0.96寸4引脚(IIC协议)OLED驱动程序

最新推荐文章于 2023-07-14 17:32:32 发布

qq_37405067

最新推荐文章于 2023-07-14 17:32:32 发布

阅读量5.1k

点赞数 16

分类专栏： STM32 C语言

本文链接：https://blog.csdn.net/qq_37405067/article/details/109726955

版权

STM32 同时被 2 个专栏收录

6 篇文章

订阅专栏

C语言

4 篇文章

订阅专栏

使用STM32F103xxx对0.96寸OLED进行驱动显示。

1.IIC协议代码 iic.c

#include "iic.h"
#include "delay.h"
//	 
 
//IIC端口初始化
void IIC_Init(void)
{					     
	GPIO_InitTypeDef GPIO_InitStructure;
	RCC_APB2PeriphClockCmd(	RCC_APB2Periph_GPIOB, ENABLE );	//使能GPIOB时钟
	   
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1|GPIO_Pin_10;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP ;       //推挽输出
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_Init(GPIOB, &GPIO_InitStructure);
	GPIO_SetBits(GPIOB,GPIO_Pin_1|GPIO_Pin_10); 	        //PB1,PB10输出高电平
}

//产生IIC起始信号
void IIC_Start(void)
{
	SDA_OUT();     //SDA设置输出
	IIC_SDA=1;	  	  
	IIC_SCL=1;
	delay_us(4);
 	IIC_SDA=0;//START:when CLK is high,DATA change form high to low 
	delay_us(4);
	IIC_SCL=0;//钳住IIC总线，准备发送或接收数据
}	  
//产生停止信号
void IIC_Stop(void)
{
	SDA_OUT();//SDA设置输出
	IIC_SCL=0;
	IIC_SDA=0;//STOP:when CLK is high DATA change form low to high
 	delay_us(4);
	IIC_SCL=1; 
	IIC_SDA=1;
	delay_us(4);							   	
}
//等待应答信号到来
//返回1接收应答失败，0成功
u8 IIC_Wait_Ack(void)
{
	u8 ucErrTime=0;
	SDA_IN();      //SDA设置输入
	IIC_SDA=1;delay_us(1);	   
	IIC_SCL=1;delay_us(1);	 
	while(READ_SDA)
	{
		ucErrTime++;
		if(ucErrTime>250)
		{
			IIC_Stop();
			return 1;
		}
	}
	IIC_SCL=0;  
	return 0;  
} 
//产生ACK应答
void IIC_Ack(void)
{
	IIC_SCL=0;
	SDA_OUT();
	IIC_SDA=0;
	delay_us(2);
	IIC_SCL=1;
	delay_us(2);
	IIC_SCL=0;
}
//不产生ACK应答    
void IIC_NAck(void)
{
	IIC_SCL=0;
	SDA_OUT();
	IIC_SDA=1;
	delay_us(2);
	IIC_SCL=1;
	delay_us(2);
	IIC_SCL=0;
}					 				     
//IIC发送一个字节
//返回从机有无应带
//1有应答
//0无应答			  
void IIC_Send_Byte(u8 txd)
{                        
    u8 t; 
  
    SDA_OUT(); 	    
    IIC_SCL=0;//拉低时钟开始传输数据
    for(t=0;t<8;t++)
    {              
	if((txd&0x80)>>7)
	    IIC_SDA=1;
	else
	    IIC_SDA=0;
	txd<<=1; 	  
	delay_us(2);   
	IIC_SCL=1;
	delay_us(2); 
	IIC_SCL=0;	
	delay_us(2);
    }	 
} 	
    
//读一个字节数据
u8 IIC_Read_Byte(unsigned char ack)
{
    unsigned char i,receive=0;
    SDA_IN();//SDA设置输入
    for(i=0;i<8;i++ )
    {
        IIC_SCL=0; 
        delay_us(2);
	IIC_SCL=1;
        receive<<=1;
        if(READ_SDA)receive++;   
	delay_us(1); 
    }					 
    if (!ack)
        IIC_NAck();//发送nACK
    else
        IIC_Ack(); //发送ACK   
    return receive;
}

2.IIC协议代码 iic.h

#ifndef __IIC_H
#define __IIC_H
#include "sys.h"
//	 

//IO方向设置
 
#define SDA_IN()  {GPIOB->CRL&=0XFFFFFF0F;GPIOB->CRL|=(u32)8<<4;}
#define SDA_OUT() {GPIOB->CRL&=0XFFFFFF0F;GPIOB->CRL|=(u32)3<<4;}
 
