GPIO_PinRemapConfig(GPIO_Remap_I2C1,ENABLE); 复用重映射应用，默认复用和重映射复用区别

重映射就是将引脚功能重新定义到其他引脚，例如PA9是USART1-TX默认的管脚，但是现在PA9用做它用了，那可以将USART1-TX重新映射到PB6，当然这种映射不是随意的想映射到哪个脚就哪个脚，芯片内部已经固定了只能映射到固定的地方。

#ifndef _I2C_H_

#define _I2C_H_  

#include "STM32DEF.h"

#define I2C1_IsValid 1

#if I2C1_IsValid  

#define I2C_Speed 400000  

#define I2C1_GPIOxRemapEN 1//非0使能映射

extern void I2C1_AllInit(void);  

extern void I2C1_WaitDevieceStandbyState(uint8_t Addr);

#endif

#endif

 

 

#include "I2C1.h"

#if I2C1_IsValid

#include "stdio.h"  

static void I2C1_GPIOxConfig(void);

static void I2C1_HardwareConfig(void);

void I2C1_AllInit(void) {

RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C1,ENABLE);

#if I2C1_GPIOxRemapEN

GPIO_PinRemapConfig(GPIO_Remap_I2C1,ENABLE);

#endif

I2C1_GPIOxConfig();

I2C1_HardwareConfig();

}  

void I2C_Main(void) { }  /* Private functions ---------------------------------------------------------*/

 /*******************************************************************************  *

Function Name : GPIO_Configuration  * Description : Configure the used I/O ports pin * Input : None * Output : None * Return : None  

*******************************************************************************/  

static void I2C1_GPIOxConfig(void) {  

GPIO_InitTypeDef GPIO_InitStructure;  

#if I2C1_GPIOxRemapEN == 0   

RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB,ENABLE);

/* Configure I2C1 pins: SCL and SDA */  

GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6 | GPIO_Pin_7;

GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_OD;

GPIO_Init(GPIOB, &GPIO_InitStructure);

#else

GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8 | GPIO_Pin_9;

GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_OD;

GPIO_Init(GPIOB, &GPIO_InitStructure);

#endif }

 

 /*******************************************************************************  *

Function Name : I2C_HardwareConfig * Description : I2C I2C_HardwareConfig * Input : None * Output : None * Return : None  *******************************************************************************/  

static void I2C1_HardwareConfig(void) {  

I2C_InitTypeDef I2C_InitStructure;   /* I2C configuration */  

I2C_InitStructure.I2C_Mode = I2C_Mode_I2C;  

I2C_InitStructure.I2C_DutyCycle = I2C_DutyCycle_2;

I2C_InitStructure.I2C_OwnAddress1 = 0;

I2C_InitStructure.I2C_Ack = I2C_Ack_Enable;  

I2C_InitStructure.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit;

I2C_InitStructure.I2C_ClockSpeed = I2C_Speed;   /* Apply I2C configuration after enabling it */

I2C_Init(I2C1, &I2C_InitStructure);   /* I2C Peripheral Enable */

I2C_Cmd(I2C1, ENABLE); //I2C_AcknowledgeConfig(I2C1, ENABLE);

printf("\n\r I2C_Configuration----\n\r"); }  

/*******************************************************************************  *

Function Name : I2C_EE_WaitEepromStandbyState * Description : Wait for EEPROM Standby state * Input : None * Output : None * Return : None

*******************************************************************************/  

void I2C1_WaitDevieceStandbyState(uint8_t Addr) {  

vu16 SR1_Tmp = 0; do {   /* Send START condition */  

I2C_GenerateSTART(I2C1, ENABLE); /* Read I2C1 SR1 register */  

SR1_Tmp = I2C_ReadRegister(I2C1, I2C_Register_SR1); /* Send EEPROM address for write */  

I2C_Send7bitAddress(I2C1, Addr, I2C_Direction_Transmitter);

}while(!(I2C_ReadRegister(I2C1, I2C_Register_SR1) & 0x0002)); /* Clear AF flag */  

I2C_ClearFlag(I2C1, I2C_FLAG_AF); /* STOP condition */  

I2C_GenerateSTOP(I2C1, ENABLE); // Added by Najoua 27/08/2008 }  

#endif