STM32 自定义频率与占空比PWM输出

一、本实例所使用资源：

1、 PWM输出：TIM3_CH1(对应管脚PA6)
2、 PWM输出：TIM3_CH2(对应管脚PA7)
3、 MDK 软件仿真

二、步骤

1、 初始化对应GPIO
2、 配置定时器TIM3
3、 main函数调用初始化

三、代码

static void Timer_GPIO_Config(void)
{
	GPIO_InitTypeDef GPIO_InitStructure;
	
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);
	
  GPIO_InitStructure.GPIO_Pin =  GPIO_Pin_6 | GPIO_Pin_7;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

  GPIO_Init(GPIOA, &GPIO_InitStructure);

}

static void Timer_Config(void)
{
	TIM_TimeBaseInitTypeDef  TIM_TimeBaseStructure;
	TIM_OCInitTypeDef  TIM_OCInitStructure;
	
	RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE);
	
	//TIME BASE
	TIM_TimeBaseStructure.TIM_Period = Timer_Period;
  TIM_TimeBaseStructure.TIM_Prescaler = Timer_Prescaler;
  TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1;
  TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;
	TIM_TimeBaseStructure.TIM_RepetitionCounter=0;

  TIM_TimeBaseInit(TIM3, &TIM_TimeBaseStructure);
	
	//PWM OUT
	
	 /* PWM1 Mode configuration: Channel1 */
  TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;
  TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
  TIM_OCInitStructure.TIM_Pulse = CCR1_Val;
  TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High;

  TIM_OC1Init(TIM3, &TIM_OCInitStructure);

  TIM_OC1PreloadConfig(TIM3, TIM_OCPreload_Enable);

  /* PWM1 Mode configuration: Channel2 */
 //TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
  TIM_OCInitStructure.TIM_Pulse = CCR2_Val;
  TIM_OC2Init(TIM3, &TIM_OCInitStructure);
  TIM_OC2PreloadConfig(TIM3, TIM_OCPreload_Enable);
	
	TIM_ARRPreloadConfig(TIM3, ENABLE); //可有可无

  /* TIM3 enable counter */
  TIM_Cmd(TIM3, ENABLE);
	TIM_CtrlPWMOutputs(TIM3,ENABLE); //开启OC  OCN
	
}

void Timer_Init(void)
{
	Timer_GPIO_Config();
	Timer_Config();
}

void PWM_Set(uint16_t period,uint16_t pluse,uint8_t channle)//freq=周期
{
	TIM_TimeBaseInitTypeDef  TIM_TimeBaseStructure;
	TIM_OCInitTypeDef  TIM_OCInitStructure;
	
	RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE);
	
	//TIME BASE
	TIM_TimeBaseStructure.TIM_Period = period;
  TIM_TimeBaseStructure.TIM_Prescaler = Timer_Prescaler;
  TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1;
  TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;
	TIM_TimeBaseStructure.TIM_RepetitionCounter=0;

  TIM_TimeBaseInit(TIM3, &TIM_TimeBaseStructure);
	

	
		 /* PWM1 Mode configuration: Channel1 */
		TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;
		TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
		
		TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High;
	if(channle==1)
	{
		TIM_OCInitStructure.TIM_Pulse = pluse;
		TIM_OC1Init(TIM3, &TIM_OCInitStructure);
		TIM_OC1PreloadConfig(TIM3, TIM_OCPreload_Enable);
	}
	else if(channle==2)
	{
  /* PWM1 Mode configuration: Channel2 */
	  TIM_OCInitStructure.TIM_Pulse = pluse;
	  TIM_OC2Init(TIM3, &TIM_OCInitStructure);
	  TIM_OC2PreloadConfig(TIM3, TIM_OCPreload_Enable);
	}
	TIM_ARRPreloadConfig(TIM3, ENABLE); 
  /* TIM3 enable counter */
  TIM_Cmd(TIM3, ENABLE);
	TIM_CtrlPWMOutputs(TIM3,ENABLE); //开启OC  OCN
}

四、逻辑分析仪仿真

int main(void)
{
	
	Timer_Init();
	PWM_Set(1000,500,1);
	Delay_Ms(500);
	PWM_Set(3000,900,1);
	while(1)
	{
		
	}
}