rip......

已于 2022-11-22 18:27:18 修改
阅读量75 收藏
点赞数
文章标签： 网络
于 2022-11-22 17:07:03 首次发布
版权声明：本文为博主原创文章，遵循 CC 4.0 BY-SA 版权协议，转载请附上原文出处链接和本声明。
本文链接：https://blog.csdn.net/m0_74812057/article/details/127986281
版权

[Huawei]sysname r1
[r1]user-int    
[r1]user-interface con    
[r1]user-interface console 0
[r1-ui-console0]idle    
[r1-ui-console0]idle-timeout 0 0
[r1-ui-console0]quit
[r1]int g0/0/0
[r1-GigabitEthernet0/0/0]ip add    
[r1-GigabitEthernet0/0/0]ip address 12.1.1.1 24
Nov 20 2022 22:31:06-08:00 r1 %%01IFNET/4/LINK_STATE(l)[1]:The line protocol IP
on the interface GigabitEthernet0/0/0 has entered the UP state.
[r1-GigabitEthernet0/0/0]quit
[r1]int    
[r1]interface Loop    
[r1]interface LoopBack 0
[r1-LoopBack0]ip add    
[r1-LoopBack0]ip address 1.1.1.1 32
[r1-LoopBack0]quit
[r1]rip 1
[r1-rip-1]ver    
[r1-rip-1]verify-source
[r1-rip-1]version 2
[r1-rip-1]net    
[r1-rip-1]network 12.0.0.0
[r1-rip-1]def    
[r1-rip-1]default-rou    
[r1-rip-1]default-route ori    
[r1-rip-1]default-route originate
[r1-rip-1]quit
[r1]int g0/0/0
[r1-GigabitEthernet0/0/0]rip au    
[r1-GigabitEthernet0/0/0]rip authentication-mode sim    
[r1-GigabitEthernet0/0/0]rip authentication-mode simple cip    
[r1-GigabitEthernet0/0/0]rip authentication-mode simple cipher 123
[r1-GigabitEthernet0/0/0]quit
[r1]rip 1
[r1-rip-1]tim    
[r1-rip-1]timers rip 15 90 90
[r1-rip-1]quit
[r1]pimg 192.168.1.1
    ^
Error: Unrecognized command found at '^' position.
[r1]pimg 192.168.1.1
    ^
Error: Unrecognized command found at '^' position.
[r1]ping 192.168.1.1
  PING 192.168.1.1: 56  data bytes, press CTRL_C to break
    Request time out
    Reply from 192.168.1.1: bytes=56 Sequence=2 ttl=254 time=30 ms
    Reply from 192.168.1.1: bytes=56 Sequence=3 ttl=254 time=20 ms
    Reply from 192.168.1.1: bytes=56 Sequence=4 ttl=254 time=30 ms
    Reply from 192.168.1.1: bytes=56 Sequence=5 ttl=254 time=30 ms

  --- 192.168.1.1 ping statistics ---
    5 packet(s) transmitted
    4 packet(s) received
    20.00% packet loss
    round-trip min/avg/max = 20/27/30 ms

[r1]ping 192.168.2.1
  PING 192.168.2.1: 56  data bytes, press CTRL_C to break
    Reply from 192.168.2.1: bytes=56 Sequence=1 ttl=254 time=40 ms
    Reply from 192.168.2.1: bytes=56 Sequence=2 ttl=254 time=40 ms
    Reply from 192.168.2.1: bytes=56 Sequence=3 ttl=254 time=20 ms
    Reply from 192.168.2.1: bytes=56 Sequence=4 ttl=254 time=30 ms
    Reply from 192.168.2.1: bytes=56 Sequence=5 ttl=254 time=20 ms

