一、组网需求
1、如图所示,SwitchA和SwitchB通过以太链路分别都连接VLAN10和VLAN20,且SwitchA和SwitchB之间有较大的数据流量。
用户希望SwitchA和SwitchB之间能够提供较大的链路带宽来使相同VLAN间互相通信。
2、网络拓扑
3、配置思路
采用如下的思路配置负载分担链路聚合:
创建Eth-Trunk接口并加入成员接口,实现增加链路带宽。
创建VLAN并将端口加入VLAN。
配置负载分担方式,实现流量在Eth-Trunk各成员接口间的负载分担,增加可靠性。
二、操作步骤
1、创建eth-trunk并加入成员接口
第一种加入方法:
<Huawei>system-view
[Huawei]sysname SWA
[SWA]interface Eth-Trunk 1
[SWA-Eth-Trunk1]trunkport GigabitEthernet 0/0/1 to 0/0/2
[SWA-Eth-Trunk1]q
第二种加入方法:
<Huawei>system-view
[Huawei]sysname SWB
[SWB]interface Eth-Trunk 1
[SWB-Eth-Trunk1]q
[SWB]interface GigabitEthernet 0/0/1
[SWB-GigabitEthernet0/0/1]eth-trunk 1
[SWB-GigabitEthernet0/0/1]q
[SWB]interface GigabitEthernet 0/0/2
[SWB-GigabitEthernet0/0/2]eth-trunk 1
[SWB-GigabitEthernet0/0/2]q
2、创建vlan并将端口加入vlan,SWB同SWA配置相似
[SWA]vlan batch 10 20
[SWA]interface GigabitEthernet 0/0/4
[SWA-GigabitEthernet0/0/4]port link-type trunk
[SWA-GigabitEthernet0/0/4]port trunk allow-pass vlan 10
[SWA-GigabitEthernet0/0/4]q
[SWA]interface GigabitEthernet 0/0/5
[SWA-GigabitEthernet0/0/5]port link-type trunk
[SWA-GigabitEthernet0/0/5]port trunk allow-pass vlan 20
[SWA-GigabitEthernet0/0/5]q
3、配置eth-trunk接口允许vlan10和vlan20通过,并设置负载分担模式。SWB同SWA配置相似
[SWA]interface Eth-Trunk 1
[SWA-Eth-Trunk1]port link-type trunk
[SWA-Eth-Trunk1]port trunk allow-pass vlan 10 20
[SWA-Eth-Trunk1]load-balance src-dst-mac
[SWA-Eth-Trunk1]q
4、查看配置结果
[SWA]display eth-trunk 1
Eth-Trunk1's state information is:
WorkingMode: NORMAL Hash arithmetic: According to SA-XOR-DA
Least Active-linknumber: 1 Max Bandwidth-affected-linknumber: 8
Operate status: up Number Of Up Port In Trunk: 2
--------------------------------------------------------------------------------
PortName Status Weight
GigabitEthernet0/0/1 Up 1
GigabitEthernet0/0/2 Up 1