OSPF实验2

实验要求

1.如图连接，合理规划IP地址，所有路由器各自创建一个loopback接口

2.R1再创建三个接口IP地址为201.1.1.1/24、201.1.2.1/24、201.1.3.1/24

   R5再创建三个接口IP地址为202.1.1.1/24、202.1.2.1/24、202.1.3.1/24

   R7再创建三个接口IP地址为203.1.1.1/24、203.1.2.1/24、203.1.3.1/24

3.如图运行路由协议

 3.1  R1 -R2  -R3之间使用MGRE网络，为hub-spoke 网络结构，R1为hub端 ，

部署OSPF网络,MGRE修改为BMA网络类型

 3.2  R2 -R3之间启用PPP pap 单向认证，R3-R4之间启用PPP的chap双向认证

4.area  1  区域不得出现4.5类LSA

5.其他区域优先通过R3访问R1 三个环回接口

6.尽量减少路由条目数量

7.area 1 区域增加安全性

8.全网可达

实验步骤

配置IP地址及创建环回接口

R1

[r1]int e 0/0/0
[r1-Ethernet0/0/0]ip add 18.1.1.1 24
[R1]int l 0
[R1-LoopBack0]ip add 1.1.1.1 24
[R1-LoopBack0]int l 1
[R1-LoopBack1]ip add 201.1.1.1 24
[R1-LoopBack1]int l 2
[R1-LoopBack2]ip add 201.1.2.1 24
[R1-LoopBack2]int l 3
[R1-LoopBack3]ip add 201.1.3.1 24

R2

[r2-Ethernet0/0/0]ip add 28.1.1.2 24
[r2-Serial0/0/0]ip add 24.1.1.1 24
[R2-Serial0/0/0]int l 0
[R2-LoopBack0]ip add 2.2.2.2 24

R3

[r3-Ethernet0/0/0]ip add 38.1.1.2 24
[r3-Serial0/0/0]ip add 34.1.1.1 24
[R3-Serial0/0/0]int  l 0
[R3-LoopBack0]ip add 3.3.3.3 24

R4

[r4-Serial0/0/1]ip add 34.1.1.2 24
[r4-Serial0/0/2]ip add 24.1.1.2 24
[r4-Ethernet0/0/0]ip add 45.1.1.1 24
[r4-Ethernet0/0/1]ip add 46.1.1.1 24
[R4-LoopBack0]ip add 4.4.4.4 24

R5

[r5-Ethernet0/0/0]ip add 45.1.1.2 24
[R5-LoopBack0]int l 1
[R5-LoopBack1]ip add 202.1.1.1 24
[R5-LoopBack1]int l 2
[R5-LoopBack2]ip add 202.1.2.1 24
[R5-LoopBack2]int l 3
[R5-LoopBack3]ip add 202.1.3.1 24

R6

[r6-Ethernet0/0/0]ip add 46.1.1.2 24
[r6-Ethernet0/0/1]ip add 67.1.1.1 24
[r6-Ethernet0/0/1]int l 0
[R6-LoopBack0]ip add 6.6.6.6 24

R7

[r7-Ethernet0/0/0]ip add 67.1.1.2 24
[R7-LoopBack0]ip add 7.7.7.7 24
[R7-LoopBack0]int l 1
[R7-LoopBack1]ip add 203.1.1.1 24
[R7-LoopBack1]int l 2
[R7-LoopBack2]ip add 203.1.2.1 24
[R7-LoopBack2]int l 3
[R7-LoopBack3]ip add 203.1.3.1 24

R8

[r8-Ethernet0/0/0]ip add 18.1.1.1 24
[r8-Ethernet0/0/1]ip add 28.1.1.1 24
[r8-GigabitEthernet0/0/0]ip add 38.1.1.1 24
[R8-LoopBack0]ip add 8.8.8.8 24