#define IIC_SCL    PBout(10) //SCL
#define IIC_SDA    PBout(1) //发送SDA	 
#define READ_SDA   PBin(1)  //输入SDA 

//IIC相关函数
void IIC_Init(void);               		 
void IIC_Start(void);				
void IIC_Stop(void);	  			
void IIC_Send_Byte(u8 txd);			
u8 IIC_Read_Byte(unsigned char ack);
u8 IIC_Wait_Ack(void); 				
void IIC_Ack(void);					
void IIC_NAck(void);				

void IIC_Write_One_Byte(u8 daddr,u8 addr,u8 data);
u8 IIC_Read_One_Byte(u8 daddr,u8 addr);	  
#endif

在设置IO口方向中，是直接设置的寄存器CRL或CRH。CRL和CRH是设置IO口输出/输入模式的，CRL设置0-7号GPIO，CRH设置8-15号GPIO，并且每四位设置一个GPIO，按照高低位对应。我设置的SDA数据引脚为PB1，即要设置CRL[4:7]，通过GPIOB->CRL&=0XFFFFFF0F;对CRL[4:7]清0，再由GPIOB->CRL|=(u32)8<<4;装载新的数据。由于要设置CRL[4:7]，所要32位的数据左移4位。在任意一个GPIO中，数据1000为输入，0011为输出。

3.OLED显示 display.c

#include"display.h"
#include"point.h"
#include"sys.h"
#include"delay.h"
#include"iic.h"
#include "time.h"

extern const u8 ASCII_8_16[][16];

extern const u8 ChineseFont_16_16[][32];

/*
函数功能：向OLED写入一个字节
参数：
dat:写入的数据/命令
cmd:1为写数据 0为写命令
*/
void OLED_WR_Byte(u8 dat,u8 cmd)
{
	IIC_Start();	         //IIC开始信号
	IIC_Send_Byte(0x78);     //传输地址
	IIC_Wait_Ack();		 //接收ACK
	if(cmd) IIC_Send_Byte(0x40);	 //写数据
	else IIC_Send_Byte(0x00);	 //写命令
	IIC_Wait_Ack();		 //接收ACK
	IIC_Send_Byte(dat);	 //发送数据/命令
	IIC_Wait_Ack();		 //接收ACK
	IIC_Stop();		 //IIC停止
}

/*
函数功能：清屏
*/
void OLED_Clear(void)  
{  
	u8 i,n;  
	for(i=0;i<8;i++)
	{
		OLED_WR_Byte(0xB0+i,OLED_CMD);  //行地址（0-7）
		OLED_WR_Byte(0x00,OLED_CMD);    //从（0，0）开始
		OLED_WR_Byte(0x10,OLED_CMD);    
		for(n=0;n<128;n++)
		{
			OLED_WR_Byte(0x00,OLED_DATA);
		}
	}
}

/*
函数功能：设置显示起始位置
参数: x=0~127   列
	  y=0~7 行
*/
void OLED_SetCursorAddrese(u8 x,u8 y)
{
		OLED_WR_Byte(0xB0+y,OLED_CMD); 	
		OLED_WR_Byte((x&0xF0)>>4|0x10,OLED_CMD);
		OLED_WR_Byte((x&0x0F)|0x00,OLED_CMD);  		
}

