Demo 1# 启动信息2302091600

NOTICE:  Reset status: Power-On Reset
NOTICE:  BL2: v2.5(release):bsp32.0-2.5-dirty
NOTICE:  BL2: Built : 16:14:01, Mar 18 2022
NOTICE:  BL2: Booting BL31


U-Boot 2020.04+g7cc85e1885 (Mar 21 2022 - 08:09:34 +0000)

CPU:   NXP S32G274A rev. 2.1.0
Model: NXP S32G274A-RDB2
DRAM:  3.5 GiB
MMC:   FSL_SDHC: 0
Loading Environment from MMC... OK
Using external clock for PCIe0, CRNS
Configuring PCIe0 as RootComplex(x2)
WARNING: Failed to lock PCIe0 MPLLs
Using external clock for PCIe1, CRNS
Frequency 125Mhz configured for PCIe1
Configuring PCIe1 as SGMII(x2) [XPCS0 1G, XPCS1 1G]
XPCS0 power-up good failed
XPCS1 power-up good failed
XPCS0 pre power-up soft reset failed
XPCS0 power-up failed
XPCS1 pre power-up soft reset failed
XPCS1 power-up failed
PCIe0: Not configuring PCIe, PHY not configured
PCIe1: Not configuring PCIe, PHY not configured
In:    serial@401C8000
Out:   serial@401C8000
Err:   serial@401C8000
Board revision: RDB2/GLDBOX Revision D
Net:   EQOS phy: rgmii @ 1

Warning: eth_eqos (eth0) using random MAC address - 4e:62:a2:31:11:e8
eth0: eth_eqosFailed to set the frequency of mac0_tx_sgmii
Failed to set the frequency of mac0_rx_sgmii
Failed to enable mac0_rx_sgmii clock
Failed to enable mac0_tx_sgmii clock
Failed to set the frequency of mac1_tx_sgmii
Failed to set the frequency of mac1_rx_sgmii
Failed to enable mac1_rx_sgmii clock
Failed to enable mac1_tx_sgmii clock
 PFE: emac0: sgmii emac1: sgmii emac2: rgmii
Structure length mismatch: found 0 required 176
, eth1: eth_pfeng
Hit any key to stop autoboot:  0 
 PFE: emac0: sgmii emac1: sgmii emac2: rgmii
Failed to set the frequency of mac0_tx_sgmii
Failed to set the frequency of mac0_rx_sgmii
Failed to enable mac0_rx_sgmii clock
Failed to enable mac0_tx_sgmii clock
Failed to set the frequency of mac1_tx_sgmii
Failed to set the frequency of mac1_rx_sgmii
Failed to enable mac1_rx_sgmii clock
Failed to enable mac1_tx_sgmii clock
 PFE: emac0: sgmii emac1: sgmii emac2: rgmii
switch to partitions #0, OK
mmc0 is current device
13826056 bytes read in 600 ms (22 MiB/s)
Booting from mmc ...
43396 bytes read in 15 ms (2.8 MiB/s)
## Flattened Device Tree blob at 83e00000
   Booting using the fdt blob at 0x83e00000
   Loading Device Tree to 000000009fff2000, end 000000009ffff983 ... OK
DT: Enabling PFE
DT: Enabling PFE_EMAC_0
DT: pfe0 set to 00:01:be:be:ef:11
DT: pfe0: Update fixed-link speed to 1000Mbps
DT: Enabling PFE_EMAC_1
DT: pfe1 set to 00:01:be:be:ef:22
DT: pfe1: update phy addr to 0x8
DT: Enabling PFE_EMAC_2
DT: pfe2 set to 00:01:be:be:ef:33

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.10.90-rt60+g47a49b91d4d4 (oe-user@oe-host) (aarch64-fsl-linux-gcc (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35.1) #1 SMP PREEMPT Fri Mar 18 14:07:29 UTC 2022
[    0.000000] Machine model: Freescale S32G274
[    0.000000] earlycon: linflex0 at MMIO 0x00000000401c8000 (options '115200n8')
[    0.000000] printk: bootconsole [linflex0] enabled
[    0.000000] Reserved memory: created DMA memory pool at 0x0000000083200000, size 3 MiB
[    0.000000] OF: reserved mem: initialized node pfebufs@83200000, compatible id shared-dma-pool
[    0.000000] Reserved memory: created DMA memory pool at 0x0000000083600000, size 1 MiB
[    0.000000] OF: reserved mem: initialized node pfebufs@83600000, compatible id shared-dma-pool
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000080000000-0x00000000ffffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   [mem 0x0000000100000000-0x00000008dfffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000080000000-0x0000000082ffffff]
[    0.000000]   node   0: [mem 0x0000000083000000-0x00000000835dffff]
[    0.000000]   node   0: [mem 0x00000000835e0000-0x00000000835fffff]
[    0.000000]   node   0: [mem 0x0000000083600000-0x00000000837dffff]
