作者
QQ群：852283276
微信：arm80x86
微信公众号：青儿创客基地
B站：主页 https://space.bilibili.com/208826118
参考
zynqMP GEM 如何配置GT lane
Zynq MPsoc的GEM Ethernet DTS问题
2017.1-2018.3 Zynq UltraScale+ MPSoC: Linux MACB MDIO support for single MAC managing multiple PHYs
PetaLinux - Zynq MPSoC PS-GTR SGMII - fixed link support patch
UBOOT下SGMII网络不通问题
【分享】 MPSoC的GEM通过SGMII直接和其它CPU、switch芯片连接
Zynq UltraScale+ MPSoC - SGMII using PS-GTR
Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit - PING test fails if using non-English OS
AR# 66670 Zynq-7000 SoC - Linux - Macb performance is not equal/comparable in both directions when using “iperf -d”
iperf详细使用方法
GMII,RGMII,SGMII,TBI,RTBI接口信号及时序介绍
PHY88E1111配置Verilog程序
TCI6487采用SGMII口与Marvel 88e1111相连，SGMII回环成功，但是就是发不出数据
6678 88E1111 sgmii link不上
uboot网口调试Marvell phy 88E1111
Marvell 88E1145PHY芯片的初始化配置
Marvell交换芯片88E6321/88E6320驱动总结-硬件篇
Zynq 7000 双网卡配置-内核DTS该如何配置
Cadence Macb Linux Driver for Zynq and Zynq Ultrascale+ MPSoC
Xilinx GMII2RGMII convertor
ZYNQ7035 使用petalinux 2018.02 配置Gmii to Rgmii构成双网卡
AR# 67923 2016.2 PetaLinux Zynq UltraScale+ MPSoC GMII2RGMII on MACB driver
phytool
i.MX6D: AR8033 Ethernet PHY register setting
88e1512 排坑(一)sgmii网口不稳定
88e1512 排坑(二)sgmii网口存在丢包现象
u-boot新驱动
采用设备树net\eth-uclass.c，调用函数uclass_first_device，
int eth_initialize(void)
{
int num_devices = 0;
struct udevice *dev;
eth_common_init();
/*
* Devices need to write the hwaddr even if not started so that Linux
* will have access to the hwaddr that u-boot stored for the device.
* This is accomplished by attempting to probe each device and calling
* their write_hwaddr() operation.
*/
uclass_first_device(UCLASS_ETH, &dev);
if (!dev) {
printf("No ethernet found.\n");
bootstage_error(BOOTSTAGE_ID_NET_ETH_START);
} else {
char *ethprime = env_get("ethprime");
struct udevice *prime_dev = NULL;
if (ethprime)
prime_dev = eth_get_dev_by_name(ethprime);
if (prime_dev) {
eth_set_dev(prime_dev);
eth_current_changed();
} else {
eth_set_dev(NULL);
}
bootstage_mark(BOOTSTAGE_ID_NET_ETH_INIT);
do {
if (num_devices)
printf(", ");
printf("eth%d: %s", dev->seq, dev->name);
if (ethprime && dev == prime_dev)
printf(" [PRIME]");
eth_write_hwaddr(dev);
uclass_next_device(&dev);
num_devices++;
} while (dev);
putc('\n');
}
return num_devices;
}
性能
zynq，TCP发送，绑核105MB/s，不绑核只有80MB/s，加窗108MB/s且速度很稳定，TCP接收可稳定在77MB/s。
root@zynq:~# iperf3 -c 192.168.6.85
Connecting to host 192.168.6.85, port 5201
[ 4] local 192.168.6.195 port 33536 connected to 192.168.6.85 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-1.01 sec 109 MBytes 906 Mbits/sec 0 185 KBytes
[ 4] 1.01-2.01 sec 108 MBytes 905 Mbits/sec 0 191 KBytes
[ 4] 2.01-3.01 sec 108 MBytes 904 Mbits/sec 0 191 KBytes
[ 4] 3.01-4.01 sec 108 MBytes 903 Mbits/sec 0 191 KBytes
[ 4] 4.01-5.01 sec 108 MBytes 902 Mbits/sec 0 191 KBytes
[ 4] 5.01-6.01 sec 108 MBytes 903 Mbits/sec 0 192 KBytes
[ 4] 6.01-7.00 sec 108 MBytes 904 Mbits/sec 0 192 KBytes
[ 4] 7.00-8.00 sec 107 MBytes 903 Mbits/sec 0 235 KBytes
[ 4] 8.00-9.00 sec 108 MBytes 902 Mbits/sec 0 235 KBytes
[ 4] 9.00-10.00 sec 108 MBytes 902 Mbits/sec 0 235 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-10.00 sec 1.05 GBytes 903 Mbits/sec 0 sender
[ 4] 0.00-10.00 sec 1.05 GBytes 903 Mbits/sec receiver
iperf Done.