/*
函数功能：OLED初始化
*/
void OLED_Init(void)
{
	delay_ms(500);							
	OLED_WR_Byte(0xAE,OLED_CMD);
	OLED_WR_Byte(0x00,OLED_CMD);
	OLED_WR_Byte(0x10,OLED_CMD);
	OLED_WR_Byte(0x40,OLED_CMD);
	OLED_WR_Byte(0x81,OLED_CMD);
	OLED_WR_Byte(0xCF,OLED_CMD);
	OLED_WR_Byte(0xA1,OLED_CMD);
	OLED_WR_Byte(0xC8,OLED_CMD);
	OLED_WR_Byte(0xA6,OLED_CMD);
	OLED_WR_Byte(0xA8,OLED_CMD);
	OLED_WR_Byte(0x3F,OLED_CMD);
	OLED_WR_Byte(0xD3,OLED_CMD);
	OLED_WR_Byte(0x00,OLED_CMD);
	OLED_WR_Byte(0xD5,OLED_CMD);
	OLED_WR_Byte(0x80,OLED_CMD);
	OLED_WR_Byte(0xD9,OLED_CMD);
	OLED_WR_Byte(0xF1,OLED_CMD);
	OLED_WR_Byte(0xDA,OLED_CMD);
	OLED_WR_Byte(0x12,OLED_CMD);
	OLED_WR_Byte(0xDB,OLED_CMD);
	OLED_WR_Byte(0x40,OLED_CMD);
	OLED_WR_Byte(0x20,OLED_CMD);
	OLED_WR_Byte(0x02,OLED_CMD);
	OLED_WR_Byte(0x8D,OLED_CMD);
	OLED_WR_Byte(0x14,OLED_CMD);
	OLED_WR_Byte(0xA4,OLED_CMD);
	OLED_WR_Byte(0xA6,OLED_CMD);
	OLED_WR_Byte(0xAF,OLED_CMD);
	OLED_Clear();
	OLED_SetCursorAddrese(0,0); 
}

/*
函数功能：显示8*16字符串
参数：x=0-127 y=0-7
      height：高度
      str：字符串首地址
*/
void OLED_DisplayString(u8 x,u8 y,u8 height,u8 *str)
{
    u8 addr=0,i;
	
    while(*str!='\0') 
    {
	if(*str >= ' '&& *str <= '~')             
        {
	    addr=*str-' ';                          //取出相对地址
	    OLED_SetCursorAddrese(x,y);             //显示地址
	    for(i=0;i<height/2;i++)      
	    {
		OLED_WR_Byte(ASCII_8_16[addr][i],OLED_DATA); 
	    }
	    OLED_SetCursorAddrese(x,y+1); 
	    for(i=0;i<height/2;i++)        
	    {
		OLED_WR_Byte(ASCII_8_16[addr][i+height/2],OLED_DATA); 
	    }
	    str++;
	    x+=height/2; 		   
        }
    }
}

/*
函数功能：显示16*16的中文
参数：x=0-127 y=0-7
add: 二维数组的行地址
font_long：显示的中文字数
*/
void OLED_DisplayChinese(u8 x,u8 y,u8 add,u8 font_long)
{
	u8 i;
	 
	while(font_long--)
	{
		OLED_SetCursorAddrese(x,y);           //显示地址
		for(i=0;i<16;i++)      
		{
			OLED_WR_Byte(ChineseFont_16_16[add][i],OLED_DATA); 
		}
		OLED_SetCursorAddrese(x,y+1); 
		for(i=0;i<16;i++)        
		{
			OLED_WR_Byte(ChineseFont_16_16[add][i+16],OLED_DATA); 
		}
		x+=16; 		
		add++;
	}
}

4.OLED显示 display.h

#ifndef __DISPLAY_H
#define __DISPLAY_H
#include "stm32f10x.h"
 

#define OLED_CMD 				0		//命令
#define OLED_DATA 				1		//数据

//相关函数
void OLED_Init(void);
void OLED_DisplayString(u8 x,u8 y,u8 height,u8 *str);
void OLED_DisplayChinese(u8 x,u8 y,u8 add,u8 font_long);
	
#endif

5.字库 word.c

word.c中的字符数据是由PCtoLCD2002取字模软件生成的，在取字模时要设置软件，设置点阵格式为阴码，取模走向为逆向，取模方式为列行式。

#include "word.h"
#include "sys.h"

