tiny4412 驱动 （3）网卡驱动移植

最新推荐文章于 2023-05-16 12:19:14 发布
最新推荐文章于 2023-05-16 12:19:14 发布
阅读量823 收藏 5
点赞数
分类专栏： tiny4412 tiny4412
版权声明：本文为博主原创文章，遵循 CC 4.0 BY-SA 版权协议，转载请附上原文出处链接和本声明。
本文链接：https://blog.csdn.net/qq_21353001/article/details/90738462
版权

网卡驱动是后面驱动的基础

 

型号 DM9621

USB_HOST_ETHNET_DP1+ USB4604

USB_HOST_ETHNET_DP1- USB4604

其中USB4604有四路USB

一路接网卡DM9621， 一路引出标号USBH3， 另外两路USBH1heUSBH2,都是usb-typeA

对于USB4604

复位信号 ： GPM2_4_USBRST ， 接B35

XuhostDATA1 B59

XuhostSTROBE1 B57

相关驱动

drivers/usb/misc/usb4604.c

enum usb4604_mode {
        USB4604_MODE_UNKNOWN,
        USB4604_MODE_HUB,
        USB4604_MODE_STANDBY,
};

#ifdef CONFIG_OF
static const struct of_device_id usb4604_of_match[] = {
        { .compatible = "smsc,usb4604" },
        {}
};
MODULE_DEVICE_TABLE(of, usb4604_of_match);
#endif

static struct i2c_driver usb4604_i2c_driver = {
        .driver = {
                .name = "usb4604",
                .pm = &usb4604_i2c_pm_ops,
                .of_match_table = of_match_ptr(usb4604_of_match),
        },
        .probe          = usb4604_i2c_probe,
        .id_table       = usb4604_id,
};
module_i2c_driver(usb4604_i2c_driver);

注意这里没有使用module_init等来加载驱动，而是使用module_i2c_driver， 说明还需要IIC

根据网上资料把相同目录的drivers/usb/misc/usb3503.c移植过来就可以了

此外还有include/linux/platform_data/usb3503.h

cp include/linux/platform_data/usb3503.h include/linux/platform_data/usb4604.h
cp drivers/usb/misc/usb3503.c drivers/usb/misc/usb4604.c

vim include/linux/platform_data/usb4604.h

/* SPDX-License-Identifier: GPL-2.0 */
#ifndef __USB4604_H__
#define __USB4604_H__

#define USB4604_I2C_NAME        "usb4604"

#define USB4604_OFF_PORT1       (1 << 1)
#define USB4604_OFF_PORT2       (1 << 2)
#define USB6604_OFF_PORT3       (1 << 3)

enum usb4604_mode {
        USB4604_MODE_UNKNOWN,
        USB4604_MODE_HUB,
        USB4604_MODE_STANDBY,
};

struct usb4604_platform_data {
        enum usb4604_mode       initial_mode;
        u8      port_off_mask;
        int     gpio_intn;
        int     gpio_connect;
        int     gpio_reset;
};

#endif

vim drivers/usb/misc/usb4604.c

// SPDX-License-Identifier: GPL-2.0+
/*
 * Driver for SMSC USB4604 USB 2.0 hub controller driver
 *
 * Copyright (c) 2012-2013 Dongjin Kim (tobetter@gmail.com)
 */

#include <linux/clk.h>
#include <linux/i2c.h>
#include <linux/gpio.h>
#include <linux/delay.h>
#include <linux/slab.h>
#include <linux/module.h>
#include <linux/of_gpio.h>
#include <linux/platform_device.h>
#include <linux/platform_data/usb4604.h>
#include <linux/regmap.h>

#define USB4604_VIDL		0x00
#define USB4604_VIDM		0x01
#define USB4604_PIDL		0x02
#define USB4604_PIDM		0x03
#define USB4604_DIDL		0x04
#define USB4604_DIDM		0x05

#define USB4604_CFG1		0x06
#define USB4604_SELF_BUS_PWR	(1 << 7)

#define USB4604_CFG2		0x07
#define USB4604_CFG3		0x08
#define USB4604_NRD		0x09

#define USB4604_PDS		0x0a

#define USB4604_SP_ILOCK	0xe7
#define USB4604_SPILOCK_CONNECT	(1 << 1)
#define USB4604_SPILOCK_CONFIG	(1 << 0)

#define USB4604_CFGP		0xee
#define USB4604_CLKSUSP		(1 << 7)

