＜RT-Thread＞打开新世界的大门：Kconfig

menu "Hardware Drivers Config"

config SOC_STM32F429ZI
    bool
    select SOC_SERIES_STM32F4
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    default y

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default y
            config BSP_USING_UART3
                bool "Enable UART3"
                default y

            config BSP_UART1_RX_USING_DMA
                bool "Enable UART1 RX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n
	        config BSP_UART1_TX_USING_DMA
		        bool "Enable UART1 TX DMA"
		        depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
		        default n
        endif

    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n

    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI3
                bool "Enable SPI3 BUS"
                default n

            config BSP_SPI3_TX_USING_DMA
                bool "Enable SPI3 TX DMA"
                depends on BSP_USING_SPI3
                default n
                
            config BSP_SPI3_RX_USING_DMA
                bool "Enable SPI3 RX DMA"
                depends on BSP_USING_SPI3
                select BSP_SPI3_TX_USING_DMA
                default n
        endif

    menuconfig BSP_USING_I2C1
        bool "Enable I2C1 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C1
            config BSP_I2C1_SCL_PIN
                int "i2c1 scl pin number"
                range 1 216
                default 22
            config BSP_I2C1_SDA_PIN
                int "I2C1 sda pin number"
                range 1 216
                default 25
        endif

    menuconfig BSP_USING_TIM
        bool "Enable timer"
        default n
        select RT_USING_HWTIMER
        if BSP_USING_TIM
            config BSP_USING_TIM11
                bool "Enable TIM11"
                default n

            config BSP_USING_TIM13
                bool "Enable TIM13"
                default n

            config BSP_USING_TIM14
                bool "Enable TIM14"
                default n
        endif

    menuconfig BSP_USING_PWM
        bool "Enable pwm"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM2
            bool "Enable timer2 output pwm"
            default n
            if BSP_USING_PWM2
                config BSP_USING_PWM2_CH1
                    bool "Enable PWM2 channel1"
                    default n
            endif
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif

    menuconfig BSP_USING_ONCHIP_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        select RT_USING_LIBC
        default n
        if BSP_USING_ONCHIP_RTC
            choice
                prompt "Select clock source"
                default BSP_RTC_USING_LSE

                config BSP_RTC_USING_LSE
                    bool "RTC USING LSE"

                config BSP_RTC_USING_LSI
                    bool "RTC USING LSI"
            endchoice
        endif

    config BSP_USING_WDT
        bool "Enable Watchdog Timer"
        select RT_USING_WDT
        default n

    config BSP_USING_SDIO
        bool "Enable SDIO"
        select RT_USING_SDIO
        select RT_USING_DFS
        default n

    config BSP_USING_FMC
        bool
        default n

    config BSP_USING_LTDC
        bool
        default n
    source "libraries/HAL_Drivers/Kconfig"
    
endmenu

menu "Board extended module Drivers"

endmenu
 
endmenu