STM32F103ZET定时器TIM1输出六路带死区互补PWM波形

使用默认引脚输出6路PWM，#define FullRemap_TIM1则重映射 PIN脚；

遗留问题：调用TIM_CCxNCmd(TIM1, TIM_Channel_X, TIM_CCx_Enable);导致互补PWM无输出。

TIM_CCxCmd(TIM1, TIM_Channel_X, TIM_CCx);确可以正常开关PWM输出；

遇到问题：PA8、10、PB13、14、15均有输出，PA9无输出；

问题解决：虽然没初始化UART1模块，但打开RCC_APB2Periph_USART1时钟导致；

void Timer1_Init(void)
{ 
    TIM_OCInitTypeDef TIM_OCInitStructure; 
    GPIO_InitTypeDef GPIO_InitStructure; 
    TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure; 
    TIM_BDTRInitTypeDef TIM_BDTRInitStructure; 
     
	NVIC_InitTypeDef NVIC_InitStructure;
     
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM1, ENABLE); 

#ifdef FullRemap_TIM1
    GPIO_PinRemapConfig(GPIO_FullRemap_TIM1, ENABLE); 
#endif
	
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8|GPIO_Pin_9|GPIO_Pin_10; 
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP; 
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; 
    GPIO_Init(GPIOA, &GPIO_InitStructure); 
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_13|GPIO_Pin_14|GPIO_Pin_15; 
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP; 
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; 
    GPIO_Init(GPIOB, &GPIO_InitStructure); 
#ifdef FullRemap_TIM1
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7|GPIO_Pin_8|GPIO_Pin_9
    |GPIO_Pin_10|GPIO_Pin_11|GPIO_Pin_12|GPIO_Pin_13|GPIO_Pin_14; 
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP; 
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; 
    GPIO_Init(GPIOE, &GPIO_InitStructure); 
#endif
    TIM_TimeBaseStructure.TIM_Period    = 5999;//ARR 10K 
    TIM_TimeBaseStructure.TIM_CounterMode       = TIM_CounterMode_Up; 
    TIM_TimeBaseStructure.TIM_Prescaler = 99;//??????1us 
    TIM_TimeBaseStructure.TIM_ClockDivision     = TIM_CKD_DIV1; 
    TIM_TimeBaseStructure.TIM_RepetitionCounter = 0x0000; 
    TIM_TimeBaseInit(TIM1, &TIM_TimeBaseStructure); 
     
    TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1; 
    TIM_OCInitStructure.TIM_OutputState  = TIM_OutputState_Enable; 
    TIM_OCInitStructure.TIM_OutputNState = TIM_OutputNState_Enable; 
    TIM_OCInitStructure.TIM_Pulse = 1000;//CCR 
    TIM_OCInitStructure.TIM_OCPolarity   = TIM_OCPolarity_Low; 
    TIM_OCInitStructure.TIM_OCNPolarity  = TIM_OCNPolarity_Low; //关断后PWM默认输出状态
    TIM_OCInitStructure.TIM_OCIdleState  = TIM_OCIdleState_Reset; 
    TIM_OCInitStructure.TIM_OCNIdleState = TIM_OCIdleState_Reset; 
    TIM_OC1Init(TIM1, &TIM_OCInitStructure); 
 
 	TIM_OCInitStructure.TIM_Pulse = 2000;//CCR 
 	TIM_OC2Init(TIM1, &TIM_OCInitStructure); 
 
    TIM_OCInitStructure.TIM_Pulse = 3000;//CCR 
 	TIM_OC3Init(TIM1, &TIM_OCInitStructure); 

    TIM_OC1PreloadConfig(TIM1, TIM_OCPreload_Enable); 
	TIM_OC2PreloadConfig(TIM1, TIM_OCPreload_Enable); 
	TIM_OC3PreloadConfig(TIM1, TIM_OCPreload_Enable); 
 
    TIM_BDTRInitStructure.TIM_OSSRState = TIM_OSSRState_Enable; 
    TIM_BDTRInitStructure.TIM_OSSIState = TIM_OSSIState_Enable; 
    TIM_BDTRInitStructure.TIM_LOCKLevel = TIM_LOCKLevel_OFF; 
    TIM_BDTRInitStructure.TIM_DeadTime = 0;
    TIM_BDTRInitStructure.TIM_Break = TIM_Break_Disable; 
    TIM_BDTRInitStructure.TIM_BreakPolarity = TIM_BreakPolarity_High; 
    TIM_BDTRInitStructure.TIM_AutomaticOutput = TIM_AutomaticOutput_Disable; 
	TIM_BDTRConfig(TIM1, &TIM_BDTRInitStructure); 

	NVIC_InitStructure.NVIC_IRQChannel = TIM1_UP_IRQn;
	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 2;  
	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; 
	NVIC_Init(&NVIC_InitStructure); 

    TIM_ITConfig(TIM1,TIM_IT_Update, ENABLE);
    TIM_ARRPreloadConfig(TIM1, ENABLE); 
    TIM_ClearITPendingBit(TIM1, TIM_IT_Update);
	TIM_CtrlPWMOutputs(TIM1, ENABLE); 
    TIM_Cmd(TIM1, ENABLE); 

	//TIM_CCxCmd(TIM1, TIM_Channel_1, TIM_CCx_Enable);
	//TIM_CCxNCmd(TIM1, TIM_Channel_1, TIM_CCx_Enable);
	//TIM_CCxCmd(TIM1, TIM_Channel_2, TIM_CCx_Enable);
	//TIM_CCxNCmd(TIM1, TIM_Channel_2, TIM_CCx_Enable);
	//TIM_CCxCmd(TIM1, TIM_Channel_3, TIM_CCx_Enable);
	//TIM_CCxNCmd(TIM1, TIM_Channel_3, TIM_CCx_Enable);
}

void TIM1_UP_IRQHandler(void)							//
{	
	if(TIM_GetITStatus(TIM1,TIM_IT_Update)!=RESET)
	{
		TIM_ClearITPendingBit(TIM1,TIM_IT_Update);
	}
}

声明：仅供本人备忘，其他用途后果自负；