树莓派有can通信吗_树莓派can通信

This post walks through setting up a CAN controller on the Raspberry Pi. My goal is to help demystify the process, and provide simple instructions that a relative beginner should be able to follow. Particularly, including information that I wish was more readily available when I started with the project.

By the end of this tutorial you should have a working CAN controller connected to the Raspberry Pi via the SPI bus. Using SocketCAN it will be possible to send and receive CAN packets through the Linux IP stack. This means you can analyse CAN packets just as you would with TCP/IP, using standard utilities like tcpdump and Wireshark. Additionally, using utilities like candump/cansend provided by Can-utils, you can remove an extra layer of abstraction, and focus purely on the CAN data layer.

Getting the Hardware

You have a fair amount of choices when it comes to hardware. The most discussed and most popular modules use the MCP2515 CAN-SPI chip, so I‘ll focus on those.

Some options are:

-PICAN by SK Pang Electronics - ￡32.28 Inc VAT (~$46) - Link

-CAN-Bus Sheld by SparkFun - ~$25 - Link

-Ebay - less than $2 (search for "mcp2515 module")

I chose to go with the cheap Ebay module (pictured above), not that the other alternatives weren‘t great. The SparkFun shield looked very interesting with a microSD slot for data logging, and a hookup for GPS, but since I was learning and didn‘t want to end up bricking a nice piece of hardware just yet, I went the cheaper route.

You should be able to follow this guide for the other modules as well, you‘ll just have to determine the wiring by looking at the schematics for your module of choice.

I found some schematics for the Ebay module - PDF

Note, the Ebay module uses the TJA1050 CAN transceiver, while the others use the MCP2551. Not sure if it makes much of a difference, but thought it might be worth noting.

Wiring it Up

This should apply to all the modules I mentioned, though the labeling may be a bit different. pinout.xyz has a super cool interactive RPi pinout for reference.

RPi Pin RPi Label CAN Module

02---------5V------------VCC

06---------GND-----------GND

19---------GPIO10--------MOSI (SI)

21---------GPIO9---------MISO (SO)

22---------GPIO25--------INT

23---------GPIO11--------SCK

24---------GPIO8---------CS

Enabling the SPI Bus and Loading the Kernel Modules

Edit /boot/config.txt and add the following lines, setting the oscillator parameter to that of the oscillator present on the module. Most of the modules use a 16MHz oscillator for the clock, though the Ebay module uses 8MHz oscillator=8000000. You can determine the frequency by looking at the chip.

dtparam=spi=on

dtoverlay=mcp2515-can0,oscillator=16000000,interrupt=25

dtoverlay=spi-bcm2835-overlay

Reboot.

If everything is hooked up and working the can0 interface should be visible with ifconfig can.

[email protected]:~ $ ifconfig can

can0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00

NOARP MTU:16 Metric:1

RX packets:0 errors:0 dropped:0 overruns:0 frame:0

TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:10

RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

The MCP2515 device tree overlay parameters are described in /boot/overlays/README.

Name: mcp2515-can0

Info: Configures the MCP2515 CAN controller on spi0.0

Load: dtoverlay=mcp2515-can0,=

Params: oscillator Clock frequency for the CAN controller (Hz)

spimaxfrequency Maximum SPI frequence (Hz)

interrupt GPIO for interrupt signal

Compiling Can-utils

You may need to install some prerequisites:

sudo apt-get install git autoconf libtool

Run the following commands to compile can-utils:

git clone https://github.com/linux-can/can-utils.git

cd can-utils

./autogen.sh

./configure

make

sudo make install

You may also install via the repository:

sudo apt-get install can-utils

Bring Up the Interface

You can bring up the interface with:

sudo ip link set can0 up type can bitrate 50000

You‘ll need to select the proper bitrate for the network you‘re connecting to. Common bitrates are: 10000, 20000, 50000, 100000, 125000, 250000, 500000, 800000, 1000000.

If you need to change a setting, first bring down the interface:

sudo ip link set can0 down

You can see a list of available settings by appending help to the command:

[email protected]:~ $ ip link set can0 up type can bitrate 50000 help

Usage: ip link set DEVICE type can

[ bitrate BITRATE [ sample-point SAMPLE-POINT] ] |

[ tq TQ prop-seg PROP_SEG phase-seg1 PHASE-SEG1

phase-seg2 PHASE-SEG2 [ sjw SJW ] ]

[ dbitrate BITRATE [ dsample-point SAMPLE-POINT] ] |

[ dtq TQ dprop-seg PROP_SEG dphase-seg1 PHASE-SEG1

dphase-seg2 PHASE-SEG2 [ dsjw SJW ] ]

[ loopback { on | off } ]

[ listen-only { on | off } ]

[ triple-sampling { on | off } ]

[ one-shot { on | off } ]

[ berr-reporting { on | off } ]

[ fd { on | off } ]

[ restart-ms TIME-MS ]

[ restart ]

Where: BITRATE := { 1..1000000 }

SAMPLE-POINT := { 0.000..0.999 }

TQ := { NUMBER }

PROP-SEG := { 1..8 }

PHASE-SEG1 := { 1..8 }

PHASE-SEG2 := { 1..8 }

SJW := { 1..4 }

RESTART-MS := { 0 | NUMBER }

The loopback setting enables loopback mode on the MCP2515, which can be useful for verifying that the RPi is communicating with the CAN module without having to connect to an actual CAN bus. All messages transmitted in loopback mode will be echoed back over the interface.

Listen-only can be useful if you‘re interested in sniffing CAN traffic, and want to lessen the risk of messing something up by ensuring the device doesn‘t send any packets.

Send and Receive CAN Messages

Using cansend/candump it‘s possible to respectively send and receive CAN messages.

Send

cansend can0 001#1122334455667788

And receive:

candump can0

On some cars you may not see any traffic through the CAN-bus on the OBD2 port. This is due to the fact that there is a ‘gateway‘ present between the OBD2 port and the various CAN networks. The gateway acts like a firewall between the networks, and it‘s necessary to send a request for data before it can be received.

原文：https://www.cnblogs.com/chendeqiang/p/12861683.html