[    0.000000]   node   0: [mem 0x00000000837e0000-0x0000000083ffffff]
[    0.000000]   node   0: [mem 0x0000000084000000-0x000000008407ffff]
[    0.000000]   node   0: [mem 0x0000000084080000-0x00000000bfffffff]
[    0.000000]   node   0: [mem 0x00000000c0000000-0x00000000c03fffff]
[    0.000000]   node   0: [mem 0x00000000c0400000-0x00000000cfffffff]
[    0.000000]   node   0: [mem 0x00000000d0000000-0x00000000d03fffff]
[    0.000000]   node   0: [mem 0x00000000d0400000-0x00000000ffffffff]
[    0.000000]   node   0: [mem 0x0000000880000000-0x00000008dfffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000008dfffffff]
[    0.000000] On node 0 totalpages: 917504
[    0.000000]   DMA zone: 7168 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 524288 pages, LIFO batch:63
[    0.000000]   Normal zone: 5376 pages used for memmap
[    0.000000]   Normal zone: 393216 pages, LIFO batch:63
[    0.000000] cma: Reserved 256 MiB at 0x00000000ef800000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.2
[    0.000000] percpu: Embedded 17 pages/cpu s30744 r8192 d30696 u69632
[    0.000000] pcpu-alloc: s30744 r8192 d30696 u69632 alloc=17*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: ARM erratum 845719
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] CPU features: detected: ARM errata 1165522, 1319367, 1530923, or 1530924
[    0.000000] CPU features: detected: NXP erratum ERR050481 (TLBI handled incorrectly)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 904960
[    0.000000] Kernel command line: console=ttyLF0,115200 root=/dev/mmcblk0p2 rootwait rw earlycon nohz=off coherent_pool=64M
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: mapped [mem 0x00000000eb800000-0x00000000ef800000] (64MB)
[    0.000000] Memory: 3238088K/3670016K available (8638K kernel code, 638K rwdata, 2828K rodata, 1344K init, 239K bss, 169784K reserved, 262144K cma-reserved)
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000]  Trampoline variant of Tasks RCU enabled.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: 544 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] GICv3: MBI range [167:182]
[    0.000000] GICv3: Using MBI frame 0x0000000050800000
[    0.000000] GICv3: 16 PPIs implemented
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000050880000
[    0.000000] ITS: No ITS available, not enabling LPIs
[    0.000000] random: get_random_bytes called from start_kernel+0x31c/0x4ec with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 5.00MHz (virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x127350b88, max_idle_ns: 440795202120 ns
[    0.000001] sched_clock: 56 bits at 5MHz, resolution 200ns, wraps every 4398046511100ns
[    0.008535] Console: colour dummy device 80x25
[    0.012579] Calibrating delay loop (skipped), value calculated using timer frequency.. 10.00 BogoMIPS (lpj=20000)
[    0.022791] pid_max: default: 32768 minimum: 301
[    0.027548] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.034788] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.044034] rcu: Hierarchical SRCU implementation.
[    0.049012] smp: Bringing up secondary CPUs ...
[    0.053742] Detected VIPT I-cache on CPU1
[    0.057348] GICv3: CPU1: found redistributor 1 region 0:0x00000000508a0000
[    0.064227] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.071325] Detected VIPT I-cache on CPU2
[    0.074927] GICv3: CPU2: found redistributor 100 region 0:0x00000000508c0000
[    0.081973] CPU2: Booted secondary processor 0x0000000100 [0x410fd034]
[    0.089089] Detected VIPT I-cache on CPU3
[    0.092675] GICv3: CPU3: found redistributor 101 region 0:0x00000000508e0000
[    0.099712] CPU3: Booted secondary processor 0x0000000101 [0x410fd034]
[    0.106311] smp: Brought up 1 node, 4 CPUs
[    0.110305] SMP: Total of 4 processors activated.
