2 IS-IS基础实验

2.1 IS-IS配置

2.1.1 拓扑

2.1.2 配置步骤

以太网接口上成功建立邻居必须满足接口所属的路由器等级、接口等级、设备的区域ID相同，并且接口的地址处于同一网段。
①接口地址配置

R1：
#
interface GigabitEthernet0/0/0
 ip address 10.2.0.1 255.255.255.0 
#
interface LoopBack0
 ip address 10.1.1.1 255.255.255.255 
#
R2：
#
interface GigabitEthernet0/0/0
 ip address 10.2.0.2 255.255.255.0 
#
interface GigabitEthernet0/0/1
 ip address 20.2.0.1 255.255.255.0 
#
interface LoopBack0
 ip address 10.1.2.2 255.255.255.255 
#
R3：
#
interface GigabitEthernet0/0/0
 ip address 10.2.0.3 255.255.255.0 
#
interface GigabitEthernet0/0/1
 ip address 30.2.0.1 255.255.255.0 
#
interface LoopBack0
 ip address 10.1.3.3 255.255.255.255 
#
R4：
#
interface GigabitEthernet0/0/0
 ip address 20.2.0.2 255.255.255.0 
#
interface GigabitEthernet0/0/1
 ip address 30.2.0.2 255.255.255.0 
#
interface GigabitEthernet0/0/2
 ip address 40.2.0.1 255.255.255.0 
#
interface LoopBack0
 ip address 10.1.4.4 255.255.255.255 
#
R5：
#
interface GigabitEthernet0/0/0
 ip address 40.2.0.2 255.255.255.0 
#
interface LoopBack0
 ip address 10.1.5.5 255.255.255.255 
#

②配置IS-IS协议

R1:
#
isis 1
 is-level level-1
 network-entity 49.0001.0000.0000.0001.00
#
interface GigabitEthernet0/0/0
 isis enable 1
 isis authentication-mode simple cipher test
#
interface LoopBack0
 isis enable 1
#
R2:
#
isis 1
 network-entity 49.0001.0000.0000.0002.00
#
interface GigabitEthernet0/0/0
 isis enable 1
 isis authentication-mode simple test
#
interface GigabitEthernet0/0/1
 isis enable 1
 isis authentication-mode simple test
#
interface LoopBack0
 isis enable 1
#
R3:
#
isis 1
 network-entity 49.0001.0000.0000.0003.00
#
interface GigabitEthernet0/0/0
 isis enable 1
 isis authentication-mode simple test
#
interface GigabitEthernet0/0/1
 isis enable 1
 isis authentication-mode simple test
#
interface LoopBack0
 isis enable 1
#
R4:
#
isis 1
 is-level level-2
 network-entity 49.0002.0000.0000.0004.00
#
interface GigabitEthernet0/0/0
 isis enable 1
 isis authentication-mode simple test
#
interface GigabitEthernet0/0/1
 isis enable 1
 isis authentication-mode simple test
#
interface GigabitEthernet0/0/2
 isis enable 1
 isis authentication-mode simple test
#
interface LoopBack0
 isis enable 1
#
R5：
#
isis 1
 is-level level-2
 network-entity 49.0002.0000.0000.0005.00
#
interface GigabitEthernet0/0/0
 isis enable 1
 isis authentication-mode simple test
#
interface LoopBack0
 isis enable 1
#

③检查配置结果
查看IS-IS邻居、路由表

dis isis peer
dis isis route

④修改接口的DIS优先级
R1、R2、R3在同一广播域，需选举出DIS接口，修改DIS优先级手动指定R1的g0/0/0为DIS

修改R1的g0/0/0的DIS优先级

#
interface GigabitEthernet0/0/0
 isis dis-priority 127
#

⑤配置IS-IS路由渗透
查看R1去往10.1.5.5的路由，此时为R2、R3的负载均衡

在R3上配置isis路由渗透，将R1发往R5的流量引导至R3

R3：
#
isis 1
 import-route isis level-2 into level-1
#