root@zynq:~# iperf3 -s
-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
Accepted connection from 192.168.6.85, port 38296
[ 5] local 192.168.6.195 port 5201 connected to 192.168.6.85 port 38298
[ ID] Interval Transfer Bandwidth
[ 5] 0.00-1.00 sec 76.4 MBytes 641 Mbits/sec
[ 5] 1.00-2.00 sec 77.6 MBytes 651 Mbits/sec
[ 5] 2.00-3.00 sec 77.6 MBytes 651 Mbits/sec
[ 5] 3.00-4.00 sec 77.7 MBytes 652 Mbits/sec
[ 5] 4.00-5.00 sec 77.7 MBytes 652 Mbits/sec
[ 5] 5.00-6.00 sec 77.7 MBytes 652 Mbits/sec
[ 5] 6.00-7.00 sec 77.8 MBytes 653 Mbits/sec
[ 5] 7.00-8.00 sec 77.6 MBytes 651 Mbits/sec
[ 5] 8.00-9.00 sec 77.9 MBytes 653 Mbits/sec
[ 5] 9.00-10.00 sec 77.8 MBytes 652 Mbits/sec
[ 5] 10.00-10.02 sec 1.38 MBytes 646 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth
[ 5] 0.00-10.02 sec 0.00 Bytes 0.00 bits/sec sender
[ 5] 0.00-10.02 sec 777 MBytes 651 Mbits/sec receiver
zynqmp发送接收都可达108MB/s。
88e1518
米联开发板，百兆网pc直连无法ping通，接交换机就没问题，按道理应该支持网线直连检测啊。
88e1512 sgmii
- GPIO和serdes的初始化一定要放在uboot里
- 第26个寄存器有对于sgmii接口电平的配置，默认值0x42，初始化的时候没有对其进行配置，猜测这个跟sgmii信号质量有关，于是将这个值设为0x47(700mV)
GEM EMIO RGMII
GEM EMIO只能出GMII，这里用到一个Xilinx的IP，GMII-to-RGMII，在米联的开发板上，不连网线，会导致无法搜索到phy，这个应该是硬件问题。米联的硬件上MDIO总线划分有问题和PL的phy共用MDIO总线，导致不能同时使用。
GEM MIO RGMII 1.8v AR8033
PS_MIO_VREF设置RGMII工作电压，配置AR8033的寄存器工作与1.8v，正确配置RX上下拉电阻。
/* Set RGMII IO voltage to 1.8V */
phy_write(dev, 0x1d, 0x1f);
phy_write(dev, 0x1e, 0x8);
macb.probe failed with -16
EMIO出的MDIO总线没有接到phy上，无法获得正确的phy id，导致执行of_mdiobus_register_device而不是of_mdiobus_register_phy，返回-16，
zynqmp GEM SGMII
首先要给88E1111复位信号信号，复位引脚电平 高电平->低电平->高电平保持，低电平要维持10ms以上，可以给15ms，88E1111通过125CLK设置输出检测到了125Mhz时钟，能确定其正常工作。zynqmp的PS自带GTR，可以配置GEM直接从PS-GTR出SGMII，采用88e1111把SGMII转RJ45，但硬件设计时没有把MDIO接到GEM，所以PHY需要配置寄存器，
reg value
0x1b 0x8084
0x16 0x0
0x00 0x8000
问题解决，只需对芯片执行软复位，发起自协商即可，可以从vivado获取example，内有verilog的配置示例，硬件原理图和封装映射错误，导致1000M无法自协商成功，直接卡死，百兆网可以。
双网口zynq eth1初始化失败
2015.2.1手动生成设备树，默认设置has-mdio=1，所以双网卡共享mdio时，eth1需要覆盖数值为0。
双网口内核 kernel oops
petalinux 2015.2.1，使能了双网口，GEM1的设备树没有配置phy node导致，
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 145 (00:0a:02:f2:ab:aa)
macb e000b000.ethernet eth0: attached PHY driver [Atheros 8031 ethernet] (mii_bus:phy_addr=e000b000.etherne:01, irq=-1)
Unable to handle kernel NULL pointer dereference at virtual address 00000028
pgd = 40004000
[00000028] *pgd=00000000
Internal error: Oops - BUG: 17 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.19.0-xilinx #3
Hardware name: Xilinx Zynq Platform
task: 7d82c9c0 ti: 7d84e000 task.ti: 7d84e000
PC is at mutex_lock+0x10/0x4c
LR is at mdiobus_read+0x1c/0x44
pc : [<404893a4>] lr : [<402d1944>] psr: 600d0013
sp : 7d84fd80 ip : 7d84fdd0 fp : 7d9a0500
r10: 7d80d300 r9 : 00000000 r8 : 7d84fdac
r7 : 403a34a8 r6 : 00000002 r5 : 00000028 r4 : 00000028