[    0.114978] CPU features: detected: 32-bit EL0 Support
[    0.120113] CPU features: detected: CRC32 instructions
[    0.137356] CPU: All CPU(s) started at EL1
[    0.141042] alternatives: patching kernel code
[    0.146234] devtmpfs: initialized
[    0.155275] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.164619] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.181865] pinctrl core: initialized pinctrl subsystem
[    0.187411] NET: Registered protocol family 16
[    0.193221] DMA: preallocated 4096 KiB GFP_KERNEL pool for atomic allocations
[    0.201189] DMA: preallocated 4096 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.209839] DMA: preallocated 4096 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.217847] thermal_sys: Registered thermal governor 'step_wise'
[    0.218199] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.230671] ASID allocator initialised with 65536 entries
[    0.236015] Serial: AMBA PL011 UART driver
[    0.240765] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[    0.246923] arm-scmi firmware:scmi: No. of Protocol > MAX_PROTOCOLS_IMP
[    0.253457] arm-scmi firmware:scmi: SCMI Protocol v2.0 'NXP:S32G274A' Firmware version 0x0
[    0.284485] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.290783] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.297456] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.304162] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    0.314728] scmi-clocks scmi_dev.1: failed to register clock 85
[    0.320254] scmi-clocks scmi_dev.1: failed to register clock 86
[    0.326131] scmi-clocks scmi_dev.1: failed to register clock 87
[    0.332029] scmi-clocks scmi_dev.1: failed to register clock 88
[    0.338019] scmi-clocks scmi_dev.1: failed to register clock 93
[    0.343836] scmi-clocks scmi_dev.1: failed to register clock 94
[    0.349738] scmi-clocks scmi_dev.1: failed to register clock 95
[    0.355641] scmi-clocks scmi_dev.1: failed to register clock 96
[    0.366290] vgaarb: loaded
[    0.368760] SCSI subsystem initialized
[    0.372500] usbcore: registered new interface driver usbfs
[    0.377818] usbcore: registered new interface driver hub
[    0.383105] usbcore: registered new device driver usb
[    0.388714] pps_core: LinuxPPS API ver. 1 registered
[    0.393250] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.402371] PTP clock support registered
[    0.407255] clocksource: Switched to clocksource arch_sys_counter
[    0.419278] NET: Registered protocol family 2
[    0.423429] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.432427] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[    0.440630] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.448669] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)
[    0.456298] TCP: Hash tables configured (established 32768 bind 32768)
[    0.462565] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[    0.469172] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[    0.476446] NET: Registered protocol family 1
[    0.481040] RPC: Registered named UNIX socket transport module.
[    0.486532] RPC: Registered udp transport module.
[    0.491215] RPC: Registered tcp transport module.
[    0.495901] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.502331] PCI: CLS 0 bytes, default 64
[    0.506984] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    0.515836] workingset: timestamp_bits=62 max_order=20 bucket_order=0
[    0.522687] fuse: init (API version 7.32)
[    0.526424] NET: Registered protocol family 38
[    0.530734] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.538080] io scheduler mq-deadline registered
[    0.542590] io scheduler kyber registered
[    0.547796] s32g-siul2-pinctrl 4009c240.siul2-pinctrl0: initialized s32 pinctrl driver
[    0.555649] s32g-siul2-pinctrl 44010400.siul2-pinctrl1: initialized s32 pinctrl driver
[    0.563827] gpio-24 (sja1110-rst-phy-t1): hogged as output/low
[    0.569257] gpio-81 (sja1110-rst-core): hogged as output/low
[    0.579008] serial: Freescale linflex driver
[    0.592660] printk: console [ttyLF0] enabled0x401c8000 (irq = 36, base_baud = 7812500) is a FSL_LINFLEX
[    0.592660] printk: console [ttyLF0] enabled
[    0.601351] printk: bootconsole [linflex0] disabled
[    0.601351] printk: bootconsole [linflex0] disabled
[    0.611741] 401cc000.serial: ttyLF1 at MMIO 0x401cc000 (irq = 37, base_baud = 7812500) is a FSL_LINFLEX
[    0.621750] 402bc000.serial: ttyLF2 at MMIO 0x402bc000 (irq = 58, base_baud = 7812500) is a FSL_LINFLEX
[    0.632881] fsl_fccu 4030c000.fccu: FCCU status is 0 (normal)
[    0.643801] spi-nor spi0.0: mx25uw51245g (65536 Kbytes)
[    0.651139] libphy: Fixed MDIO Bus: probed
[    0.655676] vcan: Virtual CAN interface driver
[    0.660212] slcan: serial line CAN interface driver
[    0.665188] slcan: 10 dynamic interface channels.