运行路由协议，R1-R2 -R3之间使用MGRE网络，为hub-spoke 网络结构，R1为hub端，部署OSPF网络，MGRE修改为BMA网络类型。

在R1，R2，R3上写缺省，使三者互通

[R1]ip route-static 0.0.0.0 0 18.1.1.2
[R2]ip route-static 0.0.0.0 0 82.1.1.1
[R3]ip route-static 0.0.0.0 0 83.1.1.1

配置MGRE网络， 创建隧道

R1

[R1]int t0/0/0
[R1-Tunnel0/0/0]ip add 10.1.1.1 24
[R1-Tunnel0/0/0]tunnel-protocol gre p2mp 
[R1-Tunnel0/0/0]source 18.1.1.1
[R1-Tunnel0/0/0]nhrp entry multicast dynamic 
 
[R1-Tunnel0/0/0]nhrp network-id 100  
[R1-Tunnel0/0/0]ospf network-type broadcast 
[R1-Tunnel0/0/0]ospf dr-priority 10

R2

[R2]int t0/0/0
[R2-Tunnel0/0/0]ip add 10.1.1.2 24
[R2-Tunnel0/0/0]tunnel-protocol gre p2mp
[R2-Tunnel0/0/0]source 82.1.1.2
[R2-Tunnel0/0/0]nhrp network-id 100   
[R2-Tunnel0/0/0]nhrp entry 10.1.1.1 18.1.1.1 register
 
[R2-Tunnel0/0/0]ospf network-type broadcast 
[R2-Tunnel0/0/0]ospf dr-priority 0 

R3

[R3]int t0/0/0
[R3-Tunnel0/0/0]ip add 10.1.1.3 24
[R3-Tunnel0/0/0]tunnel-protocol gre p2mp 
[R3-Tunnel0/0/0]source 83.1.1.2
[R3-Tunnel0/0/0]nhrp network-id 100  
[R3-Tunnel0/0/0]nhrp entry 10.1.1.1 18.1.1.1 register 
 
[R3-Tunnel0/0/0]ospf network-type broadcast 
[R3-Tunnel0/0/0]ospf dr-priority 0

部署OSPF网络:

[R1]ospf 100 rou 1.1.1.1
[R1-ospf-100]are 0
[R1-ospf-100-area-0.0.0.0]network 1.1.1.1 0.0.0.0
[R1-ospf-100-area-0.0.0.0]network 201.1.1.1  0.0.0.0
[R1-ospf-100-area-0.0.0.0]network 201.1.2.1 0.0.0.0
[R1-ospf-100-area-0.0.0.0]network 201.1.3.1 0.0.0.0
[R1-ospf-100-area-0.0.0.0]network 10.1.1.1 0.0.0.0

[R2]ospf 100 rou 2.2.2.2
[R2-ospf-100]are 0
[R2-ospf-100-area-0.0.0.0]network 10.1.1.2 0.0.0.0
[R2-ospf-100]are 1
[R2-ospf-100-area-0.0.0.1]network 24.1.1.1 0.0.0.0
[R2-ospf-100-area-0.0.0.1]network 2.2.2.2 0.0.0.0


[R3]ospf 100 rou 3.3.3.3
[R3-ospf-100]are 0
[R3-ospf-100-area-0.0.0.0]network 10.1.1.3 0.0.0.0
[R3-ospf-100]are 1
[R3-ospf-100-area-0.0.0.1]netwrrk 34.1.1.1 0.0.0.0
[R3-ospf-100-area-0.0.0.1]network 3.3.3.3 0.0.0.0

[R4]ospf 100 rou 4.4.4.4
[R4-ospf-100]area 1    
[R4-ospf-100-area-0.0.0.1]network 24.1.1.2 0.0.0.0
[R4-ospf-100-area-0.0.0.1]network 34.1.1.2 0.0.0.0
[R4-ospf-100-area-0.0.0.1]network 4.4.4.4 0.0.0.0
[R4-ospf-100-area-0.0.0.1]area 2
[R4-ospf-100-area-0.0.0.2]network 46.1.1.1 0.0.0.0

[R6]ospf 100 rou 6.6.6.6
[R6-ospf-100]are 2
[R6-ospf-100-area-0.0.0.2]net 6.6.6.6 0.0.0.0
[R6-ospf-100-area-0.0.0.2]net 46.1.1.2 0.0.0.0