#define USB4604_RESET		0xff

struct usb4604 {
	enum usb4604_mode	mode;
	struct regmap		*regmap;
	struct device		*dev;
	struct clk		*clk;
	u8	port_off_mask;
	int	gpio_intn;
	int	gpio_reset;
	int	gpio_connect;
	bool	secondary_ref_clk;
};

static int usb4604_reset(struct usb4604 *hub, int state)
{
	if (!state && gpio_is_valid(hub->gpio_connect))
		gpio_set_value_cansleep(hub->gpio_connect, 0);

	if (gpio_is_valid(hub->gpio_reset))
		gpio_set_value_cansleep(hub->gpio_reset, state);

	/* Wait T_HUBINIT == 4ms for hub logic to stabilize */
	if (state)
		usleep_range(4000, 10000);

	return 0;
}

static int usb4604_connect(struct usb4604 *hub)
{
	struct device *dev = hub->dev;
	int err;

	usb4604_reset(hub, 1);

	if (hub->regmap) {
		/* SP_ILOCK: set connect_n, config_n for config */
		err = regmap_write(hub->regmap, USB4604_SP_ILOCK,
			   (USB4604_SPILOCK_CONNECT
				 | USB4604_SPILOCK_CONFIG));
		if (err < 0) {
			dev_err(dev, "SP_ILOCK failed (%d)\n", err);
			return err;
		}

		/* PDS : Set the ports which are disabled in self-powered mode. */
		if (hub->port_off_mask) {
			err = regmap_update_bits(hub->regmap, USB4604_PDS,
					hub->port_off_mask,
					hub->port_off_mask);
			if (err < 0) {
				dev_err(dev, "PDS failed (%d)\n", err);
				return err;
			}
		}

		/* CFG1 : Set SELF_BUS_PWR, this enables self-powered operation. */
		err = regmap_update_bits(hub->regmap, USB4604_CFG1,
					 USB4604_SELF_BUS_PWR,
					 USB4604_SELF_BUS_PWR);
		if (err < 0) {
			dev_err(dev, "CFG1 failed (%d)\n", err);
			return err;
		}

		/* SP_LOCK: clear connect_n, config_n for hub connect */
		err = regmap_update_bits(hub->regmap, USB4604_SP_ILOCK,
					 (USB4604_SPILOCK_CONNECT
					  | USB4604_SPILOCK_CONFIG), 0);
		if (err < 0) {
			dev_err(dev, "SP_ILOCK failed (%d)\n", err);
			return err;
		}
	}

	if (gpio_is_valid(hub->gpio_connect))
		gpio_set_value_cansleep(hub->gpio_connect, 1);

	hub->mode = USB4604_MODE_HUB;
	dev_info(dev, "switched to HUB mode\n");

	return 0;
}

static int usb4604_switch_mode(struct usb4604 *hub, enum usb4604_mode mode)
{
	struct device *dev = hub->dev;
	int err = 0;

	switch (mode) {
	case USB4604_MODE_HUB:
		err = usb4604_connect(hub);
		break;

	case USB4604_MODE_STANDBY:
		usb4604_reset(hub, 0);
		dev_info(dev, "switched to STANDBY mode\n");
		break;

	default:
		dev_err(dev, "unknown mode is requested\n");
		err = -EINVAL;
		break;
	}

	return err;
}

static const struct regmap_config usb4604_regmap_config = {
	.reg_bits = 8,
	.val_bits = 8,

	.max_register = USB4604_RESET,
};

static int usb4604_probe(struct usb4604 *hub)
{
	struct device *dev = hub->dev;
	struct usb4604_platform_data *pdata = dev_get_platdata(dev);
	struct device_node *np = dev->of_node;
	int err;
	u32 mode = USB4604_MODE_HUB;
	const u32 *property;
	int len;

	if (pdata) {
		hub->port_off_mask	= pdata->port_off_mask;
		hub->gpio_intn		= pdata->gpio_intn;
		hub->gpio_connect	= pdata->gpio_connect;
		hub->gpio_reset		= pdata->gpio_reset;
		hub->mode		= pdata->initial_mode;
	} else if (np) {
		struct clk *clk;
		u32 rate = 0;
		hub->port_off_mask = 0;

		if (!of_property_read_u32(np, "refclk-frequency", &rate)) {
			switch (rate) {
			case 38400000:
			case 26000000:
			case 19200000:
			case 12000000:
				hub->secondary_ref_clk = 0;
				break;
			case 24000000:
			case 27000000:
			case 25000000:
			case 50000000:
				hub->secondary_ref_clk = 1;
				break;
			default:
				dev_err(dev,
					"unsupported reference clock rate (%d)\n",
					(int) rate);
				return -EINVAL;
			}
		}