[    0.669984] CAN device driver interface
[    0.674944] flexcan 401b4000.flexcan: device registered (reg_base=(____ptrval____), irq(s):
[    0.683466] flexcan 401b4000.flexcan:  28
[    0.687562] flexcan 401b4000.flexcan:  29
[    0.691651] flexcan 401b4000.flexcan:  30
[    0.695737] flexcan 401b4000.flexcan:  31
[    0.699823] flexcan 401b4000.flexcan: )
[    0.704615] flexcan 401be000.flexcan: device registered (reg_base=(____ptrval____), irq(s):
[    0.713133] flexcan 401be000.flexcan:  32
[    0.717219] flexcan 401be000.flexcan:  33
[    0.721305] flexcan 401be000.flexcan:  34
[    0.725391] flexcan 401be000.flexcan:  35
[    0.729477] flexcan 401be000.flexcan: )
[    0.733985] e100: Intel(R) PRO/100 Network Driver
[    0.738791] e100: Copyright(c) 1999-2006 Intel Corporation
[    0.744431] e1000: Intel(R) PRO/1000 Network Driver
[    0.749408] e1000: Copyright (c) 1999-2006 Intel Corporation.
[    0.755298] e1000e: Intel(R) PRO/1000 Network Driver
[    0.760355] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    0.766417] igb: Intel(R) Gigabit Ethernet Network Driver
[    0.771917] igb: Copyright (c) 2007-2014 Intel Corporation.
[    0.778308] s32cc-dwmac 4033c000.ethernet: IRQ eth_wake_irq not found
[    0.784878] s32cc-dwmac 4033c000.ethernet: IRQ eth_lpi not found
[    0.791197] s32cc-dwmac 4033c000.ethernet: no reset control found
[    0.797495] s32cc-dwmac 4033c000.ethernet: phy mode set to RGMII
[    0.803749] s32cc-dwmac 4033c000.ethernet: User ID: 0x10, Synopsys ID: 0x51
[    0.810852] s32cc-dwmac 4033c000.ethernet:   DWMAC4/5
[    0.815917] s32cc-dwmac 4033c000.ethernet: DMA HW capability register supported
[    0.823365] s32cc-dwmac 4033c000.ethernet: RX Checksum Offload Engine supported
[    0.830812] s32cc-dwmac 4033c000.ethernet: TX Checksum insertion supported
[    0.837818] s32cc-dwmac 4033c000.ethernet: Wake-Up On Lan supported
[    0.844254] s32cc-dwmac 4033c000.ethernet: Enabled workarounds for s32g274a platform
[    0.852149] s32cc-dwmac 4033c000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    0.860136] s32cc-dwmac 4033c000.ethernet: device MAC address aa:58:f1:d7:9e:6b
[    0.867586] s32cc-dwmac 4033c000.ethernet: Enabled Flow TC (entries=8)
[    0.874250] s32cc-dwmac 4033c000.ethernet: Enabling HW TC (entries=256, max_off=256)
[    0.882142] s32cc-dwmac 4033c000.ethernet: SPH feature enabled
[    0.888085] s32cc-dwmac 4033c000.ethernet: Using 32 bits DMA width
[    0.894857] libphy: stmmac: probed
[    0.905117] uio_hse 40211000.mu1b: firmware not found
[    0.910502] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.917162] ehci-pci: EHCI PCI platform driver
[    0.921878] usbcore: registered new interface driver uas
[    0.927330] usbcore: registered new interface driver usb-storage
[    0.935978] s32gen1-rtc 40060000.rtc: registered as rtc0
[    0.941429] s32gen1-rtc 40060000.rtc: setting system clock to 1970-01-01T00:00:00 UTC (0)
[    0.949836] i2c /dev entries driver
[    0.954093] sac58r-wdt 4010c000.swt: SAC58R/S32GEN1 Watchdog Timer Registered. timeout=30s (nowayout=0)
[    0.963997] sac58r-wdt 40200000.swt: SAC58R/S32GEN1 Watchdog Timer Registered. timeout=30s (nowayout=0)
[    0.973806] sac58r-wdt 40204000.swt: SAC58R/S32GEN1 Watchdog Timer Registered. timeout=30s (nowayout=0)
[    0.983598] sac58r-wdt 40208000.swt: SAC58R/S32GEN1 Watchdog Timer Registered. timeout=30s (nowayout=0)
[    0.993546] sdhci: Secure Digital Host Controller Interface driver
[    0.999844] sdhci: Copyright(c) Pierre Ossman
[    1.004281] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.010464] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[    1.017448] hse 40210000.mu0b: firmware not found
[    1.022553] usbcore: registered new interface driver usbhid
[    1.028252] usbhid: USB HID core driver
[    1.039263] mmc0: SDHCI controller on 402f0000.usdhc [402f0000.usdhc] using ADMA
[    1.043668] s32-adc 401f8000.adc: Device initialized successfully.