// ASCII字符集 大小8*16
const u8 ASCII_8_16[][16]=
{
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x10,0x0C,0x02,0x10,0x0C,0x02,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*""",2*/
{0x00,0x40,0xC0,0x78,0x40,0xC0,0x78,0x00,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x00},/*"#",3*/
{0x00,0x70,0x88,0x88,0xFC,0x08,0x30,0x00,0x00,0x18,0x20,0x20,0xFF,0x21,0x1E,0x00},/*"$",4*/
{0xF0,0x08,0xF0,0x80,0x60,0x18,0x00,0x00,0x00,0x31,0x0C,0x03,0x1E,0x21,0x1E,0x00},/*"%",5*/
{0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x2C,0x19,0x27,0x21,0x10},/*"&",6*/
{0x00,0x12,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00},/*"(",8*/
{0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00},/*")",9*/
{0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00},/*"*",10*/
{0x00,0x00,0x00,0x00,0xE0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x0F,0x01,0x01,0x01},/*"+",11*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x90,0x70,0x00,0x00,0x00,0x00,0x00},/*",",12*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x00},/*"-",13*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x00,0x00,0x00,0xC0,0x38,0x04,0x00,0x00,0x60,0x18,0x07,0x00,0x00,0x00,0x00},/*"/",15*/
{0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00},/*"0",16*/
{0x00,0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00},/*"1",17*/
{0x00,0x70,0x08,0x08,0x08,0x08,0xF0,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00},/*"2",18*/
{0x00,0x30,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x18,0x20,0x21,0x21,0x22,0x1C,0x00},/*"3",19*/
{0x00,0x00,0x80,0x40,0x30,0xF8,0x00,0x00,0x00,0x06,0x05,0x24,0x24,0x3F,0x24,0x24},/*"4",20*/
{0x00,0xF8,0x88,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x20,0x20,0x20,0x11,0x0E,0x00},/*"5",21*/
{0x00,0xE0,0x10,0x88,0x88,0x90,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x20,0x1F,0x00},/*"6",22*/
{0x00,0x18,0x08,0x08,0x88,0x68,0x18,0x00,0x00,0x00,0x00,0x3E,0x01,0x00,0x00,0x00},/*"7",23*/
{0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00},/*"8",24*/
{0x00,0xF0,0x08,0x08,0x08,0x10,0xE0,0x00,0x00,0x01,0x12,0x22,0x22,0x11,0x0F,0x00},/*"9",25*/
{0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0x00,0x00,0x00,0x00},/*";",27*/
{0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00},/*"<",28*/
{0x00,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x00,0x02,0x02,0x02,0x02,0x02,0x02,0x00},/*"=",29*/
{0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00},/*">",30*/
{0x00,0x70,0x48,0x08,0x08,0x88,0x70,0x00,0x00,0x00,0x00,0x30,0x37,0x00,0x00,0x00},/*"?",31*/
{0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x28,0x2F,0x28,0x17,0x00},/*"@",32*/
{0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20},/*"A",33*/
{0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00},/*"B",34*/
{0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00},/*"C",35*/
{0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00},/*"D",36*/
{0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00},/*"E",37*/
{0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00},/*"F",38*/
{0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00},/*"G",39*/
{0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20},/*"H",40*/
{0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"I",41*/
{0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00},/*"J",42*/
{0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00},/*"K",43*/
{0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00},/*"L",44*/
{0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x01,0x3E,0x01,0x3F,0x20,0x00},/*"M",45*/
{0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00},/*"N",46*/
{0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00},/*"O",47*/
{0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00},/*"P",48*/
{0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x28,0x28,0x30,0x50,0x4F,0x00},/*"Q",49*/
{0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20},/*"R",50*/
{0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00},/*"S",51*/
{0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00},/*"T",52*/
{0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00},/*"U",53*/
{0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00},/*"V",54*/
{0x08,0xF8,0x00,0xF8,0x00,0xF8,0x08,0x00,0x00,0x03,0x3E,0x01,0x3E,0x03,0x00,0x00},/*"W",55*/
{0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20},/*"X",56*/
{0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00},/*"Y",57*/
{0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00},/*"Z",58*/
{0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00},/*"[",59*/
{0x00,0x04,0x38,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00},/*"\",60*/
{0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x04,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80},/*"_",63*/
{0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x19,0x24,0x24,0x12,0x3F,0x20,0x00},/*"a",65*/
{0x10,0xF0,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00},/*"b",66*/
{0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00},/*"c",67*/
{0x00,0x00,0x80,0x80,0x80,0x90,0xF0,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20},/*"d",68*/
{0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x24,0x24,0x24,0x24,0x17,0x00},/*"e",69*/
{0x00,0x80,0x80,0xE0,0x90,0x90,0x20,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"f",70*/
{0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00},/*"g",71*/
{0x10,0xF0,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20},/*"h",72*/
{0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00},/*"j",74*/
{0x10,0xF0,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x06,0x29,0x30,0x20,0x00},/*"k",75*/
{0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00},/*"l",76*/
{0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F},/*"m",77*/
{0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20},/*"n",78*/
{0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00},/*"o",79*/
{0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0x91,0x20,0x20,0x11,0x0E,0x00},/*"p",80*/
{0x00,0x00,0x00,0x80,0x80,0x00,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0x91,0xFF,0x80},/*"q",81*/
{0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00},/*"r",82*/
{0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00},/*"s",83*/
{0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x10,0x00},/*"t",84*/
{0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20},/*"u",85*/
{0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x03,0x0C,0x30,0x0C,0x03,0x00,0x00},/*"v",86*/
{0x80,0x80,0x00,0x80,0x80,0x00,0x80,0x80,0x01,0x0E,0x30,0x0C,0x07,0x38,0x06,0x01},/*"w",87*/
{0x00,0x80,0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x20,0x31,0x0E,0x2E,0x31,0x20,0x00},/*"x",88*/
{0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x81,0x86,0x78,0x18,0x06,0x01,0x00},/*"y",89*/
{0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x00,0xFC,0x02,0x02,0x00,0x00,0x00,0x00,0x01,0x3E,0x40,0x40},/*"{",91*/
{0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00},/*"|",92*/
{0x02,0x02,0xFC,0x00,0x00,0x00,0x00,0x00,0x40,0x40,0x3E,0x01,0x00,0x00,0x00,0x00},/*"}",93*/
{0x00,0x80,0x40,0x80,0x80,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x00},/*"~",94*/
};