		clk = devm_clk_get(dev, "refclk");
		if (IS_ERR(clk) && PTR_ERR(clk) != -ENOENT) {
			dev_err(dev, "unable to request refclk (%ld)\n",
					PTR_ERR(clk));
			return PTR_ERR(clk);
		}

		if (!IS_ERR(clk)) {
			hub->clk = clk;

			if (rate != 0) {
				err = clk_set_rate(hub->clk, rate);
				if (err) {
					dev_err(dev,
						"unable to set reference clock rate to %d\n",
						(int) rate);
					return err;
				}
			}

			err = clk_prepare_enable(hub->clk);
			if (err) {
				dev_err(dev,
					"unable to enable reference clock\n");
				return err;
			}
		}

		property = of_get_property(np, "disabled-ports", &len);
		if (property && (len / sizeof(u32)) > 0) {
			int i;
			for (i = 0; i < len / sizeof(u32); i++) {
				u32 port = be32_to_cpu(property[i]);
				if ((1 <= port) && (port <= 3))
					hub->port_off_mask |= (1 << port);
			}
		}

		hub->gpio_intn	= of_get_named_gpio(np, "intn-gpios", 0);
		if (hub->gpio_intn == -EPROBE_DEFER)
			return -EPROBE_DEFER;
		hub->gpio_connect = of_get_named_gpio(np, "connect-gpios", 0);
		if (hub->gpio_connect == -EPROBE_DEFER)
			return -EPROBE_DEFER;
		hub->gpio_reset = of_get_named_gpio(np, "reset-gpios", 0);
		if (hub->gpio_reset == -EPROBE_DEFER)
			return -EPROBE_DEFER;
		of_property_read_u32(np, "initial-mode", &mode);
		hub->mode = mode;
	}

	if (hub->port_off_mask && !hub->regmap)
		dev_err(dev, "Ports disabled with no control interface\n");

	if (gpio_is_valid(hub->gpio_intn)) {
		int val = hub->secondary_ref_clk ? GPIOF_OUT_INIT_LOW :
						   GPIOF_OUT_INIT_HIGH;
		err = devm_gpio_request_one(dev, hub->gpio_intn, val,
					    "usb4604 intn");
		if (err) {
			dev_err(dev,
				"unable to request GPIO %d as interrupt pin (%d)\n",
				hub->gpio_intn, err);
			return err;
		}
	}

	if (gpio_is_valid(hub->gpio_connect)) {
		err = devm_gpio_request_one(dev, hub->gpio_connect,
				GPIOF_OUT_INIT_LOW, "usb4604 connect");
		if (err) {
			dev_err(dev,
				"unable to request GPIO %d as connect pin (%d)\n",
				hub->gpio_connect, err);
			return err;
		}
	}

	if (gpio_is_valid(hub->gpio_reset)) {
		err = devm_gpio_request_one(dev, hub->gpio_reset,
				GPIOF_OUT_INIT_LOW, "usb4604 reset");
		/* Datasheet defines a hardware reset to be at least 100us */
		usleep_range(100, 10000);
		if (err) {
			dev_err(dev,
				"unable to request GPIO %d as reset pin (%d)\n",
				hub->gpio_reset, err);
			return err;
		}
	}

	usb4604_switch_mode(hub, hub->mode);

	dev_info(dev, "%s: probed in %s mode\n", __func__,
			(hub->mode == USB4604_MODE_HUB) ? "hub" : "standby");

	return 0;
}

static int usb4604_i2c_probe(struct i2c_client *i2c,
			     const struct i2c_device_id *id)
{
	struct usb4604 *hub;
	int err;

	hub = devm_kzalloc(&i2c->dev, sizeof(struct usb4604), GFP_KERNEL);
	if (!hub)
		return -ENOMEM;

	i2c_set_clientdata(i2c, hub);
	hub->regmap = devm_regmap_init_i2c(i2c, &usb4604_regmap_config);
	if (IS_ERR(hub->regmap)) {
		err = PTR_ERR(hub->regmap);
		dev_err(&i2c->dev, "Failed to initialise regmap: %d\n", err);
		return err;
	}
	hub->dev = &i2c->dev;

	return usb4604_probe(hub);
}

static int usb4604_i2c_remove(struct i2c_client *i2c)
{
	struct usb4604 *hub;

	hub = i2c_get_clientdata(i2c);
	if (hub->clk)
		clk_disable_unprepare(hub->clk);

	return 0;
}

static int usb4604_platform_probe(struct platform_device *pdev)
{
	struct usb4604 *hub;