[    1.075625] s32-adc 402e8000.adc: Device initialized successfully.
[    1.082340] nxp_s32_ddr_perf 403e0000.ddr-perf: probing device
[    1.088754] nxp_s32_ddr_perf 403e0000.ddr-perf: device initialized successfully
[    1.096355] s32-siul2-nvmem 4009c000.nvram: initialize s32 siul2 nvmem driver
[    1.103793] s32-siul2-nvmem 44010000.nvram: initialize s32 siul2 nvmem driver
[    1.111661] NET: Registered protocol family 10
[    1.117086] Segment Routing with IPv6
[    1.120922] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    1.127485] NET: Registered protocol family 17
[    1.132173] mmc0: new high speed SDHC card at address 5048
[    1.132199] can: controller area network core
[    1.138336] mmcblk0: mmc0:5048 SD32G 29.7 GiB 
[    1.142261] NET: Registered protocol family 29
[    1.151345] can: raw protocol
[    1.151356]  mmcblk0: p1 p2
[    1.154367] can: broadcast manager protocol
[    1.161465] can: netlink gateway - max_hops=1
[    1.165952] 8021q: 802.1Q VLAN Support v1.8
[    1.170419] printk: console [ttyLF0]: printing thread started
[    1.176935] pca953x 0-0022: using AI
[    1.686558] rtc-pcf85063 0-0051: registered as rtc1
[    1.686601] i2c i2c-0: IMX I2C adapter registered
[    1.686651] i2c i2c-0: using dma0chan4 (tx) and dma0chan5 (rx) for DMA transfers
[    1.687541] i2c i2c-2: IMX I2C adapter registered
[    1.687594] i2c i2c-2: using dma1chan18 (tx) and dma1chan19 (rx) for DMA transfers
[    1.688399] i2c i2c-4: IMX I2C adapter registered
[    1.688442] i2c i2c-4: using dma1chan20 (tx) and dma1chan21 (rx) for DMA transfers
[    1.689143] phy-s32gen1-serdes 40480000.serdes: Using mode 0 for SerDes subsystem
[    1.689549] phy-s32gen1-serdes 44180000.serdes: Using mode 3 for SerDes subsystem
[    1.989625] phy-s32gen1-serdes 44180000.serdes: XPCS1 power good timeout
[    2.289714] phy-s32gen1-serdes 44180000.serdes: XPCS0 power good timeout
[    2.589764] phy-s32gen1-serdes 44180000.serdes: XPCS1 is in reset
[    2.589774] phy-s32gen1-serdes 44180000.serdes: XPCS init failed
[    2.590018] s32gen1-pcie 40400000.pcie: Configured as RootComplex
[    2.591480] phy-s32gen1-serdes 40480000.serdes: Failed to lock PCIE phy
[    2.591487] phy phy-40480000.serdes.0: phy poweron failed --> -110
[    2.591493] s32gen1-pcie 40400000.pcie: Failed to power on 'serdes_lane0' PHY
[    2.591499] s32gen1-pcie 40400000.pcie: failed to set common PCIe settings
[    2.591766] s32gen1-pcie: probe of 40400000.pcie failed with error -110
[    2.604811] ci_hdrc ci_hdrc.0: EHCI Host Controllerolarity defined
[    2.604996] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
[    2.619255] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[    2.619432] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    2.619442] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.619449] usb usb1: Product: EHCI Host Controller
[    2.619455] usb usb1: Manufacturer: Linux 5.10.90-rt60+g47a49b91d4d4 ehci_hcd
[    2.619460] usb usb1: SerialNumber: ci_hdrc.0
[    2.619885] hub 1-0:1.0: USB hub found
[    2.619913] hub 1-0:1.0: 1 port detected
[    2.686246] EXT4-fs (mmcblk0p2): recovery complete
[    2.687283] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    2.687357] VFS: Mounted root (ext4 filesystem) on device 179:2.
