电赛 电容触摸串口屏

   九层妖塔 起于垒土

---

---

一、分类：电阻屏 or 电容屏

触摸屏基本原理介绍
触摸屏工作原理解析
STM32CubeMX系列|触摸屏

二、淘晶驰电容触摸串口屏

USART HMI 资料中心

三、上位机

四、MCU

main.c

#include <STC15.H>
#include <intrins.h>
#include <UART.H>

#define uchar unsigned char
#define uint unsigned int
	


uchar Receive;
uchar S1_num;
uchar S4_num;
void GPIO(void);      //IO口初始化函数

void Delay10ms();		//@11.0592MHz

void main(void)
{

	
	GPIO();
	UartInit();       //串行口1初始化函数
 	ES=1;
	EA=1;
  S1 = 1 ; S2 = 1; S3 = 0; S4 = 0; S5 = 0;
	
	while(1)
	{

//				 UART_Send_start();//为确保串口HMI正常通信  
//	       UART_Send_Str("page0.t0.txt=\"灯1亮\"");
//         UART_Send_END(); 
//	       Delay10ms();
//		
//				  UART_Send_start();//为确保串口HMI正常通信  
//	        UART_Send_Str("page0.t0.txt=\"灯1灭\"");
//          UART_Send_END(); 


	}

}


//-----------------------------------IO口初始化函数-----------------------------//
void GPIO(void)
{
	P0M1=0;
	P0M0=0;
	P1M1=0;
	P1M0=0;
	P2M1=0;
	P2M0=0;
	P3M1=0;
	P3M0=0;
	P4M1=0;
	P4M0=0;
	P5M1=0;
	P5M0=0;
}

UART.H

#ifndef _UART_H_
#define _UART_H_

#include <STC15.H>
  
#define uchar unsigned char
#define uint unsigned int
	

sbit S1 = P0^0;
sbit S2 = P0^1;
sbit S3 = P0^2;
sbit S4 = P0^3;
sbit S5 = P0^4;

extern uchar Receive;

void UartInit(void);	//9600bps@11.0592MHz 串行口1初始化函数
void UART_Send_Byte(unsigned char dat);	//发送一个字节 串行发送采用查询方式
void UART_Send_Str(char *s);
void UART_Send_END(void);
void UART_Send_start(void);
void Delay10ms();		//@11.0592MHz

#endif

UART.c

#include <UART.H>
#include <intrins.h>



//-------------------------------------串行口1初始化函数-----------------------------//
void UartInit(void)		//9600bps@11.0592MHz
{
	SCON = 0x50;		 //8位数据,可变波特率
	AUXR |= 0x40;		 //定时器1时钟为Fosc,即1T
	AUXR &= 0xFE;		 //串口1选择定时器1为波特率发生器
	TMOD &= 0x0F;		 //设定定时器1为16位自动重装方式
	TL1 = 0xE0;		   //设定定时初值
	TH1 = 0xFE;		   //设定定时初值
	ET1 = 0;		     //禁止定时器1中断
	TR1 = 1;		     //启动定时器1
}

void UART_Send_Byte(unsigned char dat)	//发送一个字节 串行发送采用查询方式
{
 	//ES=0;      //关串行口1中断
  TI=0;      //清除发送中断标志位
  SBUF=dat;  //将数据写入缓冲区
  while(!TI);//等待发送结束
  TI=0;
}


void UART_Send_Str(char *s)   //发送一个字符串
{
 int i=0;
 while(s[i]!=0)
 {
 	UART_Send_Byte(s[i]);
 	i++;
 }
 
}
void UART_Send_END(void)  //发送结束信号
{
	 UART_Send_Byte(0xFF);
	 UART_Send_Byte(0xFF);
	 UART_Send_Byte(0xFF);
}


void UART_Send_start(void)
{
	 Delay10ms();	
	 UART_Send_END();
	 Delay10ms();	
}


void Delay10ms()		//@11.0592MHz
{
	unsigned char i, j;

	i = 108;
	j = 145;
	do
	{
		while (--j);
	} while (--i);
}




void uart_isr() interrupt 4
{
  if(RI==1)
   {
	  RI=0;       //清除RI位
    Receive=SBUF;
  	switch(Receive)
		{
			case 0X01: {S1 = 0 ; S2 = 1; S3 = 0; S4 = 0; S5 = 1;} break;   //交越
			case 0X02: {S1 = 1 ; S2 = 1; S3 = 0; S4 = 0; S5 = 0;} break;   //标准
			case 0X03: {S1 = 1 ; S2 = 0; S3 = 0; S4 = 0; S5 = 0;} break;   //顶部
			case 0X04: {S1 = 1 ; S2 = 1; S3 = 1; S4 = 0; S5 = 0;} break;   //底部
			case 0X05: {S1 = 1 ; S2 = 1; S3 = 0; S4 = 1; S5 = 0;} break;   //双向
		}
	 }
}