	hub = devm_kzalloc(&pdev->dev, sizeof(struct usb4604), GFP_KERNEL);
	if (!hub)
		return -ENOMEM;
	hub->dev = &pdev->dev;
	platform_set_drvdata(pdev, hub);

	return usb4604_probe(hub);
}

static int usb4604_platform_remove(struct platform_device *pdev)
{
	struct usb4604 *hub;

	hub = platform_get_drvdata(pdev);
	if (hub->clk)
		clk_disable_unprepare(hub->clk);

	return 0;
}

#ifdef CONFIG_PM_SLEEP
static int usb4604_i2c_suspend(struct device *dev)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct usb4604 *hub = i2c_get_clientdata(client);

	usb4604_switch_mode(hub, USB4604_MODE_STANDBY);

	if (hub->clk)
		clk_disable_unprepare(hub->clk);

	return 0;
}

static int usb4604_i2c_resume(struct device *dev)
{
	struct i2c_client *client = to_i2c_client(dev);
	struct usb4604 *hub = i2c_get_clientdata(client);

	if (hub->clk)
		clk_prepare_enable(hub->clk);

	usb4604_switch_mode(hub, hub->mode);

	return 0;
}
#endif

static SIMPLE_DEV_PM_OPS(usb4604_i2c_pm_ops, usb4604_i2c_suspend,
		usb4604_i2c_resume);

static const struct i2c_device_id usb4604_id[] = {
	{ USB4604_I2C_NAME, 0 },
	{ }
};
MODULE_DEVICE_TABLE(i2c, usb4604_id);

#ifdef CONFIG_OF
static const struct of_device_id usb4604_of_match[] = {
	{ .compatible = "smsc,usb4604", },
	{ .compatible = "smsc,usb4604a", },
	{},
};
MODULE_DEVICE_TABLE(of, usb4604_of_match);
#endif

static struct i2c_driver usb4604_i2c_driver = {
	.driver = {
		.name = USB4604_I2C_NAME,
		.pm = &usb4604_i2c_pm_ops,
		.of_match_table = of_match_ptr(usb4604_of_match),
	},
	.probe		= usb4604_i2c_probe,
	.remove		= usb4604_i2c_remove,
	.id_table	= usb4604_id,
};

static struct platform_driver usb4604_platform_driver = {
	.driver = {
		.name = USB4604_I2C_NAME,
		.of_match_table = of_match_ptr(usb4604_of_match),
	},
	.probe		= usb4604_platform_probe,
	.remove		= usb4604_platform_remove,
};

static int __init usb4604_init(void)
{
	int err;

	err = i2c_add_driver(&usb4604_i2c_driver);
	if (err != 0)
		pr_err("usb4604: Failed to register I2C driver: %d\n", err);

	err = platform_driver_register(&usb4604_platform_driver);
	if (err != 0)
		pr_err("usb4604: Failed to register platform driver: %d\n",
		       err);

	return 0;
}
module_init(usb4604_init);

static void __exit usb4604_exit(void)
{
	platform_driver_unregister(&usb4604_platform_driver);
	i2c_del_driver(&usb4604_i2c_driver);
}
module_exit(usb4604_exit);

MODULE_AUTHOR("Dongjin Kim <tobetter@gmail.com>");
MODULE_DESCRIPTION("USB4604 USB HUB driver");
MODULE_LICENSE("GPL");

配置

make menuconfig

 

Device Drivers  --->
	[*] USB support  --->
		<*>   EHCI HCD (USB 2.0) support
			<*>     EHCI support for Samsung S5P/EXYNOS SoC Series
		<*>   USB Mass Storage support
		<*>   USB4604 HSIC to USB20 Driver

设备树

vim arch/arm/boot/dts/exynos4412-tiny4412.dts

    usb-hub {
                    compatible = "smsc,usb4604";
                    reset-gpios = <&gpm2 4 GPIO_ACTIVE_LOW>;
                    initial-mode = <1>;
                    status = "okay";
            };
        
&exynos_usbphy {
        status = "okay";
};

&ehci {
    status = "okay";
    port@0 {
      status = "okay";
    };
    port@1 {
      status = "okay";
    };
    port@2 {
      status = "okay";
    };
};

启动

[    3.066663] dm9601 1-2.4:1.0 eth0: register 'dm9601' at usb-12580000.ehci-2.4, Davicom DM96xx USB 10/100 Ethernet, 00:00:ff:ff:00:00
[    3.173493] usb 1-2.5: new high-speed USB device number 4 using exynos-ehci
[    3.324602] usb 1-2.5: New USB device found, idVendor=0424, idProduct=2530, bcdDevice= 1.16
[    3.324696] usb 1-2.5: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[    3.324774] usb 1-2.5: Product: Bridge device