[    2.688029] devtmpfs: mounted
[    2.688666] Freeing unused kernel memory: 1344K
[    2.751370] Run /sbin/init as init process
INIT: version 2.97 booting
[    2.870300] random: fast init done
Starting udev
[    3.218883] udevd[134]: starting version 3.2.9
[    3.226029] random: udevd: uninitialized urandom read (16 bytes read)
[    3.226973] random: udevd: uninitialized urandom read (16 bytes read)
[    3.227017] random: udevd: uninitialized urandom read (16 bytes read)
[    3.251773] udevd[135]: starting eudev-3.2.9
[    3.388533] pfeng: loading out-of-tree module taints kernel.
[    3.398585] pfeng 46000000.pfe: PFEng ethernet driver loading ...
[    3.398607] pfeng 46000000.pfe: Version: BETA 0.9.7
[    3.398612] pfeng 46000000.pfe: Multi instance support: disabled (standalone)
[    3.398617] pfeng 46000000.pfe: Compiled by: 10.2.0
[    3.398676] pfeng 46000000.pfe: Cbus addr 0x46000000 size 0x1000000
[    3.398687] pfeng 46000000.pfe: fsl,fw-class-name: s32g_pfe_class.fw
[    3.398694] pfeng 46000000.pfe: fsl,fw-util-name: s32g_pfe_util.fw
[    3.398772] pfeng 46000000.pfe: logif(pfe0) mode: std,tx-inject 
[    3.398790] pfeng 46000000.pfe: logif(pfe0) EMAC: 0
[    3.398804] pfeng 46000000.pfe: logif(pfe0) HIFs: count 1 map 01
[    3.398823] pfeng 46000000.pfe: logif(pfe1) mode: std,tx-inject 
[    3.398836] pfeng 46000000.pfe: logif(pfe1) EMAC: 1
[    3.398850] pfeng 46000000.pfe: logif(pfe1) HIFs: count 1 map 02
[    3.398868] pfeng 46000000.pfe: logif(pfe2) mode: std,tx-class
[    3.398881] pfeng 46000000.pfe: logif(pfe2) EMAC: 2
[    3.398893] pfeng 46000000.pfe: logif(pfe2) HIFs: count 1 map 04
[    3.399416] pfeng 46000000.pfe: HIF channels mask: 0x0007
[    3.399441] pfeng 46000000.pfe: PFE port coherency enabled, mask 0x1e
[    3.399649] pfeng 46000000.pfe: Clocks: sys=300MHz pe=600MHz
[    3.399669] pfeng 46000000.pfe: Interface selected: EMAC0: 0x4 EMAC1: 0x4 EMAC2: 0x9
[    3.400360] pfeng 46000000.pfe: PFE controller reset done
[    3.400450] pfeng 46000000.pfe: Failed to enable TX clocks on EMAC0 for interface sgmii. Error -5
[    3.400524] pfeng 46000000.pfe: Failed to enable RX clocks on EMAC0 for interface sgmii. Error -5
[    3.400593] pfeng 46000000.pfe: Failed to enable TX clocks on EMAC1 for interface sgmii. Error -5
[    3.400659] pfeng 46000000.pfe: Failed to enable RX clocks on EMAC1 for interface sgmii. Error -5
[    3.400717] pfeng 46000000.pfe: TX clock on EMAC2 for interface rgmii-id installed
[    3.400742] pfeng 46000000.pfe: RX clock on EMAC2 for interface rgmii-id installed
[    3.400837] pfeng 46000000.pfe: assigned reserved memory node pfebufs@83200000
[    3.418504] pfeng 46000000.pfe: Firmware: CLASS s32g_pfe_class.fw [165716 bytes]
[    3.418532] pfeng 46000000.pfe: Firmware: UTIL s32g_pfe_util.fw [136584 bytes]
[    3.418566] pfeng 46000000.pfe: PFE CBUS p0x46000000 mapped @ v0xffffffc015000000
[    3.418577] pfeng 46000000.pfe: Silicon S32G2
[    3.419703] pfeng 46000000.pfe: BMU1 buffer base: p0xc0000000
[    3.419807] pfeng 46000000.pfe: BMU2 buffer base: p0x83000000 (0x200000 bytes)
[    3.421129] pfeng 46000000.pfe: register IRQ 74 by name 'PFE BMU IRQ'
[    3.421384] pfeng 46000000.pfe: Firmware .elf detected
[    3.421391] pfeng 46000000.pfe: ELF_Open: File format: Elf32
[    3.421389] pfeng 46000000.pfe: BMU_EMPTY_INT (BMU @ p0x(____ptrval____)). Pool ready.