  --- 192.168.2.1 ping statistics ---
    5 packet(s) transmitted
    5 packet(s) received
    0.00% packet loss
    round-trip min/avg/max = 20/30/40 ms

r2
<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname r2
[r2]user-int    
[r2]user-interface con    
[r2]user-interface console 0
[r2-ui-console0]idle    
[r2-ui-console0]idle-timeout 0 0
[r2-ui-console0]quit
[r2]int g0/0/0
[r2-GigabitEthernet0/0/0]ip add    
[r2-GigabitEthernet0/0/0]ip address 12.1.1.2 24
Nov 20 2022 22:33:53-08:00 r2 %%01IFNET/4/LINK_STATE(l)[2]:The line protocol IP
on the interface GigabitEthernet0/0/0 has entered the UP state.
[r2-GigabitEthernet0/0/0]int g0/0/1
[r2-GigabitEthernet0/0/1]ip add    
[r2-GigabitEthernet0/0/1]ip address 23.1.1.1 24
Nov 20 2022 22:34:12-08:00 r2 %%01IFNET/4/LINK_STATE(l)[3]:The line protocol IP
on the interface GigabitEthernet0/0/1 has entered the UP state.
[r2-GigabitEthernet0/0/1]quit
[r2]int LOOp    
[r2]int
        ^
Error:Incomplete command found at '^' position.
[r2]int    
[r2]interface Loop
                   ^
Error:Incomplete command found at '^' position.
[r2]interface Loop    
[r2]interface LoopBack 0
[r2-LoopBack0]ip add    
[r2-LoopBack0]ip address 2.2.2.2 32
[r2-LoopBack0]quit
[r2]rip
[r2-rip-1]ver    
[r2-rip-1]verify-source
[r2-rip-1]version 2
[r2-rip-1]net    
[r2-rip-1]network 12.0.0.0
[r2-rip-1]net    
[r2-rip-1]network 23.0.0.0
[r2-rip-1]net    
[r2-rip-1]network 2.0.0.0
[r2-rip-1]quit
[r2]rip au    
[r2]int g0/0/0
[r2-GigabitEthernet0/0/0]rip au    
[r2-GigabitEthernet0/0/0]rip authentication-mode sim    
[r2-GigabitEthernet0/0/0]rip authentication-mode simple cip    
[r2-GigabitEthernet0/0/0]rip authentication-mode simple cipher 123
[r2-GigabitEthernet0/0/0]int g0/0/1
[r2-GigabitEthernet0/0/1]rip au    
[r2-GigabitEthernet0/0/1]rip authentication-mode md5 us    
[r2-GigabitEthernet0/0/1]rip authentication-mode md5 usual cip    
[r2-GigabitEthernet0/0/1]rip authentication-mode md5 usual cipher 123
[r2-GigabitEthernet0/0/1]quit
[r2]rip 1
[r2-rip-1]timers rip 15 90 90