r3 : 00000000 r2 : 00000002 r1 : 403a34a8 r0 : 00000028
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 18c5387d Table: 3dbb004a DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0x7d84e238)
Stack: (0x7d84fd80 to 0x7d850000)
fd80: 00000000 402d1944 00000000 7d9a0500 00000000 403a34a8 00000000 402d1688
fda0: 00000004 7d9a0000 7d8d2a10 00000000 00000000 00000000 00000000 00000000
fdc0: 00000000 00000000 00000000 00000000 7d9a0000 7d9a0500 00000000 7d9a0000
fde0: 7d80dc80 7d80dc80 00000000 7d80d300 7d9a0500 402d6ce4 7d8d2a00 7d80dc80
fe00: 7d80dc80 403a34a8 00000001 7d9a0000 7d8d2a10 7d8d2a00 7d80dc80 40671b88
fe20: 00000080 7d9a0000 7d9a0520 401060a0 00000000 00000001 00000008 7d9a0500
fe40: 7d8d0300 00000001 00000000 7d9a0520 406cd400 ffffffed 7d8d2a10 406bac38
fe60: 406bac38 00000000 406cd400 40683e94 00000000 40274e10 7d8d2a10 406f4ddc
fe80: 406bac38 402739c8 7d8d2a10 7d8d2a44 406bac38 406abb98 406996e0 40273bb4
fea0: 00000000 406bac38 40273b4c 402722ec 7d80fb5c 7d8b4334 406bac38 00000000
fec0: 7d9d6f00 4027328c 405d13e8 405d13e9 00000000 406bac38 4067150c 00000000
fee0: 406996e0 402740b8 00000000 406bac24 4067150c 40274e88 7db92880 4067150c
ff00: 00000000 400088e0 7d875180 40490c58 406d3f38 40683e70 00000000 400fe5e4
ff20: 405a9292 7d875400 4069d2b8 60000013 000000b4 7ffffe16 00000000 40035990
ff40: 000000b5 00000006 00000006 000000b4 4069d2a0 00000006 000000b5 00000006
ff60: 000000b5 4068ac8c 40683e8c 406cd400 406cd400 40657d3c 00000006 00000006
ff80: 406574fc 7d84e000 00000000 40483968 00000000 00000000 00000000 00000000
ffa0: 00000000 40483970 00000000 4000dd40 00000000 00000000 00000000 00000000
ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffffffff ffffffff
[<404893a4>] (mutex_lock) from [<402d1944>] (mdiobus_read+0x1c/0x44)
[<402d1944>] (mdiobus_read) from [<402d1688>] (get_phy_device+0x130/0x198)
[<402d1688>] (get_phy_device) from [<402d6ce4>] (macb_mii_init+0x1c8/0x308)
[<402d6ce4>] (macb_mii_init) from [<40671b88>] (macb_probe+0x664/0x7d0)
[<40671b88>] (macb_probe) from [<40274e10>] (platform_drv_probe+0x48/0x98)
[<40274e10>] (platform_drv_probe) from [<402739c8>] (driver_probe_device+0x8c/0x1cc)
[<402739c8>] (driver_probe_device) from [<40273bb4>] (__driver_attach+0x68/0x8c)
[<40273bb4>] (__driver_attach) from [<402722ec>] (bus_for_each_dev+0x6c/0x90)
[<402722ec>] (bus_for_each_dev) from [<4027328c>] (bus_add_driver+0xdc/0x1c4)
[<4027328c>] (bus_add_driver) from [<402740b8>] (driver_register+0x8c/0xd0)
[<402740b8>] (driver_register) from [<40274e88>] (__platform_driver_probe+0x20/0x94)
[<40274e88>] (__platform_driver_probe) from [<400088e0>] (do_one_initcall+0x100/0x180)
[<400088e0>] (do_one_initcall) from [<40657d3c>] (kernel_init_freeable+0x110/0x1d4)