// insert U disk
[root@tiny4412 ]# [   20.623748] usb 1-2.2: new high-speed USB device number 5 using exynos-ehci
[   24.789022] usb 1-2.2: New USB device found, idVendor=0930, idProduct=6545, bcdDevice= 1.10
[   24.789244] usb 1-2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   24.789431] usb 1-2.2: Product: USB FLASH DRIVE
[   24.789576] usb 1-2.2: Manufacturer: TOSHIBA
[   24.791209] usb 1-2.2: SerialNumber: C03FD55EA867E161E00043A9
[   24.804595] usb-storage 1-2.2:1.0: USB Mass Storage device detected
[   24.817381] scsi host0: usb-storage 1-2.2:1.0
[   25.857001] scsi 0:0:0:0: Direct-Access     TOSHIBA  USB FLASH DRIVE  PMAP PQ: 0 ANSI: 6
[   25.873663] sd 0:0:0:0: [sda] 60475392 512-byte logical blocks: (31.0 GB/28.8 GiB)
[   25.874706] sd 0:0:0:0: [sda] Write Protect is off
[   25.875015] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   25.875847] random: fast init done
[   25.876123] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   27.953454]  sda: sda4
[   27.977744] sd 0:0:0:0: [sda] Attached SCSI removable disk

分析

在drivers/usb/misc/usb4604.c里面

#ifdef CONFIG_OF
static const struct of_device_id usb4604_of_match[] = {
        { .compatible = "smsc,usb4604", },
        { .compatible = "smsc,usb4604a", },
        {},
};
MODULE_DEVICE_TABLE(of, usb4604_of_match);
#endif

所以设备树里面hub相关，compatible要匹配

usb-hub {
                compatible = "smsc,usb4604";   # 
                reset-gpios = <&gpm2 4 GPIO_ACTIVE_LOW>;
                initial-mode = <1>;
                status = "okay";
        };

initial-mode = <1>;在代码里面有

enum usb4604_mode {
        USB4604_MODE_UNKNOWN,
        USB4604_MODE_HUB,          // 可知是HUB
        USB4604_MODE_STANDBY,
};

NFS启动

make menuconfig

File systems  ---> 
    [*] Network File Systems  --->
        <*>   NFS client support

配置nfs目录

sudo vim /etc/exports

/home/flinn/tiny4412-SDK/tiny4412/fs/rootfs *(rw,sync,no_root_squash)

/etc/init.d/nfs-kernel-server restart

设置启动参数

setenv ipaddr 192.168.1.123
setenv serverip 192.168.1.101

setenv bootargs noinitrd root=/dev/nfs rw nfsroot=192.168.1.101:/home/flinn/tiny4412-SDK/tiny4412/fs/rootfs ethmac=1C:6F:65:34:51:7E ip=192.168.1.123:192.168.1.101:192.168.1.1:255.255.255.0:TINY4412:eth0:off console=ttySAC0,115200 init=/linuxrc

usb start;tftp 0x40080000 uImage;tftp 0x42000000 exynos4412-tiny4412.dtb;bootm 0x40080000 - 0x42000000

以上驱动有bug ！！！

以上原理图里面没有关于i2c的接口，而驱动usb3503里面有。

会出现什么问题呢？

 

[   14.273539] Waiting up to 110 more seconds for network.
[   24.293529] Waiting up to 100 more seconds for network.

...

经常出现等2分钟还没有启动。一直没有找到原因；后面仔细分析原理图，以及代码，发现设备树也没有给定i2c的地址，那么会不会在扫描到后才能执行后面的usb4604_probe，这样的话可以解释得通；

后面试了一下，直接去掉i2c相关，改成platform_driver，完美解决问题

/*
 * Driver for SMSC USB4604 USB 2.0 hub controller driver
 *
 * Copyright (c) 2012-2013 Dongjin Kim (tobetter@gmail.com)
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 */
#include <linux/gpio.h>
#include <linux/delay.h>
#include <linux/slab.h>
#include <linux/module.h>
#include <linux/of_gpio.h>
#include <linux/platform_device.h>