r3
<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]sys    
[Huawei]sysname r3
[r3]user-int    
[r3]user-interface con    
[r3]user-interface console 0
[r3-ui-console0]idle    
[r3-ui-console0]idle-timeout 0 0
[r3-ui-console0]quit
[r3]int g0/0/0
[r3-GigabitEthernet0/0/0]ip add    
[r3-GigabitEthernet0/0/0]ip address 23.1.1.2 24
Nov 20 2022 22:36:34-08:00 r3 %%01IFNET/4/LINK_STATE(l)[2]:The line protocol IP
on the interface GigabitEthernet0/0/0 has entered the UP state.
[r3-GigabitEthernet0/0/0]int g0/0/1
[r3-GigabitEthernet0/0/1]ip add    
[r3-GigabitEthernet0/0/1]ip address 34.1.1.1 24
Nov 20 2022 22:36:56-08:00 r3 %%01IFNET/4/LINK_STATE(l)[3]:The line protocol IP
on the interface GigabitEthernet0/0/1 has entered the UP state.
[r3-GigabitEthernet0/0/1]quit
[r3]int    
[r3]interface Loop
                   ^
Error:Incomplete command found at '^' position.
[r3]interface Loop    
[r3]interface LoopBack 0
[r3-LoopBack0]ip add    
[r3-LoopBack0]ip address 192.168.1.1 24
[r3-LoopBack0]quit
[r3]int    
[r3]interface Loop    
[r3]interface LoopBack 1
[r3-LoopBack1]ip add    
[r3-LoopBack1]ip address 192.168.2.1 24
[r3-LoopBack1]quit
[r3]rip 1
[r3-rip-1]ver    
[r3-rip-1]verify-source`    
[r3-rip-1]verify-source    
[r3-rip-1]ver    
[r3-rip-1]version 2
[r3-rip-1]net    
[r3-rip-1]network 23.0.0.0
[r3-rip-1]net    
[r3-rip-1]network 34.0.0.0
[r3-rip-1]net    
[r3-rip-1]network 192.168.1.0
[r3-rip-1]net    
[r3-rip-1]network 192.168.2.0
[r3-rip-1]quit
[r3]int g0/0/0
[r3-GigabitEthernet0/0/0]rip au    
[r3-GigabitEthernet0/0/0]rip authentication-mode md5 us    
[r3-GigabitEthernet0/0/0]rip authentication-mode md5 usual cip    
[r3-GigabitEthernet0/0/0]rip authentication-mode md5 usual cipher 123
[r3-GigabitEthernet0/0/0]quit
[r3]rip 1
[r3-rip-1]timers rip 15 90 90
[r3-rip-1]quit
[r3]int g0/0/0
[r3-GigabitEthernet0/0/0]rip sum    
[r3-GigabitEthernet0/0/0]rip summary-address 192.168.0.0 255.255.252.0
[r3-GigabitEthernet0/0/0]int g0/0/1
[r3-GigabitEthernet0/0/1]rip sum    
[r3-GigabitEthernet0/0/1]rip summary-address 192.168.0.0 255.255.252.0
[r3-GigabitEthernet0/0/1]

r4
The device is running!
########
<Huawei>
Nov 20 2022 22:29:52-08:00 Huawei %%01IFPDT/4/IF_STATE(l)[0]:Interface GigabitEt
hernet0/0/0 has turned into UP state.
<Huawei>

  Please check whether system data has been changed, and save data in time

  Configuration console time out, please press any key to log on

<Huawei>sy
Enter system view, return user view with Ctrl+Z.
[Huawei]sys    
[Huawei]sysname r4
[r4]user-    
[r4]user-int    
[r4]user-interface con    
[r4]user-interface console 0
[r4-ui-console0]idle    
[r4-ui-console0]idle-timeout 0 0
[r4-ui-console0]quit
[r4]int g0/0/0
[r4-GigabitEthernet0/0/0]
[r4-GigabitEthernet0/0/0]ip add    
[r4-GigabitEthernet0/0/0]ip address 34.1.1.2 24
Nov 20 2022 22:39:34-08:00 r4 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP
on the interface GigabitEthernet0/0/0 has entered the UP state.
[r4-GigabitEthernet0/0/0]quit
[r4]int    
[r4]interface Loop    
[r4]interface LoopBack 0
[r4-LoopBack0]ip add    
[r4-LoopBack0]ip address 4.4.4.4 32
[r4-LoopBack0]quit
[r4]rip 1
[r4-rip-1]ver    
[r4-rip-1]verify-source
[r4-rip-1]version 2
[r4-rip-1]net    
[r4-rip-1]network 34.0.0.0
[r4-rip-1]net    
[r4-rip-1]network 4.0.0.0
[r4-rip-1]quit
[r4]dis    
[r4]display ip     
[r4]display ip rou    
[r4]display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
         Destinations : 13       Routes : 13       

