交换机基本状态:
1 2 3 4 5 | switch: hostname> ;用户模式 hostname# ;特权模式(enable) hostname(config)# ;全局配置模式(interface g0/0||s0/0) hostname(config-if)# ;接口状态 |
交换机口令设置:
1 3 4 5 6 7 8 9 10 | switch>enable ;进入特权模式 switch#config terminal ;进入全局配置模式 switch(config)#hostname ;设置交换机的主机名 switch(config)#enable secret xxx ;设置特权加密口令 switch(config)#enable password xxa ;设置特权非密口令 switch(config)#line console 0 ;进入控制台口 switch(config-line)#line vty 0 4 ;进入虚拟终端 switch(config-line)#login ;允许登录 switch(config-line)#password xx ;设置登录口令xx switch#exit ;返回命令 |
交换机VLAN设置:
1 5 6 7 8 9 10 11 12 | switch#vlan database ;进入VLAN设置 switch(vlan)#vlan 2 ;建VLAN 2 switch(vlan)#no vlan 2 ;删vlan 2 switch(config)#int f0/1 ;进入端口1 switch(config-if)#switchport access vlan 2 ;当前端口加入vlan 2 switch(config-if)#switchport mode trunk ;设置为干线 switch(config-if)#switchport trunk allowed vlan 1,2 ;设置允许的vlan switch(config-if)#switchport trunk encap dot1q ;设置vlan 中继 switch(config)#vtp domain ;设置发vtp域名 switch(config)#vtp password ;设置发vtp密码 switch(config)#vtp mode server ;设置发vtp模式 switch(config)#vtp mode client ;设置发vtp模式 |
交换机设置IP地址:
1 2 | switch(config)#interface vlan 1 ;进入vlan 1 switch(config-if)#ip address ;设置IP地址 switch(config)#ip default-gateway ;设置默认网关 |
交换机显示命令:
1 2 3 4 5 | switch#write ;保存配置信息 switch#show run ;查看当前配置信息 switch#show vlan ;查看vlan配置信息 switch#show interface ;查看端口信息 switch#show int f0/0 ;查看指定端口信息 |
2. 路由器支持的命令:
路由器显示命令:
1 2 3 | router#show run ;显示配置信息 router#show interface ;显示接口信息 router#show ip route ;显示路由信息 |
路由器口令设置:
1 4 5 6 7 8 9 10 11 | router>enable ;进入特权模式 router#config terminal ;进入全局配置模式 router(config)#hostname ;设置交换机的主机名 router(config)#enable secret xxx ;设置特权加密口令 router(config)#enable password xxb ;设置特权非密口令 router(config)#line console 0 ;进入控制台口 router(config-line)#line vty 0 4 ;进入虚拟终端 router(config-line)#login ;要求口令验证 router(config-line)#password xx ;设置登录口令xx router(config)#(Ctrl+z) ; 返回特权模式 router#exit ;返回命令 |
路由器配置:
2 3 4 5 6 7 8 9 10 | router(config)#int s0/0 ;进入Serail接口 router(config-if)#no shutdown ;激活当前接口 router(config-if)#clock rate 64000 ;设置同步时钟 router(config-if)#ip address ;设置IP地址 router(config-if)#ip address second ;设置第二个IP router(config-if)#int f0/0.1 ;进入子接口 router(config-subif.1)#ip address ;设置子接口IP router(config-subif.1)#encapsulation dot1q ;绑定vlan中继协议 router(config)#config-register 0x2142 ;跳过配置文件 router(config)#config-register 0x2102 ;正常使用配置文件 router#reload ;重新引导 |
静态路由:
1 2 3 | ip route ;命令格式 router(config)#ip route 2.0.0.0 255.0.0.0 1.1.1.2 ;静态路由举例 router(config)#ip route 0.0.0.0 0.0.0.0 1.1.1.2 ;默认路由举例 |
动态路由:
1 2 3 4 | router(config)#ip route ;启动路由转发 router(config)#router rip ;启动RIP路由协议。 router(config-router)#network 目标网络布路由 router(config-router)#version 2 (no auto-summary) |