /proc/asound目录没有生成

CONFIG_SND_PROC_FS

查看config最终生成文件
路径：duo-buildroot-sdk\linux_5.10\build\cv1800b_milkv_duo_sd.config

makefile

ifneq ($(CONFIG_SND_PROC_FS),)
snd-y += info.o
snd-$(CONFIG_SND_OSSEMUL) += info_oss.o
endif

asound目录下存放这些内容
info.c

int snd_info_check_reserved_words(const char *str)
{
	static const char * const reserved[] =
	{
		"version",
		"meminfo",
		"memdebug",
		"detect",
		"devices",
		"oss",
		"cards",
		"timers",
		"synth",
		"pcm",
		"seq",
		NULL
	};
	const char * const *xstr = reserved;

	while (*xstr) {
		if (!strcmp(*xstr, str))
			return 0;
		xstr++;
	}
	if (!strncmp(str, "card", 4))
		return 0;
	return 1;
}

alsa源码
duo-buildroot-sdk-develop\linux_5.10\sound\core\sound.c

8.2 使用audio_debug读取adc、i2s0/2，状态未打开

查看dts，状态是ok的

查看dts生成文件
路径：duo-buildroot-sdk\u-boot-2021.10\build\cv1800b_milkv_duo_sd\arch\riscv\dts.cv1800b_milkv_duo_sd.dtb.dts.tmp

由于驱动中没有添加该实现，所以显示的状态不对。
需要在dtsi中添加信息，并在code中增加处理。

8.3 mclk

可能不需要添加，这个看芯片是否支持

duo-buildroot-sdk-develop\linux_5.10\sound\soc\cvitek\cv1835_i2s.c
这里可能需要开config，以及定义dts中mclk_out

	device_property_read_string(&pdev->dev, "mclk_out", &mclk_out);

	if (!strcmp(mclk_out, "true"))
		dev->mclk_out = true;
	else
		dev->mclk_out = false;

	val = i2s_read_reg(dev->i2s_base, I2S_CLK_CTRL0);
	val &= ~(AUD_CLK_SOURCE_MASK);
	val &= ~(BCLK_OUT_FORCE_EN); /* blck_out output after transmission start */
#if defined(CONFIG_SND_SOC_CV1835_USE_AUDIO_PLL)
	if (dev->mclk_out == true)
		i2s_write_reg(dev->i2s_base, I2S_CLK_CTRL0, val | AUD_CLK_FROM_PLL | MCLK_OUT_EN | AUD_ENABLE);
	/* Turn aud_en on due to external codec might need MCLK to do register initialization */
	else
		i2s_write_reg(dev->i2s_base, I2S_CLK_CTRL0, val | AUD_CLK_FROM_PLL);
#else
	i2s_write_reg(dev->i2s_base, I2S_CLK_CTRL0, val | AUD_CLK_FROM_MCLK_IN);
#endif

九、结果

9.1 编译

  CC      sound/soc/codecs/max98357a.o
  CC      sound/soc/cvitek/cv1835_max98357a.o