#define USB4604_NAME	"usb4604"


enum usb4604_mode {
	USB4604_MODE_UNKNOWN,
	USB4604_MODE_HUB,
	USB4604_MODE_STANDBY,
};

struct usb4604_platform_data {
	enum usb4604_mode	initial_mode;
	int	gpio_reset;
};


struct usb4604 {
	enum usb4604_mode	mode;
	struct device		*dev;
	int gpio_reset;
};

static int usb4604_reset(struct usb4604 *hub, int state)
{

	if (gpio_is_valid(hub->gpio_reset))
		gpio_set_value_cansleep(hub->gpio_reset, state);
	dev_info(hub->dev, "%s\n", __func__);
	/* Wait T_HUBINIT == 1ms for hub logic to stabilize */
	usleep_range(1000, 4000);

	return 0;
}

static int usb4604_connect(struct usb4604 *hub)
{
	struct device *dev = hub->dev;
	int err;
	dev_info(hub->dev, "%s\n", __func__);
	usb4604_reset(hub, 1);
	hub->mode = USB4604_MODE_HUB;
	dev_info(dev, "switched to HUB mode\n");

	return 0;
}

static int usb4604_switch_mode(struct usb4604 *hub, enum usb4604_mode mode)
{
	struct device *dev = hub->dev;
	int err = 0;
	dev_info(hub->dev, "%s: mode:%d\n", __func__,mode);

	switch (mode) {
	case USB4604_MODE_HUB:
		/*
		 * 1. reset usb4604 first
		 * 2. switch to HUB mode
		 */
		usb4604_reset(hub, 0);
		err = usb4604_connect(hub);
		break;

	case USB4604_MODE_STANDBY:
		usb4604_reset(hub, 0);
		dev_info(dev, "switched to STANDBY mode\n");
		break;

	default:
		dev_err(dev, "unknown mode is requested\n");
		err = -EINVAL;
		break;
	}

	return err;
}

static int usb4604_probe(struct usb4604 *hub)
{
	struct device *dev = hub->dev;
	struct usb4604_platform_data *pdata = dev_get_platdata(dev);
	struct device_node *np = dev->of_node;
	int err;
	u32 mode = USB4604_MODE_HUB;

	if (pdata) {
		hub->gpio_reset	= pdata->gpio_reset;
		hub->mode = pdata->initial_mode;
	} else if (np) {
		hub->gpio_reset = of_get_named_gpio(np, "reset-gpios", 0);
		if(-EPROBE_DEFER == hub->gpio_reset)
			return -EPROBE_DEFER;
		of_property_read_u32(np, "initial-mode", &mode);
		hub->mode = mode;
	}
	
	if (gpio_is_valid(hub->gpio_reset)) {
		err = devm_gpio_request_one(dev, hub->gpio_reset,
				GPIOF_OUT_INIT_LOW, "usb4604 reset");
		if (err) {
			dev_err(dev,
				"unable to request GPIO %d as reset pin (%d)\n",
				hub->gpio_reset, err);
			return err;
		}
	}

	usb4604_switch_mode(hub, hub->mode);

	dev_info(dev, "%s: probed in %s mode\n", __func__,
			(hub->mode == USB4604_MODE_HUB) ? "hub" : "standby");

	return 0;
}

static int usb4604_platform_probe(struct platform_device *pdev)
{
	struct usb4604 *hub;

	hub = devm_kzalloc(&pdev->dev, sizeof(struct usb4604), GFP_KERNEL);
	if (!hub)
		return -ENOMEM;
	hub->dev = &pdev->dev;

	return usb4604_probe(hub);
}


#ifdef CONFIG_OF
static const struct of_device_id usb4604_of_match[] = {
	{ .compatible = "smsc,usb4604", },
	{},
};
MODULE_DEVICE_TABLE(of, usb4604_of_match);
#endif


static struct platform_driver usb4604_platform_driver = {
	.driver = {
		.name = USB4604_NAME,
		.of_match_table = of_match_ptr(usb4604_of_match),
	},
	.probe		= usb4604_platform_probe,
};

static int __init usb4604_init(void)
{
	int err;


	err = platform_driver_register(&usb4604_platform_driver);
	if (err != 0)
		pr_err("usb4604: Failed to register platform driver: %d\n",
		       err);

	return 0;
}
module_init(usb4604_init);

static void __exit usb4604_exit(void)
{
	platform_driver_unregister(&usb4604_platform_driver);

}
module_exit(usb4604_exit);

MODULE_DESCRIPTION("USB4604 USB HUB driver");
MODULE_LICENSE("GPL");

 