[    3.421398] pfeng 46000000.pfe: ELF_Open: File endian: Alien (Big)
[    3.421405] pfeng 46000000.pfe: BMU_EMPTY_INT (BMU @ p0x(____ptrval____)). Pool ready.
[    3.421410] pfeng 46000000.pfe: Uploading CLASS firmware
[    3.421420] pfeng 46000000.pfe: Selected FW loading OPs to load 8 PEs in parallel
[    3.441154] pfeng 46000000.pfe: pfe_ct.h file version"881ee579670388f6832743c0c1b2aac4"
[    3.456439] pfeng 46000000.pfe: [FW VERSION] 1.2.0, Build: Mar  9 2022, 09:23:00 (), ID: 0x31454650
[    3.456828] pfeng 46000000.pfe: The PHY mode selection is done using a HW interface. See the 'phy_intf_sel' signal.
[    3.456847] pfeng 46000000.pfe: The PHY mode selection is done using a HW interface. See the 'phy_intf_sel' signal.
[    3.456860] pfeng 46000000.pfe: The PHY mode selection is done using a HW interface. See the 'phy_intf_sel' signal.
[    3.456871] pfeng 46000000.pfe: SAFETY instance created
[    3.456882] pfeng 46000000.pfe: Watchdog instance created
[    3.456893] pfeng 46000000.pfe: ELF_Open: File format: Elf32
[    3.456900] pfeng 46000000.pfe: ELF_Open: File endian: Alien (Big)
[    3.456908] pfeng 46000000.pfe: Uploading UTIL firmware
[    3.456914] pfeng 46000000.pfe: Selected FW loading OPs to load 1 PEs in parallel
[    3.459393] pfeng 46000000.pfe: pfe_ct.h file version"881ee579670388f6832743c0c1b2aac4"
[    3.459774] pfeng 46000000.pfe: Using GPI ASEQ LEN 0x50
[    3.462189] pfeng 46000000.pfe: VLAN ID incorrect or not set. Using default VLAN ID = 0x01.
[    3.462196] pfeng 46000000.pfe: VLAN stats size incorrect or not set. Using default VLAN stats size = 20.
[    3.462274] pfeng 46000000.pfe: Fall-back bridge domain @ 0x20000a24 (class)
[    3.462281] pfeng 46000000.pfe: Default bridge domain @ 0x20000a1c (class)
[    3.462677] pfeng 46000000.pfe: Routing table created, Hash Table @ p0x83200000, Pool @ p0x83208000 (65536 bytes)
[    3.462936] pfeng 46000000.pfe: Feature err051211_workaround: DISABLED
[    3.464447] pfeng 46000000.pfe: MDIO bus 0 disabled in DT
[    3.464462] pfeng 46000000.pfe: MDIO bus 1 disabled in DT
[    3.464951] libphy: PFEng Ethernet MDIO: probed
[    3.485668] pfeng 46000000.pfe: HIF0 enabled
[    3.485941] pfeng 46000000.pfe: HIF1 enabled
[    3.486224] pfeng 46000000.pfe: HIF2 enabled
[    3.486231] pfeng 46000000.pfe: HIF3 not configured, skipped
[    3.487117] pfeng 46000000.pfe pfe0: registered
[    3.487157] pfeng 46000000.pfe pfe0: Subscribe to HIF0
[    3.487614] pfeng 46000000.pfe pfe0: Enable HIF0
[    3.487779] pfeng 46000000.pfe pfe0: setting MAC addr: 00:01:be:be:ef:11
[    3.487810] pfeng 46000000.pfe pfe0: PTP HW addend 0x80000000, max_adj configured to 46566128 ppb
[    3.487821] pfeng 46000000.pfe: IEEE1588: Input Clock: 200000000Hz, Output: 100000000Hz, Accuracy: 10.0ns
[    3.488360] pfeng 46000000.pfe pfe0: Registered PTP HW clock successfully on EMAC0
[    3.489055] pfeng 46000000.pfe pfe1: registered
[    3.489065] pfeng 46000000.pfe pfe1: Subscribe to HIF1
[    3.489483] pfeng 46000000.pfe pfe1: Enable HIF1
[    3.489648] pfeng 46000000.pfe pfe1: setting MAC addr: 00:01:be:be:ef:22
[    3.489680] pfeng 46000000.pfe pfe1: PTP HW addend 0x80000000, max_adj configured to 46566128 ppb