Destination/Mask    Proto   Pre  Cost      Flags NextHop         Interface

        2.2.2.2/32  RIP     100  2           D   34.1.1.1        GigabitEthernet
0/0/0
        4.4.4.4/32  Direct  0    0           D   127.0.0.1       LoopBack0
       12.1.1.0/24  RIP     100  2           D   34.1.1.1        GigabitEthernet
0/0/0
       23.1.1.0/24  RIP     100  1           D   34.1.1.1        GigabitEthernet
0/0/0
       34.1.1.0/24  Direct  0    0           D   34.1.1.2        GigabitEthernet
0/0/0
       34.1.1.2/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/0
     34.1.1.255/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/0
      127.0.0.0/8   Direct  0    0           D   127.0.0.1       InLoopBack0
      127.0.0.1/32  Direct  0    0           D   127.0.0.1       InLoopBack0
127.255.255.255/32  Direct  0    0           D   127.0.0.1       InLoopBack0
    192.168.1.0/24  RIP     100  1           D   34.1.1.1        GigabitEthernet
0/0/0
    192.168.2.0/24  RIP     100  1           D   34.1.1.1        GigabitEthernet
0/0/0
255.255.255.255/32  Direct  0    0           D   127.0.0.1       InLoopBack0

[r4]dis    
[r4]display ip rou    
[r4]display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
         Destinations : 14       Routes : 14       

Destination/Mask    Proto   Pre  Cost      Flags NextHop         Interface

        0.0.0.0/0   RIP     100  3           D   34.1.1.1        GigabitEthernet
0/0/0
        2.2.2.2/32  RIP     100  2           D   34.1.1.1        GigabitEthernet
0/0/0
        4.4.4.4/32  Direct  0    0           D   127.0.0.1       LoopBack0
       12.1.1.0/24  RIP     100  2           D   34.1.1.1        GigabitEthernet
0/0/0
       23.1.1.0/24  RIP     100  1           D   34.1.1.1        GigabitEthernet
0/0/0
       34.1.1.0/24  Direct  0    0           D   34.1.1.2        GigabitEthernet
0/0/0
       34.1.1.2/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/0
     34.1.1.255/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/0
      127.0.0.0/8   Direct  0    0           D   127.0.0.1       InLoopBack0
      127.0.0.1/32  Direct  0    0           D   127.0.0.1       InLoopBack0
127.255.255.255/32  Direct  0    0           D   127.0.0.1       InLoopBack0
    192.168.1.0/24  RIP     100  1           D   34.1.1.1        GigabitEthernet
0/0/0
    192.168.2.0/24  RIP     100  1           D   34.1.1.1        GigabitEthernet
0/0/0
255.255.255.255/32  Direct  0    0           D   127.0.0.1       InLoopBack0

