基于STM32-基本定时器3的PWM输出 例程（带中文注释 ) ------------(转)

基于STM32-基本定时器3的PWM输出 例程（带中文注释

                               波形图                                   

说明：使用标准库3.4 
#include "stm32f10x.h"
TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
TIM_OCInitTypeDef TIM_OCInitStructure;
uint16_t CCR1_Val = 250;
uint16_t CCR2_Val = 500;
uint16_t CCR3_Val = 750;
uint16_t CCR4_Val = 0;
uint16_t PrescalerValue = 0;

void RCC_Configuration(void);                 //时钟配置
void GPIO_Configuration(void);             //管脚配置
void Delay (__IO uint32_t nCount);         //延时函数

int main(void)
{

RCC_Configuration();
GPIO_Configuration();
PrescalerValue = (uint16_t) (SystemCoreClock / 24000000) - 1;
TIM_TimeBaseStructure.TIM_Period = 1000;                                  //周期
TIM_TimeBaseStructure.TIM_Prescaler = PrescalerValue;              //分频
TIM_TimeBaseStructure.TIM_ClockDivision = 0;                             //时钟分割
TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;
                //计数模式
TIM_TimeBaseInit(TIM3, &TIM_TimeBaseStructure);                    //初始TIM3

/*************************** 通道1 ********************************/
TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM2;    //PWM2
TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;   //PWM功能使能
TIM_OCInitStructure.TIM_Pulse = CCR1_Val;                            //写比较值(占空比
TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_Low;   //置高
TIM_OC1Init(TIM3, &TIM_OCInitStructure);
TIM_OC1PreloadConfig(TIM3, TIM_OCPreload_Enable);

/****************************** 通道2 ******************************/
/* PWM1 Mode configuration: Channel2 */
TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
TIM_OCInitStructure.TIM_Pulse = CCR2_Val;
TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High;
TIM_OC2Init(TIM3, &TIM_OCInitStructure);
TIM_OC2PreloadConfig(TIM3, TIM_OCPreload_Enable);

/******************************* 通道3 *********************************/
/* PWM1 Mode configuration: Channel3 */
TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
TIM_OCInitStructure.TIM_Pulse = CCR3_Val;
TIM_OC3Init(TIM3, &TIM_OCInitStructure);
TIM_OC3PreloadConfig(TIM3, TIM_OCPreload_Enable);

/****************************** 通道4 *********************************/
/* PWM1 Mode configuration: Channel4 */
TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
TIM_OCInitStructure.TIM_Pulse = CCR4_Val;
TIM_OC4Init(TIM3, &TIM_OCInitStructure);
TIM_OC4PreloadConfig(TIM3, TIM_OCPreload_Enable);

TIM_ARRPreloadConfig(TIM3, ENABLE);                        //
TIM_Cmd(TIM3, ENABLE);                                          //使能计数

while (1)
{
CCR4_Val++;
if(CCR4_Val==1000)CCR4_Val=0;
TIM_SetCompare4(TIM3,CCR4_Val);                         //占空比调节

Delay(0xFfff);

}
}

/*************************** 时钟配置 *******************************/
void RCC_Configuration(void)
{
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE);             //T3时钟使能
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB |
                         RCC_APB2Periph_GPIOC | RCC_APB2Periph_AFIO, ENABLE);
               //管脚时钟
}
/************************** 管脚配置 ******************************/              

void GPIO_Configuration(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6 | GPIO_Pin_7;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1;
GPIO_Init(GPIOB, &GPIO_InitStructure);

}
/************************** 延时函数 ******************************/

void Delay (__IO uint32_t nCount)
{
for(; nCount != 0; nCount--);
}