[    3.489690] pfeng 46000000.pfe: IEEE1588: Input Clock: 200000000Hz, Output: 100000000Hz, Accuracy: 10.0ns
[    3.490196] pfeng 46000000.pfe pfe1: Registered PTP HW clock successfully on EMAC1
[    3.490897] pfeng 46000000.pfe pfe2: registered
[    3.490906] pfeng 46000000.pfe pfe2: Subscribe to HIF2
[    3.491379] pfeng 46000000.pfe pfe2: Enable HIF2
[    3.491632] pfeng 46000000.pfe pfe2: setting MAC addr: 00:01:be:be:ef:33
[    3.491658] pfeng 46000000.pfe pfe2: PTP HW addend 0x80000000, max_adj configured to 46566128 ppb
[    3.491669] pfeng 46000000.pfe: IEEE1588: Input Clock: 200000000Hz, Output: 100000000Hz, Accuracy: 10.0ns
[    3.492143] pfeng 46000000.pfe pfe2: Registered PTP HW clock successfully on EMAC2
[    3.605853] sja1110 spi5.0: probing uc
[    3.606032] sja1110 spi5.1: probing switch
[    3.606385] sja1110 spi5.1: Could not get GPIO from device tree
[    3.606403] sja1110 spi5.1: [sja1110_post_probe_upload_worker] Trying to initialize switch
[    3.606484] sja1110 spi5.1: Direct firmware load for sja1110_switch.bin failed with error -2
[    3.606496] sja1110 spi5.1: request_firmware failed with -2
[    3.606504] sja1110 spi5.0: [sja1110_post_probe_upload_worker] Trying to initialize uC
[    3.606542] sja1110 spi5.0: Direct firmware load for sja1110_uc.bin failed with error -2
[    3.606550] sja1110 spi5.0: request_firmware failed with -2
[    3.628108] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[    4.184764] pfeng 46000000.pfe: HIF0 started
[    4.184796] pfeng 46000000.pfe pfe0: configuring for fixed/sgmii link mode
[    4.185103] pfeng 46000000.pfe pfe0: Link is Up - 1Gbps/Full - flow control off
[    4.229894] urandom_read: 5 callbacks suppressed
[    4.229918] random: dhcpcd: uninitialized urandom read (112 bytes read)
[    4.294342] pfeng 46000000.pfe: HIF1 started
[    6.311592] Aquantia AQR113c stmmac-0:08: aqr107_wait_reset_complete failed: -110
[    6.313147] pfeng 46000000.pfe pfe1: PHY [stmmac-0:08] driver [Aquantia AQR113c] (irq=POLL)
[    6.313161] pfeng 46000000.pfe pfe1: configuring for phy/sgmii link mode
[    6.313191] phy-s32gen1-serdes 44180000.serdes: Speed not supported
[    6.314224] IPv6: ADDRCONF(NETDEV_CHANGE): pfe0: link becomes ready
[    6.332085] random: dhcpcd: uninitialized urandom read (112 bytes read)
[    6.394952] pfeng 46000000.pfe: HIF2 started
[    6.459275] pfeng 46000000.pfe pfe2: PHY [PFEng Ethernet MDIO.2:04] driver [Micrel KSZ9031 Gigabit PHY] (irq=POLL)
[    6.459304] pfeng 46000000.pfe pfe2: configuring for phy/rgmii-id link mode
[    6.617955] s32cc-dwmac 4033c000.ethernet eth0: PHY [stmmac-0:01] driver [Micrel KSZ9031 Gigabit PHY] (irq=POLL)
[    6.627266] s32cc-dwmac 4033c000.ethernet eth0: Enabling Safety Features
[    6.627386] s32cc-dwmac 4033c000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[    6.627682] s32cc-dwmac 4033c000.ethernet eth0: registered PTP clock
[    6.629341] s32cc-dwmac 4033c000.ethernet eth0: configuring for phy/rgmii-id link mode
[    6.632048] 8021q: adding VLAN 0 to HW filter on device eth0
[    7.156998] random: crng init done
[    7.547854] pfeng 46000000.pfe: WDT_EMAC0_GPI_WDT_INT

Auto Linux BSP 32.0 s32g274ardb2 ttyLF0

s32g274ardb2 login: root
root@s32g274ardb2:~#