配置RIP

[R4]rip 200
[R4-rip-200]version 2
[R4-rip-200]network 45.0.0.0

[R5]rip 200
[R5-rip-200]version 2
[R5-rip-200]network 202.1.1.0
[R5-rip-200]network 202.1.2.0	
[R5-rip-200]network 202.1.3.0	
[R5-rip-200]network 45.0.0.0
[R5-rip-200]network 5.0.0.0

[R6]rip 100
[R6-rip-100]version 2	
[R6-rip-100]network 67.0.0.0

[R7]rip 100
[R7-rip-100]version 2	
[R7-rip-100]network 203.1.1.0	
[R7-rip-100]network 203.1.2.0
[R7-rip-100]network 203.1.3.0
[R7-rip-100]network 67.0.0.0
[R7-rip-100]network 7.0.0.0

pap认证

[r2]aaa
[r2-aaa]local-user abc password cipher 123
[r2-aaa]local-user abc service-type ppp 
[r2-aaa]int s4/0/0
[r2-Serial4/0/0]ppp authentication-mode pap

[r4]int s4/0/0
[r4-Serial4/0/0]ppp pap local-user abc password cipher 123

chap认证

[R3]aaa
[R3-aaa]local-user cba password cipher 123
Info: Add a new user.
[R3-aaa]local-user cba service-type ppp
[R3-aaa]int s4/0/0	
[R3-Serial4/0/0]ppp authentication-mode chap
[R3-Serial4/0/0]q

[R4]int s4/0/0	
[R4-Serial4/0/0]ppp pap local-user abc password cipher 123
[R4-Serial4/0/0]q
[R4]int s4/0/1
[R4-Serial4/0/1]ppp chap user cba
[R4-Serial4/0/1]ppp chap password cipher 123
[R4-Serial4/0/1]int t 0/0/0

其他区域优先通过R3访问R1三个环回接口。在区域边界路由器做汇总时修改开销值，使得通过r2路由器的开销值大于通过r3的

[R2-ospf-100-area-0.0.0.0] abr-summary 1.1.1.0 255.255.252.0 cost 10
[R2-ospf-100-area-0.0.0.0] abr-summary 201.1.0.0 255.255.252.0 cost 10 
[R3-ospf-100-area-0.0.0.0] abr-summary 201.1.0.0 255.255.252.0 cost 5

采用Tunnel解决不规则区域

R2

[R2]int t 0/0/1
[R2-Tunnel0/0/1]ip address 100.1.1.1 24
[R2-Tunnel0/0/1]tunnel-protocol gre
[R2-Tunnel0/0/1]source 2.2.2.2
[R2-Tunnel0/0/1]description 4.4.4.4
[R2-Tunnel0/0/1]ospf enable 100 area 0

R3

[R3]int t0/0/1
[R3-Tunnel0/0/2]ip address 200.1.1.1 24
[R3-Tunnel0/0/2]tunnel-protocol gre        
[R3-Tunnel0/0/2]source 3.3.3.3
[R3-Tunnel0/0/2]description 4.4.4.4
[R3-Tunnel0/0/2]ospf enable 100 area 0

R4

[R4]int t 0/0/0
[R4-Tunnel0/0/1]ip address 100.1.1.2 24
[R4-Tunnel0/0/1]tunnel-protocol gre        
[R4-Tunnel0/0/1]source 4.4.4.4
[R4-Tunnel0/0/1]description 2.2.2.2
[R4-Tunnel0/0/1]ospf enable 100 area 0
[R4]int t0/0/1
[R4-Tunnel0/0/2]ip add 200.1.1.2 24
[R4-Tunnel0/0/2]tunnel-protocol gre
[R4-Tunnel0/0/2]source 4.4.4.4
[R4-Tunnel0/0/2]description 3.3.3.3
[R4-Tunnel0/0/2]ospf enable 100 area 0

在 r1 上用 r1 环回 ping r7 的环回验证全网可达