[<40657d3c>] (kernel_init_freeable) from [<40483970>] (kernel_init+0x8/0xe4)
[<40483970>] (kernel_init) from [<4000dd40>] (ret_from_fork+0x14/0x34)
Code: e92d4010 e1a04000 f57ff05b f590f000 (e1903f9f)
---[ end trace b13f75501ad3b839 ]---
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
CPU0: stopping
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G D 3.19.0-xilinx #3
Hardware name: Xilinx Zynq Platform
[<400147f0>] (unwind_backtrace) from [<40010d54>] (show_stack+0x10/0x14)
[<40010d54>] (show_stack) from [<40486d38>] (dump_stack+0x80/0xcc)
[<40486d38>] (dump_stack) from [<400131c8>] (ipi_cpu_stop+0x3c/0x6c)
[<400131c8>] (ipi_cpu_stop) from [<400137b0>] (handle_IPI+0x64/0x84)
[<400137b0>] (handle_IPI) from [<400085cc>] (gic_handle_irq+0x54/0x5c)
[<400085cc>] (gic_handle_irq) from [<40011700>] (__irq_svc+0x40/0x74)
Exception stack(0x4068ff60 to 0x4068ffa8)
ff60: ffffffed 00000000 00000000 4001c9c0 4068e000 00000000 00000000 4068ffb0
ff80: 4048def0 7ffffdc0 00000000 ffffffed 00000001 4068ffa8 4000e7d4 4000e7d8
ffa0: 600d0013 ffffffff
[<40011700>] (__irq_svc) from [<4000e7d8>] (arch_cpu_idle+0x2c/0x38)
[<4000e7d8>] (arch_cpu_idle) from [<40048c94>] (cpu_startup_entry+0xcc/0x1e8)
[<40048c94>] (cpu_startup_entry) from [<40657bcc>] (start_kernel+0x324/0x384)
[<40657bcc>] (start_kernel) from [<00008074>] (0x8074)
---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
link up但是ping不通
petalinux 2015.2.1，设备树配phy node配置compatible错误，
ethernet@e000b000 {
compatible = "xlnx,ps7-ethernet-1.00.a";
reg = <0xe000b000 0x1000>;
status = "okay";
interrupts = <0x0 0x16 0x4>;
clocks = <0x1 0x1e 0x1 0x1e 0x1 0xd>;
clock-names = "pclk", "hclk", "tx_clk";
#address-cells = <0x1>;
#size-cells = <0x0>;
phy-mode = "rgmii-id";
xlnx,ptp-enet-clock = <0x69f6bcb>;
local-mac-address = [00 0a 35 00 1e 53];
xlnx,has-mdio = <0x1>;
phy-handle = <0x4>;
mdio {
#address-cells = <0x1>;
#size-cells = <0x0>;
phy@1 {
compatible = "atheros, at803x";
device_type = "ethernet-phy";
reg = <0x1>;
reset-gpio = <0x5 0x2f 0x0>;
linux,phandle = <0x4>;
phandle = <0x4>;
};
phy@3 {
compatible = "atheros, at803x";
device_type = "ethernet-phy";
reg = <0x3>;
linux,phandle = <0x6>;
phandle = <0x6>;
};
};
};
fixed phy
ti-linux-kernel的cpsw驱动不支持fixed-link
I.MX6 PHY fixup 调用流程 hacking
ping不通，内核打印，FPGA时钟设置不对，重新设置设备树的时钟源，为0，是因为fsbl设置的0
xemacps e000c000.ethernet: Set clk to 0 Hz
xemacps e000c000.ethernet: link up (1000/FULL)
设备树，
fixed-link {
reg = <1>;
full-duplex = <1>; /*0 1*/
speed = <1000>; /*10 100 1000*/
pause = <0>; /*0 1*/
asym-pause = <0>; /*0 1*/
autoneg = <0>; /*0 1*/
duplex = <1>; /*0 1*/
}
zynq uboot下超时
在百兆网时经常出现这个问题，
zynq-uboot> run update_boot
Gem.e000b000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
Gem.e000b000: No link, phyaddr: 1.