有崖
关注
  • 0
    点赞
  • 踩
  • 5
    收藏
    觉得还不错? 一键收藏
  • 0
    评论
专栏目录
19 开发USB光谱仪设备驱动_Tiny4412.zip
05-24
使用的光谱仪设备是USB接口的，厂家只提供了windows下的驱动和配套软件，不支持Linux使用，也没有完善的资料，现在设备想在Linux系统下使用，要支持PClinux和嵌入式Linux设备，只能自己重新开发一个驱动再编写一个配套的上位机(上位机是采用QT写的)。
linux移植网卡驱动问题(itop-4412)
ComputerInBook的专栏
07-24 1120
针对itop-4412这个板子移植网卡驱动，本来以为非常简单的，结果费了老大的劲还不能成功，经过反复厂家提供的编辑过的内核，发现内核linux-4.14.2中drivers/char/目录下有个power_ctrl.c这样一个文件，这应该是这个网卡dm9625的电源驱动代码，如果不将这个编入内核，网卡灯死活不亮，而虽然内核中有这个文件，最关键的一点，是在Makefile中即没有将它加入进去，导致代码一样，运行起来却老是失败。而在内核linux-5.6.8中，没有这个power_ctrl.c文...
itop4412 uboot-202301移植
fengconglin的博客
05-16 620
iTop4412 1G pop 精英版 u-boot-202301移植
exynos4412驱动程序教程.0
leva的博客
08-30 224
字符设备驱动 字符设备是Linux 驱动中最基本的一类设备驱动，字符设备就是一个一个字节，按照字节流进行读写操作的设备，读写数据是分先后顺序的。比如我们最常见的点灯、按键、IIC、SPI，LCD 等等都是字符设备，这些设备的驱动就叫做字符设备驱动。 在详细的学习字符设备驱动架构之前，我们先来简单的了解一下Linux 下的应用程序是如 何调用驱动程序的，Linux 应用程序对驱动程序的调用如图 在Linux 中一切皆为文件，驱动加载成功以后会在“/dev”目录下生成一个相应的文件，应 用程序通过对这个名为“
linux 内核 网卡驱动 移植,linux内核移植步骤添加dm9000网卡驱动(设备树).docx
weixin_30831529的博客
04-29 325
linux内核移植步骤添加dm9000网卡驱动(设备树).docx LINUX内核移植步骤2015年05月13日星期三上午1105往设备树中添加网卡驱动1、选平台，指定交叉编译工具链1、在MAKEFILE中指定源码顶层目录下MAKEFILEARCHSUBARCHCROSS_COMPILECONFIG_CROSS_COMPILE““改为ARCHARMCROSS_COMPILEARMLINUX2、编译...
tiny4412 windows下的DNW驱动
04-21
【标题】"tiny4412 windows下的DNW驱动"涉及到的是在Windows操作系统上为基于Samsung S5PC110（通常称为tiny4412）微处理器的开发板安装和使用DNW（Download Now）驱动的过程。DNW是三星推出的一种用于固件更新和...
tiny4412背光驱动，移植到linux-6.1
最新发布
12-22
在这个项目中，我们讨论的是将tiny4412背光驱动程序成功移植到了最新的Linux 6.1内核。 首先，我们要理解tiny4412背光驱动的原理。这种驱动通常包含初始化代码、亮度调节逻辑以及中断处理函数。在初始化阶段，驱动...
examples-tiny4412-20131010_tiny4412蜂鸣器驱动文件_
10-03
在本文中，我们将深入探讨与"examples-tiny4412-20131010_tiny4412蜂鸣器驱动文件_"相关的技术细节，这是一份针对Samsung Tiny4412微控制器的蜂鸣器驱动程序。Tiny4412是一款基于ARM Cortex-M4内核的高性能、低功耗...
tiny4412 linux3.5下按键驱动程序
12-10
tiny4412 Linux系统下的按键驱动程序 ，非常内核带的驱动，经过修改，简化、并且部分代码标准化了的。非常适合初始linux 驱动的人。本人会把 按键驱动 一步一步完善，并且分开上传，初始者可以按键顺序下载来学习。...
嵌入式开发板iTOP-4412在Ubuntu下配置WIFI方法
02-26
嵌入式开发板iTOP-4412在Ubuntu下配置WIFI方法
搭建好的itop4412驱动学习环境汇总 - 可直接下载使用
Jason_416的博客
04-27 666
linux-4.14.2内核 链接 itop4412_linux_official 说明 直接clone下仓库，查看README.md文件获取更多信息。 uboot-2017.11 链接 itop4412_uboot_official 说明 经我测试发现采用官方编译方法后的uboot无法正常采用fastboot烧写文件系统，这里推荐使用官方所给的编译完成的bin文件，目录为：g...
Linux系统移植实验---USB驱动的移植
sessos的博客
11-07 1468
实验八 USB驱动的移植 【实验目的】 USB接口是现在计算机系统中最通用的一种接口， 说明：在本系统移植课程实验中命令行提示符 “$”表示是在主机上执行，“#”表示在目标板执行 【实验环境】 • 主机：ubuntu 12.04发行版 • 目标机：FS4412平台 • 交叉编译工具：arm-none-linux-gnueabi-gcc 【实验步骤】 1. 修改设备树文件 $