//中文字库 大小16*16
const u8 ChineseFont_16_16[][32] = {
{0x10,0x10,0x10,0xFF,0x10,0x10,0xF0,0x00,0x00,0xF8,0x08,0x08,0x08,0xF8,0x00,0x00,
0x80,0x40,0x30,0x0F,0x40,0x80,0x7F,0x00,0x00,0x7F,0x20,0x20,0x20,0x7F,0x00,0x00},//加

{0x90,0x94,0x94,0xF4,0x9F,0x94,0x94,0x94,0x10,0x10,0xFF,0x10,0x12,0xD4,0x10,0x00,
0x20,0x26,0x25,0x24,0xFE,0x14,0x14,0x14,0x80,0x40,0x27,0x18,0x26,0x41,0xF0,0x00},//载

{0x08,0x08,0x08,0x08,0x08,0xF8,0x89,0x8E,0x88,0x88,0x88,0x88,0x08,0x08,0x08,0x00,
0x00,0x80,0x40,0x20,0x18,0x07,0x00,0x00,0x40,0x80,0x40,0x3F,0x00,0x00,0x00,0x00},//方

{0x00,0xF8,0x08,0x08,0x0C,0xCA,0x49,0x48,0x48,0xC8,0x08,0x08,0x08,0xF8,0x00,0x00,
0x00,0xFF,0x00,0x00,0x00,0x1F,0x08,0x08,0x08,0x1F,0x00,0x40,0x80,0x7F,0x00,0x00},//向

{0x00,0x00,0xF8,0x88,0x88,0x88,0x88,0xFF,0x88,0x88,0x88,0x88,0xF8,0x00,0x00,0x00,
0x00,0x00,0x1F,0x08,0x08,0x08,0x08,0x7F,0x88,0x88,0x88,0x88,0x9F,0x80,0xF0,0x00},//电

{0x10,0x60,0x02,0x8C,0x00,0x44,0x64,0x54,0x4D,0x46,0x44,0x54,0x64,0xC4,0x04,0x00,
0x04,0x04,0x7E,0x01,0x80,0x40,0x3E,0x00,0x00,0xFE,0x00,0x00,0x7E,0x80,0xE0,0x00},//流
};

6.字库 word.c

#ifndef WORD_H
#define WORD_H
#include "sys.h"

extern const u8 ASCII_8_16[][16];

extern const u8 ChineseFont_16_16[][32];

#endif

7.主函数 main.c

#include "stm32f10x.h"
#include "usart.h"
#include "delay.h"
#include "usart.h"
#include "display.h"
#include "iic.h"

int main( void )
{	
	NVIC_PriorityGroupConfig( NVIC_PriorityGroup_2 );
	uart_init(115200);
	delay_init();
	
        IIC_Init();
	
	OLED_Init();     //OLED初始化
	delay_ms(100);  
	OLED_DisplayChinese(24,0,0,4);   //加载方向
	OLED_DisplayString(88,0,16,":");
	OLED_DisplayChinese(24,3,4,2);   //电流
	OLED_DisplayString(56,3,16,":");
	OLED_DisplayString(88,3,16,"mA");
	
	while(1）;
}

8.效果图