[r4]rip 1
[r4-rip-1]timers rip 15 90 90

m0_74812057
关注
hcip网络类型实验报告
gyuguyfdsd的博客
01-01 412
HCIP
静态路由练习
2201_75408313的博客
04-22 94
网络设备在启动之后，当设备的接口处于UP状态时，设备能够自己去发现去往与自己接口直连相 连的网络的路由。
2021-05-27
m0_56229717的博客
05-27 620
拓扑图 R1 Please press enter to start cmd line! <r1> May 26 2021 20:04:16-08:00 r1 %%01IFPDT/4/IF_STATE(l)[0]:Interface GigabitEthern et0/0/1 has turned into UP state. <r1> May 26 2021 20:04:20-08:00 r1 %%01IFPDT/4/IF_STATE(l)[1]:In...
路由练习作业
newqian的博客
01-04 688
练习作业
Assassins.Creed.III.TW.THETA.RIP.torrent
07-20
Assassins.Creed.III.TW.THETA.RIP.torrent3DMGAME.Assassins.Creed.III.TW.THETA.RIP.torrent3DMGAME.Assassins.Creed.III.TW.THETA.RIP.torrent3DMGAME.Assassins.Creed.III.TW.THETA.RIP.torrent3DMGAME....
4RIP .pka
04-03
4RIP 4RIP .pka
北航计网课实验4-实验报告-RIP.docx
12-18
"北航计网课实验4-实验报告-RIP.docx" 这篇实验报告主要讲述了RIP（Routing Information Protocol，路由信息协议）协议的实验，涉及到静态路由、缺省路由和RIP协议的配置、路由表的分析、RIP报文的解析等内容。 ...
VRRP&RIP.rar
最新发布
10-22
VRRP&RIP.rar
GB0-192-删除FR、RIP.doc
08-20
【GB0-192-删除FR、RIP】这篇文档可能是一份关于H3C GB0-192认证考试的学习资料，其中包含了多个IT网络领域的知识点，主要涉及OSI模型、网络设备、IP地址、TCP连接、FTP协议、操作系统启动、STP协议以及交换机配置等...
BGP综合实验
dongxuK的博客
05-12 614
配置vpn让r1和r8业务网段通。使用ospf将as内部搞通。
HCIA第五次实验
ElevenMaple的博客
11-22 137
hcia
2021-05-20
m0_56229717的博客
05-20 247
题目要求 截图 代码 [Huawei]sysname r1 [r1]inter [r1]interface G [r1]interface GigabitEthernet 0/0/1 [r1-GigabitEthernet0/0/1]IP ADD [r1-GigabitEthernet0/0/1]IP address 12.1.1.1 24 [r1-GigabitEthernet0/0/1] May 17 2021 18:38:54-08:00 r1 %%01IFNET/4/..
ip 复习第二天实验网络类型
m0_56229717的博客
07-08 522
部分代码 r1 0 packet(s) received 100.00% packet loss [r1-Serial4/0/0]ping 15.1.1.2 Jul 8 2021 17:56:27-08:00 r1 %%01IFNET/4/LINK_STATE(l)[13]:The line protocol PP P on the interface Serial4/0/0 has entered the UP state. [r1-Serial4/0/0]ping ...
OSPF实验
hdlaichi_的博客
03-21 487
The device is running!<Huawei> Please check whether system data has been changed, and save data in time Configuration console time out, please press any key to log on<Huawei> <Huawei> <Huawei>sys Enter system view, return user view with Ctrl+Z. [Huawei]s
华为--IA复习静态路由实验
weixin_43774199的博客
11-04 2037
1、实验拓扑 2、实验要求 全网可达 拓扑中所需地址全部基于192.168.0.0/24划分所得 静态路由（不许使用其他动态） R8环回需要汇总 3、实验分析及拓扑处理
OSPF 常见错误与排查方法
weixin_34349320的博客
12-10 1174
OSPF是一种配置上比较复杂的协议， 所以在实际操作中非常容易出错，这里介绍一下OSPF的一些常见错误和排查方法： 　　一、OSPF 邻居关系无法建立 　　这是实际工程中最为常见的错误，对于这种错误需要到以下命令进行排查： 　　首先需要使用的命令是Show ip ospf interface，这条命令输出信息中能够影响到OSPF邻居关系建立的有几个因素 ： 　　1、...
rip的使用
weixin_74812361的博客
11-18 263
1.使用ripv2全网可达2保证更新安全 12之间使用明文 23之间使用密文3.r3的环回做汇总192.168.1.0/24 192.168.2.0/24 4.r1的环回不能宣告全网可达。
从ip addr add和ifconfig的区别看linux网卡ip地址的结构
热门推荐
Netfilter
02-09 10万+
今天一个老外在邮件列表上问了一个问题，就是ip addr add和ifconfig的区别，我给他进行了解答，可能因为英语不好吧，解答的很简单，因此我还是要在这里详细说明一下。其实它们之间没有什么区别，只 是表述方式不同罢了。如果你非常理解网络协议的原理以及网络的分层架构那么我想你就不会有这个问题，实际上，每一个网卡设备都有一个mac地址，但是却可 以有多个网络层地址，比如IP地址，然而这个事实无法
fmt_ninjaripper_rip.py
09-25
fmt_ninjaripper_rip.py是一个用于使用NinjaRipper软件进行游戏资源提取的Python脚本。NinjaRipper是一种专门用于抓取游戏中的3D模型、纹理和其他资源的工具。该脚本可以帮助用户更简便地使用NinjaRipper进行提取。 ...
评论
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付：10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明：

1.余额是钱包充值的虚拟货币，按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载，可以购买VIP、付费专栏及课程。

余额充值