⑯tiny4412 Linux驱动开发之网络子系统和USB子系统结合驱动程序
qq_23922117的博客
06-23 1248
本次比较特殊,一次介绍两个Linux子系统,主要原因是和以往的DM9000接口不同,DM9621是USB接口的.我们先来看一下tiny4412上DM9621的接口特性,如下是DM9621的电路图:如上图青靛色的部分,它是连接在外接的USB Hub上的,USB Hub的型号是USB4604,电路连接如下:从上面的电路连接结构可以看出,usb网卡连接在图中青靛色地方,还有两组是扩展USB接口,另外一组...
linux-kernel-4.4 移植 （3） 网卡移植
weixin_30555515的博客
04-25 319
开发环境：win10 64位+ VMware12 + Ubuntu14.04 32位 工具链：linaro提供的gcc-linaro-6.1.1-2016.08-x86_64_arm-linux-gnueabi 要移植的kernel版本：linux-4.4 Tiny4412开发板硬件版本为： 底板：Tiny4412SDK 1312B 核心板：Tiny4412 - 130...
HSIC Description
landishu的专栏
09-27 1148
http://cqy-chenqiyao.blog.163.com/blog/static/66857812201162810112750/ High-Speed Inter-Chip USB [HSIC]; a USB chip-to-chip interconnect. HSIC removes the analog transceivers found in normal USB.
【教程】迅为iTOP-4412精英版exynos4412开发板搭建原生Linux最小系统（四）
ZLK1214的专栏
09-03 1790
[上一篇] 配置用户账户 到目前为止，我们的最小Linux系统里面还没有任何用户账户，就连root账户也没有。 我们执行whoami命令查看当前登录的用户，提示找不到0号用户： / # whoami whoami: unknown uid 0 用ls -l命令查看文件列表时，也只能看用户和组的ID号（root用户id为0），看不到名称： / # ls -l root total 28 -rwxr-xr-x 1 0 0 170 Jan 1 00:1
tiny4412 支持网络
wit_yuan的专栏
01-23 664
1.原理图与说明 1.1 原理图 1.2 说明 tiny4412使用的网卡芯片是DM9621，是usb接口的，而且并没有直接连接到exynos4412上，中间通过一个hub芯片usb4640，然后usb4640通过HSIC接口（XhsicSTROBE0和XhsicDATA0）连接到tiny4412上。 2.软件支持 DM9621的驱动在Linux4.4.1中在driver/net/usb/dm9601.c中实现了，我们需要在内核配置中将DM9601的驱动编译进内核，linux内核支持如下: Device D
exynos4412中文手册（31章）USB2.0 Host Controller
weixin_38503722的博客
07-24 926
31.1概述 Exynos4412 SCP支持三路USB主接口，接口的关键特性如下： 遵从EHCI1.0a版本和OHCI1.0版本（两者都兼容）遵从USB2.0规格遵从USB1.0规格遵从UTMI,1.05版本，或者UTMI+3,1.0版本遵从HSIC，1.0版本支持高速（480Mbps）外设支持电源管理特性，像：    ---全部暂停/功能恢复，包括远程唤醒    ---主机
USB和Ethernet协议了解与原理图分析
Jason_416的博客
12-23 5849
前言 板载硬件支持 iTop4412 开发板SOC采用Exynos4412，是一款比较成熟，性能很强的SOC。核心板板载USB3503，引出高性能HSIC，实现2路USB HOST输出。本专题主要是在Uboot中驱动USB Device - DM9621 (Davicom DM96xx USB 10/100 Ethernet)，下面会简单介绍下硬件背景，怎么去初始化芯片。 说明 既然DM9621为...
Tiny4412 Android硬件开发指南
"Tiny4412 Android硬件开发...总而言之，《Tiny4412 Android硬件开发指南》是一份全面的参考资料，旨在帮助开发者充分利用Tiny4412开发板进行Android应用和硬件驱动的开发，通过实践掌握Android系统的硬件交互技术。

“相关推荐”对你有帮助么？

  • 非常没帮助
  • 没帮助
  • 一般
  • 有帮助
  • 非常有帮助
提交
评论
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付：10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明：

1.余额是钱包充值的虚拟货币，按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载，可以购买VIP、付费专栏及课程。

余额充值