9.2 设备查看

如图，声卡加载成功。
在这里插入图片描述

小结

本章介绍如何添加max98357a的驱动并成功加载。

飞鸟厌鱼
关注
  • 0
    点赞
  • 踩
  • 0
    收藏
    觉得还不错? 一键收藏
  • 1
    评论
专栏目录
【ESP32使用MAX98357播放音频】
vor234的博客
04-14 1099
在物联网和智能家居领域，音频播放功能越来越受到重视。ESP32作为一款功能强大的微控制器，结合MAX98357音频放大器模块，可以实现高品质的音频播放。本文将详细介绍如何使用ESP32的I2S接口通过MAX98357进行音频播放。
ESP32驱动-MAX98357-I2S数字功放驱动
视觉与物联智能
06-19 2167
MAX98357和MAX98358数字输入D类音频功率放大器，帮助设计者以高性价比实现紧凑、高效、即插即用的方案。除了拥有小尺寸外形，器件能够以D类放大器效率实现3.2W的AB类放大器音质，获得绝佳的高保真音效，适合各种产品应用。
基于NXP iMX6ULL 扩展音频解码器 MAX98357A
toradexsh的博客
01-07 2284
By Toradex胡珊逢 Colibri iMX6ULL是Toradex面向低成本设备推出的Arm计算机模块。该产品没有音频编解码器，无法直接输出模拟音频信号。本文将介绍如何使用模块的数字音频I2S接口扩展MAX98357A，包括如何配置device tree和时钟。 在Colibri iMX6ULL模块上的i.MX 6ULL SoC通过synchronous audio interfaces（SAI）接口提供数字音频接口，可以支持AC97或者I2S以连接外部音...
树莓派使用通过i2s使用MAX98357播放音频
qq_44627590的博客
03-13 1619
树莓派通过i2s使用max98357模块输出音频
【基于MAX98357的Minimax（百度）长文本语音合成TTS 接入教程】
最新发布
vor234的博客
05-03 2192
随着物联网技术的快速发展，智能设备的交互方式也在不断进化。语音合成技术（TTS）作为人机交互的重要组成部分，正变得越来越普及。本文将介绍如何利用ESP32S3N8R8开发板与MAX98357音频放大器结合，实现与Minimax长文本语音合成服务的集成，打造一个功能丰富的语音交互系统。
ESP32-IDF使用I2S驱动MAX98375--解析WAV文件
weixin_44678052的博客
09-22 907
本篇文章将介绍如何使用ESP32S3通过I2S发送WAV音频数据，驱动MAX98375A进行音频的播放。是EVE_V2项目开发的一部分工作。芯片特性如下，可以在芯片手册上找到。单电源工作(2.5V至5.5V)3.2W输出功率：4Ω，5V2.4mA静态电流92%效率(RL = 8Ω,POUT = 1W)25µVRMS输出噪声(AV = 15dB)1kHz时，0.015% THD+N无需MCLK8kHz至96kHz采样速率支持左声道、右声道以及(左声道/2 + 右声道/2)输出。
K210(SiPEED MaixBit)MicroPython使用参考（十、MAX98357A的I2S驱动）
sdau2005的博客
08-20 2516
以K210为主控的SiPEED MaixBit的使用参考，此部分整理了K210驱动MAX98357的MicroPython代码，并提供了2个测试音频文件，TM8211亦得以验证通过。
AM335X添加声卡驱动max98357a记录_基于TI官方PSDK
pingis58的博客
10-23 2028
0.硬件平台信息 前篇文章有描述，我们自制硬件平台是使用OSD335X SM芯片，集成了AM335X，DDR3，PMIC，EEPROM。硬件设计上少了很多麻烦，及CPU，DDR测试上的很多麻烦。官方开发板参考BBB开发板设计。我们自制硬件有少许改动，所以基础的DTS文件，是基于BBB的DTS上修改。 声卡芯片，我们选用的是MAX98357A，使用MCASP0，连接了MCASP0_ACLKX,MCASP0_AXR0,MCASP0_FSX。 1.查找驱动文件 一般使用较多的芯片，LINUX源码包中都包含有现成驱
基于I2S通讯MAX98357模块的JetsonNano声音外放
星羽空间
02-11 2451
基于I2S通讯MAX98357模块的JetsonNano声音外放
一起玩儿物联网人工智能小车（ESP32）——68 使用MAX98357A模块播放声音
一起玩儿科技
02-24 2366
摘要：本文介绍如何使用MAX98357A模块播放声音
【ESP32音视频传输】①用I2S通过内部DAC或MAX98357A播放音乐/录音数据及接受网络广播
热门推荐
loveliveoil的博客
04-12 2万+
esp32在arduino环境下，进行音频开发，包括外接MAX98357A或利用内部DAC输出音频信号
LT6911C+MAX98357AETE HDMI-To-MIPI转换板ALTIUM设计硬件原理图+PCB文件.zip
12-22
LT6911C+MAX98357AETE HDMI_To_MIPI转换板ALTIUM设计硬件原理图+PCB文件，2层板设计，大小为145x70mm，Altium Designer 设计的工程文件，包括完整的原理图及PCB文件，可以用Altium(AD)软件打开或修改，主要器件包括LT6911C，MAX98357AETE，EA3036，RT9293等，可以做为你的学习设计参考。
