1 、 A network administrator was called away from the terminal while using Telnet to monitor a remote router. The Telnet session was left connected. If the default Telnet configuration is used, what will the administrator find upon returning 15 minutes later?

<?xml:namespace prefix = o ns = "urn:schemas-microsoft-com:office:office" />

• The Telnet session entered a "sleep" state and will resume when the spacebar is pressed.
• The Telnet session remained connected and is on the same screen it was left on.
• The Telnet session suspended itself and will resume when the Enter key is pressed.
• The Telnet session terminated itself after 10 minutes of inactivity.
• The Telnet session remained active but now requires the password to be entered again.

2 、 What is the main use of Telnet?

• transfer of data between end users
• verification of simple connectivity
• routing of data packets
• remote connection to network devices

3、
Which of the following is true regarding CDP and the graphic shown?

• CDP running on Router D will gather information about routers A, B, C, and E.
• By default, Router A will receive CDP advertisements from routers B and C.
• If routers D and E are running different routing protocols, they will not exchange CDP information.
• Router E can use CDP to identify the IOS running on Router B.

 
4、Which of the following are displayed by the Router# show cdp neighbors command? (Choose three.)

• load
• platform
• reliability
• holdtime
• local interface

5 、 To obtain CDP information from a Cisco router that is not directly connected to the administrator's console, what must happen?

• The source router must send TLV blocks to the remote router.
• The administrator can Telnet to a Cisco device that is connected to the remote router.
• The administrator needs to issue the Router# show cdp all to view the entire network CDP advertisements.
• The administrator must transmit TTL packets to the remote device and wait for a response.

6 、 What is the purpose of the cdp timer command?

• specifies the hold time to be sent in the CDP update packet
• resets the traffic counters back to zero
• specifies how often the Cisco IOS software sends CDP updates
• deletes and resets the CDP table of information about neighbors

7 、 An administrator is attempting to enable CDP on the interface of a Cisco router. After issuing the command Router(config-if)# cdp enable, the router responds with an error stating that CDP is not active. What might be the problem?

• The cdp enable command must be issued from the global mode prompt.
• The administrator needed to issue the command Router(config-if)# cdp run.
• CDP has not been configured globally.
• The administrator did not manually enter the CDP neighbors into the CDP table.

8、
The traceroute command was used to trace the path between routers A and D. What would an output display of three asterisks (***) indicate?

• The command was issued from the wrong prompt.
• Each datagram was successfully sent.
• One of the routers is unreachable.
• There are three hops between source and destination.

 
9、

Pings between Atlanta and Dallas are successful. If a hostname table or DNS connection is not available, which command will successfully establish a remote connection from <?xml:namespace prefix = st1 ns = "urn:schemas-microsoft-com:office:smarttags" />Atlanta to Dallas via Telnet?

• Atlanta> connect Dallas
• Atlanta> 197.72.3.2
• Atlanta# 206.157.85.1
• Atlanta# telnet Dallas

10 、 How many Telnet sessions can take place simultaneously on a router running a standard edition of the IOS?

• 4
• 5
• 8
• 10

11 、 Why would an administrator use the Telnet application when troubleshooting a network? (Choose three.)

• It can be used to verify the operation of application layer software between the source and destination.
 • Telnet can use the ICMP protocol to verify a hardware connection and network layer address.
• It is the most complete testing mechanism available.
• Remote networks may be accessed via a Telnet session for troubleshooting.
• Time to Live values are used by Telnet to identify a failure of device between source and destination.

12 、 For which three network layer protocols does CDP provide information? (Choose three.)

• IP
• RIP
• SNMP
• AppleTalk
• IPX
• EIGRP

13、
If the network administrator establishes a telnet session from Workstation 2 to GAD and then from GAD to BHM, what occurs if the session with BHM is suspended and the Enter key is pressed?

• The GAD session will be resumed.
• The BHM session will be resumed.
• The GAD session will be terminated.
• The BHM session will be terminated.

14、Transmitting type length values (TLVs) inside advertisements is a process used by CDP to provide information about neighboring devices. What information is displayed by these TLVs? (Choose three.)

• interface information of the connected device
• all networks connected to the neighboring device
• name of the connected device
• routing protocol used on the neighboring device
• holdtime for advertisements

15、
Which command will produce the output shown in the graphic?

• show cdp
• show cdp neighbors
• show cdp neighbors detail
• show cdp detail
• show cdp traffic

 
16、What key sequence is used to suspend a Telnet session on a remote router?
• Ctrl-Shift-S
• Ctrl-Shift-6
• Ctrl-Shift-6, then x
• Ctrl-Alt-S
• Ctrl-Alt-6
• Ctrl-Alt-6, then x

 
17、What command enables CDP on the interface of a router?

• Router(config-if)# cdp enable
• Router(config-if)# cdp run
• Router(config-if)# cdp start
• Router(config-if)# cdp config

18、How can a network administrator logged in to RTA gather information about the Cisco devices that are directly connected to its neighbor, RTB?

• Use the show cdp neighbors detail command on RTA to view information about every device on the entire internetwork.
• Use ping to determine the status of RTB, then issue the show cdp neighbors detail command.
• Use Telnet to connect to RTB, then issue the show cdp neighbors command.
• Use traceroute to establish the pathway to RTB, then issue the show cdp neighbors command.