Gem.e000b000:1 is connected to Gem.e000b000. Reconnecting to Gem.e000b000
Gem.e000b000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
Gem.e000b000: No link, phyaddr: 1.
Gem.e000b000 Waiting for PHY auto negotiation to complete.....user interrupt!
Gem.e000b000: No link, phyaddr: 3.
增大uboot自协商超时时间。
#define PHY_ANEG_TIMEOUT 16000
tftp超时，时断时续，编辑uboot tftp.c下相关时间宏定义。
AR8033初始化错误导致linux ping不通
petalinux 2015.2.1，wireshark调试，实际情况是包根本没有发出去，在emmc做rootfs时出现，原因不明，参考uboot在驱动中加上下面的补丁。
static int at803x_config_init(struct phy_device *phydev)
{
int ret;
/*printk("%s %d\n", __FUNCTION__, __LINE__);*/
#if 1
/*mwm193 rd rootfs ok, emmc rootfs net ping failed*/
{
int regval;
phy_write(phydev, 0xd, 0x0007);
phy_write(phydev, 0xe, 0x8016);
phy_write(phydev, 0xd, 0x4007);
regval = phy_read(phydev, 0xe);
phy_write(phydev, 0xe, (regval|0x0018));
phy_write(phydev, 0x1d, 0x05);
regval = phy_read(phydev, 0x1e);
phy_write(phydev, 0x1e, (regval|0x0100));
}
#endif
...
}
20190815更新，
if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID ||
phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) {
ret = phy_write(phydev, AT803X_DEBUG_ADDR,
0x0);
if (ret)
return ret;
ret = phy_write(phydev, AT803X_DEBUG_DATA,
BIT(15));
if (ret)
return ret;
}
if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID ||
phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) {
ret = phy_write(phydev, AT803X_DEBUG_ADDR,
AT803X_DEBUG_SYSTEM_MODE_CTRL);
if (ret)
return ret;
ret = phy_write(phydev, AT803X_DEBUG_DATA,
AT803X_DEBUG_RGMII_TX_CLK_DLY);
if (ret)
return ret;
}
budget exhausted after napi reschedule
打印来自napi_poll函数，目前不影响使用，
/* Some drivers may have called napi_schedule
* prior to exhausting their budget.
*/
if (unlikely(!list_empty(&n->poll_list))) {
pr_warn_once("%s: Budget exhausted after napi rescheduled\n",
n->dev ? n->dev->name : "backlog");
goto out_unlock;
}
skbuff: skb_over_panic: text:403b43dc len:2050 put:2050 head:79e53300 data:79e53340 tail:0x79e53b42
错误发生在xemacps驱动中，
[ 7.716894] skbuff: skb_over_panic: text:403b43dc len:2050 put:2050 head:79e53300 data:79e53340 tail:0x79e53b42 end:0x79e53940 dev:eth0
[ 11.606249] xemacps e000b000.ethernet: Set clk to 124999999 Hz
[ 11.611998] xemacps e000b000.ethernet: link up (1000/FULL)
[ 67.715381] INFO: rcu_preempt self-detected stall on CPU { 0} (t=6001 jiffies g=-163 c=-164 q=3)
[ 67.724162] Task dump for CPU 0:
[ 67.727373] dropbearkey R running 0 1030 1028 0x00000002
[ 67.733742] [<400147f0>] (unwind_backtrace) from [<40010d54>] (show_stack+0x10/0x14)
[ 67.741448] [<40010d54>] (show_stack) from [<40056208>] (rcu_dump_cpu_stacks+0x74/0x98)
[ 67.749432] [<40056208>] (rcu_dump_cpu_stacks) from [<40058c0c>] (rcu_check_callbacks+0x224/0x628)
[ 67.758372] [<40058c0c>] (rcu_check_callbacks) from [<4005b150>] (update_process_times+0x30/0x5c)
[ 67.767232] [<4005b150>] (update_process_times) from [<40068580>] (tick_sched_timer+0x44/0x84)
[ 67.775819] [<40068580>] (tick_sched_timer) from [<4005b8e0>] (__run_hrtimer.isra.24+0x6c/0xa4)