乐视max2手机usb驱动 官方版
07-11
乐视max2驱动是专为购买了乐视max2手机的用户打造的驱动程序，有了它以后，用户就可以让手机和电脑进行互联，进行文件、视频图片的传输了，欢迎有需要的朋友下载使用！乐视max2参数简介手机类型4G手机，3G手机，智能...
MAX31586单片机驱动程序
11-29
MAX31865驱动程序+中文资料+英文资料，欢迎下载交流~
MAX485_主动竞争驱动.rar
11-22
MAX485_主动竞争驱动，利用MAX485设备地址竞争，内含4个文件，包含USART底层驱动设计和MAX485中间层设备驱动设计，自己已在工程中使用，教程链接https://blog.csdn.net/qq_33784286/article/details/121427290
usb转串口线驱动（max232）
10-20
配合本人上传的“自制STC单片机编程器”使用！ 配合本人上传的“自制STC单片机编程器”使用！ 配合本人上传的“自制STC单片机编程器”使用！ 配合本人上传的“自制STC单片机编程器”使用！
max打印机驱动.rar
07-03
支持MAX L390 L550 系列的打印机进行联机打印作业，极大的提高效率，界面操作简单。亲测可用。
物联网开发笔记（51）- 使用Micropython开发ESP32开发板之通过MAX98357 I2S音频模块播放音乐
zhusongziye的博客
11-24 5185
使用Micropython开发ESP32开发板之通过MAX98357 I2S音频模块播放音乐
max98357 的几点说明
Sean.Pu的专栏
01-21 715
所以，使用两个max98357 就可以实现左右声道，想想这不单是苦X而且是傻X.你自己用的时候这个模块就必须来两个，很奇怪的芯片，所以才莫名产生了误导。某个角度也是提供了一种思路，也不算啥坏事，大不鸟真的使用两块芯片，因为其他U系列双声道的有点贵啊！max98357都可以控制SD脚的电压控制为左右声道输出，这个被误导了，有些使用这个模块的也没有说清楚。左右声道的选择是控制SD卡的电压，所以意味着需要串联不同的电阻。这个模块和其他可以直接输出左右声道的不同，大哭。
MAX98357驱动代码
08-15
MAX98357是一款音频功率放大器芯片，常用于音频应用中。以下是一个基本的驱动代码示例，使用 Raspberry Pi 来控制 MAX98357： ```python import RPi.GPIO as GPIO import time # 定义 MAX98357 的引脚 RESET_PIN = 5 SD_PIN = 6 LRC_PIN = 13 DIN_PIN = 19 BCLK_PIN = 26 # 初始化 GPIO 引脚 GPIO.setmode(GPIO.BCM) GPIO.setup(RESET_PIN, GPIO.OUT) GPIO.setup(SD_PIN, GPIO.OUT) GPIO.setup(LRC_PIN, GPIO.OUT) GPIO.setup(DIN_PIN, GPIO.OUT) GPIO.setup(BCLK_PIN, GPIO.OUT) # 重置 MAX98357 GPIO.output(RESET_PIN, GPIO.LOW) time.sleep(0.01) GPIO.output(RESET_PIN, GPIO.HIGH) # 设定 MAX98357 的工作模式和格式 GPIO.output(SD_PIN, GPIO.LOW) # SD 为低电平，表示 I2S 格式 GPIO.output(LRC_PIN, GPIO.HIGH) # LRC 为高电平，表示 32位数据宽度 # 播放音频数据 def play_audio(data): for i in range(len(data)): for j in range(32): GPIO.output(BCLK_PIN, GPIO.LOW) if (data[i] & (1 << (31 - j))) != 0: GPIO.output(DIN_PIN, GPIO.HIGH) else: GPIO.output(DIN_PIN, GPIO.LOW) GPIO.output(BCLK_PIN, GPIO.HIGH) time.sleep(0.000001) # 示例音频数据 audio_data = [0x00FFFFFF, 0x00000000, 0x00FFFFFF, 0x00000000] # 播放音频 play_audio(audio_data) # 清理 GPIO 引脚设置 GPIO.cleanup() ``` 请注意，此代码只是一个基本示例，具体的驱动代码可能会根据您的硬件和应用场景有所不同。确保正确连接 MAX98357 的引脚，并在代码中进行相应的配置。此外，还需要安装 RPi.GPIO 库来控制 Raspberry Pi 的 GPIO 引脚。

“相关推荐”对你有帮助么？

  • 非常没帮助
  • 没帮助
  • 一般
  • 有帮助
  • 非常有帮助
提交
评论 1
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付：10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明：

1.余额是钱包充值的虚拟货币，按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载，可以购买VIP、付费专栏及课程。

余额充值