[ 67.784497] [<4005b8e0>] (__run_hrtimer.isra.24) from [<4005bf04>] (hrtimer_interrupt+0x124/0x284)
[ 67.793438] [<4005bf04>] (hrtimer_interrupt) from [<40014130>] (twd_handler+0x2c/0x38)
[ 67.801339] [<40014130>] (twd_handler) from [<4005308c>] (handle_percpu_devid_irq+0x68/0x84)
[ 67.809755] [<4005308c>] (handle_percpu_devid_irq) from [<4004fbc8>] (generic_handle_irq+0x20/0x30)
[ 67.818781] [<4004fbc8>] (generic_handle_irq) from [<4004fe8c>] (__handle_domain_irq+0x8c/0xb4)
[ 67.827461] [<4004fe8c>] (__handle_domain_irq) from [<400085b0>] (gic_handle_irq+0x38/0x5c)
[ 67.835797] [<400085b0>] (gic_handle_irq) from [<40011700>] (__irq_svc+0x40/0x74)
[ 67.843253] Exception stack(0x768c7e28 to 0x768c7e70)
[ 67.848292] 7e20: 0000007b 600d0113 00000101 768c6000 79e53b42 79e53340
[ 67.856452] 7e40: 79e53300 407cd469 72c31a00 00000000 79ea758c 72c30b80 00000000 768c7e70
[ 67.864607] 7e60: 404c8edc 404c8edc 200d0113 ffffffff
[ 67.869656] [<40011700>] (__irq_svc) from [<404c8edc>] (skb_panic+0x4c/0x58)
[ 67.876681] [<404c8edc>] (skb_panic) from [<404c8f20>] (skb_put+0x38/0x44)
[ 67.883539] [<404c8f20>] (skb_put) from [<403b43dc>] (xemacps_rx_poll+0x198/0x368)
[ 67.891096] [<403b43dc>] (xemacps_rx_poll) from [<404d5f9c>] (net_rx_action+0xdc/0x24c)
[ 67.899076] [<404d5f9c>] (net_rx_action) from [<40023734>] (__do_softirq+0xd4/0x1b8)
[ 67.906797] [<40023734>] (__do_softirq) from [<40023a20>] (irq_exit+0x58/0xc0)
[ 67.914001] [<40023a20>] (irq_exit) from [<4004fe90>] (__handle_domain_irq+0x90/0xb4)
[ 67.921812] [<4004fe90>] (__handle_domain_irq) from [<400085b0>] (gic_handle_irq+0x38/0x5c)
[ 67.930147] [<400085b0>] (gic_handle_irq) from [<400119c4>] (__irq_usr+0x44/0x60)
修改，
//added this patch to the function xemacps_rx(), just before skb_put() is called:
if ((skb->tail\+len) > skb->end) {
dev_err(&lp->pdev->dev, "skb length error %u\n", len);
dev_kfree_skb(new_skb);
numbdfree = 0xFFFFFFFF;
break;
}
//Apparently the Ethernet interface isn’t fully up when DHCP begins (this is likely the cause of a malformed receive packet that caused the skb_put() issue in the first place). So I modified the /etc/network/interfaces file to set the udhcpc option to retry 10 times instead of 3:
# Wired or wireless interfaces
auto eth0
iface eth0 inet dhcp
udhcpc_opts -t 10
phytool
直接敲phytool输出帮助，phytool -h会报错error: bad location format，
root@zynq:~# phytool print eth0/0
ieee-phy: id:0x02430c54
ieee-phy: reg:BMCR(0x00) val:0x3100
flags: -reset -loopback +aneg-enable -power-down -isolate -aneg-restart -collision-test
speed: 100-full
ieee-phy: reg:BMSR(0x01) val:0x786d
capabilities: -100-b4 +100-f +100-h +10-f +10-h -100-t2-f -100-t2-h
flags: -ext-status +aneg-complete -remote-fault +aneg-capable +link -jabber +ext-register
root@zynq:~# phytool
Usage: phytool read IFACE/ADDR/REG
phytool write IFACE/ADDR/REG <0-0xffff>
phytool print IFACE/ADDR[/REG]
where
ADDR := C22 | C45
C22 := <0-0x1f>
C45 := <0-0x1f>:<0-0x1f>
REG := <0-0x1f>
Examples:
phytool read eth0/0:3/1
phytool write eth0/0xa/0 0x1140
phytool print eth0/0x1c
848
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
